Dyson DC25 All Floors Bagless Upright Vacuum\015 Suction hose came loose from plastic clip at the extention wand.\015

How to Identify and Fix Common Vacuum Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :

All accessories on the V7, V8, V10, and V11 are interchangeable and will work on any of the aforementioned models. All of these vacuums use Dyson`s red button clickable accessory system.
To add any Dyson attachment to your hose, simply slide the opening over the end of the wand. Rotate the attachment as needed to adhere it to the end of the wand. You will not hear a click or anything since the attachment relies on the tension between the 2 openings to stay in place.
Unplug the vacuum and use the Dyson Ball Animal Hose Replacement Guide to remove the vacuum`s hose and check for clogs at the base of the hose. Next, check the hose itself. Feel along-side the hose to check for a blockage. If a blockage is present, use a tool to pull out the blockage.
Adds up to 24in of flexible reach to any tool attachment, to clean up high or down low in your home or car. Engineered to fit Dyson Gen5detect™, Gen5outsize™, V15™, V12™, V11™, V10™, V8™, and V7™ vacuums​.
Taking Care Of Your Vacuum Cleaner

The only time a hose needs to be replaced is when there`s a puncture in it that prevents proper suction. If you change the tube and it still doesn`t run correctly, then there`s another issue which might indicate the need for a new vacuum cleaner.

Over time, a vacuum`s hoses can start to crack and peel, and even if there are no obvious splits, there may be microcracks causing a loss of suction. Purchase a replacement hose and use the Dyson Ball Animal Hose Replacement Guide to replace the vacuum`s hose.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

My bissell proheat upright steam cleaner is spraying out through the attachments just fine, but will not spray to the floor when using upright. we’ve taken it apart to find that there is no water at all going through one of the hoses, but it appears the hose is connected behind the on/off and heat switches, we can’t seem to figure out how to get in there to replace that hose….any suggestions on how to access this?? just curious how you would get in to replace the hose, we know it is the hose..
ANSWER : Hi,

Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.

Bissell Proheat Upright Wet/Dry Vacuum Problems

heatman101 .
.xbnxb

Torn Hose The hose on my Dyson is torn right at the top where the the accessories connect. I was able to take the connection apart and shorten the hose, but I don’t know what to use to reattach the hose to the black fitting. It looks like it was glued…not sure what kind. Any ideas?
ANSWER : Duct tape

Hose Problem The hose broke just above the cuff on the inlet end of the hose.  I found that the hose doesn’t thread into this cuff but appears to be heat bonded in some way. Can I get a replacement cuff or do I have to replace the hose?
ANSWER : Looks like you can just get the hose, part #38479-4, It should just screw into the adapter or it may be glued in.

Wand won’t go into the flexible hose
ANSWER : Try some fine sandpaper or one could heat up
the wand or hose with a heatgun or torch
to flex it and then try plugging it in.

I have an electrolux central vacuum in my house. My central vac hose has something stuck in it, I think, maybe a sock. I tried to put a long dryer wand down it but the hose is just too long. Does this need a repair man or new hose?? Any idea of a way to blow it out? Thanks.
ANSWER : The best way to clear an obstruction is to blow it out by attaching the wall end to the exhaust of a shop vacuum, or using an air compressor.
.You can try holding the wand end of the hose directly to the CV in port and turning the machine on. This provides essentially the same action as the previous method.
.If neither of these work, try a combination of the two. Or using a shop vac, hold the wall end to the exhaust of the vacuum and the wand end to the in port of the shop vac. Turn shop vac on and the obstruction should come out.
.Borrow a good strong shop vacuum if you need to.
.If these methods fail, take it to an authorized Aerus Electrolux store and have the service tech try to clear it. Care must always be taken when trying to clear an obstuction with a long object, especially if it’s pointed. I’ve seen many hoses that have shorted out and even caught fire due to the wiring accidentally being “nicked”.

No suction Hello – any help with this would be much appreciated!

I just changed the bag and filters. The machine runs, seems normal, but there is no suction. There is no blockage of the hose, as indicated by the fact that that little viewer window above where the hose connects to the unit is not showing the red portion that it shows when there is something blocking the hose (god, this is hard to describe!).

If I disconnect the hose and put my hand over the hole, I feel some suction. But

ANSWER : Well, it actually sounds like there is a blockage. Try removing your hose and dropping something through it, like a quqrter. If it comes through, no clog. If it is clogged, I believe that machine has a blower on the upper part of the cleaner (maybe in the bag compartment towards the top. You can take out the filter holder and plug the hose in there and run the unit . Does the blockage come out? If not, Try shaking the hose, or you can put a stiff wire in it to try to free it. Do not run water through it. If there is no blockage at all, then you will probably need to take it to a service center. But I am pretty confident that we are looking at a clog situation. Let me know if this fixesya! Thanks, Rene (vacuum Doctor)

I HAVE A BISSELL PROHEAT CARPET CLEANER 7920 I DISSEMBLY IT TO CLEAN IT. I DON’T KNOW IF I PUT THE HOSES BACK IN THE RIGHT LOCATION BECAUSE AFTER I PUT IT BACK TOGETHER IT’S LEAKING WATER ALL OVER THE FLOOR BUT IT WILL RECOVER THE WATER FROM THE FLOOR AND THE SOLUTION WON’T SPARY OUT I THINK THE HOSES ARE NOT IN THEIR RIGHT LOCATION TO STOP THE FLOW WHEN IT’S NOT SUPPOSE TO BE COMING OUT CONSTANTLY HELP PLEASE IS THEIR A HOSE DIAGRAM FOR THE HOSES INSIDE THE CARPET CLEANER
ANSWER : Hi,

Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.

Bissell Proheat Upright Wet/Dry Vacuum Problems

heatman101 .
.dfjddj

Hi I am wondering if someone could send me some (Schematics for a Bissell 9300-1) I took it all apart to clean out all the ( Hard watter out of the hoses) and now I cant remember where all the hoses go,I need to see where all the hoses go so I can hook up if someone could help me out! Thanks!!
ANSWER : Hi, you should be able to download the manual/manuals you need on the following web page. Just paste the following onto your search bar. I’ve used this site to find manuals before, it can be trusted. Good luck!.
http://www.manualsonline.com/ex/thread/view/idThread/656302