to keep track of or does the belt replacement depend on the type of carpet I’m cleaning? Thanks, Jim
Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
Many of these belts look very similar, but there are differences, and if you try to pick the correct belt just by how it looks, you could very easily end up with an incompatible Bissell vacuum belt for your model. Along with this, some vacuums use multiple internal belts for different functions of the vacuums.
Plug the PowerSteamer into a proper outlet and turn ON the Power switch. While pressing the trigger, slowly make several passes over the area to be cleaned. Caution: Do not overwet. Turn the machine Power switch OFF and let BISSELL Advanced Deep Cleaning Formula dissolve the tough soil for 1-2 minutes.
Common Signs of Drive Belt Replacement
- Strange Noises. One of the biggest signs that you probably need to take your vehicle to the dealership for a check is when you start hearing strange noises coming from your engine. …
- Visual Signs of Wear. …
- Mileage Indicators. …
- Breakage is Bad.
9 mars 2017
Includes one Pump Belt, COG Pump Belt, and the Brush Belt.
If too much hair, string, or lint is caught in the brushroll, the brushroll can get stuck. If the brushroll is stuck, it will put too much strain on the belt and may cause the belt to break. Remove the brushroll and clean out any debris from the bearings. After replacing the brushroll, make sure that it turns freely.
Plug the PowerSteamer into a proper outlet and turn ON the Power switch. While pressing the trigger, slowly make several passes over the area to be cleaned. Caution: Do not overwet. Turn the machine Power switch OFF and let BISSELL Advanced Deep Cleaning Formula dissolve the tough soil for 1-2 minutes.
Some manufacturers like GM or Mazda do not recommend giving a second chance to the belt once it has been taken off. On the other hand, Chrysler and Ford say the belt can be reused if there are no problems found with the belt.
Serpentine belt replacement is easy because today`s automatic drive belt tensioners eliminate the need to loosen bolts or pry components into position for retensioning. Just rotate the tensioner, remove the old belt and install a new one.
Hold the belt between finger and thumb at this point and move it from side to side. See how much it deflects at the centre of the run. If it moves more than 1/2 in. (13 mm) it is too slack – any less movement and it is too tight.
For most vehicles, the belt should not be able to be pressed down more than ½ inch. If it can be pressed lower, then the belt is too loose. Note: Manufacturers have their own specifications for how much deflection can be found in the belt. Make sure to check the owner`s manual for your specific vehicle.
Leather belts are made to be adjustable, but this only works within the size range of the belt`s length and buckle holes. Luckily, if you`ve purchased a belt with a style that you love but a size that`s rather on the large end, trimming down the length and making new buckle holes is a relatively simple matter.
Belts should never be stored above 115°F. Belts will begin to degrade after 7 years even when stored properly. Beyond seven years, assuming normal storage, a decrease in service life of approximately 10% per year can be expected.
A serpentine drive belt can make all kinds of odd noises. It can squeak, squeal, chirp and clunk, imitating a bad engine-driven accessory or engine bearing. These noises can fool even the most experienced mechanic and lead to an expensive misdiagnosis.
The serpentine belt is a single, continuous belt that drives multiple devices in your engine, such as the alternator, power steering pump, water pump, and air conditioning compressor. If your serpentine belt breaks, all of these systems will shut down and your vehicle will overheat.
Look for cracks, fraying, or splits on the top cover. Look for signs of glazing on the belt`s sides. Glazed or slick belts can slip, overheat, or crack. Twist a serpentine belt to look for separating layers, cracks, or missing chunks of the grooves on the underside.
Plug the PowerSteamer into a proper outlet and turn ON the Power switch. While pressing the trigger, slowly make several passes over the area to be cleaned. Caution: Do not overwet. Turn the machine Power switch OFF and let BISSELL Advanced Deep Cleaning Formula dissolve the tough soil for 1-2 minutes.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
How can determine when it’s time to replace the drive belt on my Bissel Power Steamer? Is there a certain number of hours of usage that I need to keep track of or does the belt replacement depend on the type of carpet I’m cleaning? Thanks, Jim
ANSWER : Usually, replacement is needed when the brush no longer runs or is intermittent. Check the brush bearings and for debris build-up whenever the belt is changed. Good luck!
Read Full Q/A … : Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum
Windtunnel belt I have a new Hoover Windtunnel canister. The belt keeps coming off. It happened a couple weeks ago (several times after putting the belt back on) so I assumed I might need a new belt as it might have dried out at the store. I ordered new belts and today I used it for about an hour and the belt came off again, twice. There doesn’t seem to be anything to hold the belt on the stem as it seems to slip off. I have tried it centered, to the left and to the right….can you help. I am v
ANSWER : I’ve successfully used a compatible belt – Royal 104425001 .It’s still new, but for the time being at least – it works.
Read Full Q/A … : Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum
We have a Bissell Proheat Cleanshot 2X Model 9500 Steam carpet cleaner. The first time we used it things were great. The second time we used it it left tracks in the carpet. We have no idea what caused this. We tried using the machine on an entirely different carpet and it did the same thing. After vacuuming the carpet about 10 or 12 times, the tracks are still embedded in the carpet – HELP!!!! We’re read and reread the manual and contacted customer service and received no help.
ANSWER : First things first. It’s only the second time you have used the machine, so it must be fairly new. If you have a receipt and the unit is less than a year old you should take it to an authorized Bissell repair center and have the machine inspected under warranty.
.
.Otherwise, The jets on this unit clog easily, there are two of them and you can locate them under the recovery tank towards the front of the machine, and blow them out with an air compressor. To prevent the jets from clogging in the future make sure to flush all shampoo out of the machine with clean water when done using it. That is most likely your problem.
.
.If it is leaving black streaks on your carpet it could be coming from a burnt belt or melted brushroller part, in which case inspect the belts and brushrollers and replace the damaged pieces.
.
.I hope this helped
.
.Good Luck
.
.Otherwise, The jets on this unit clog easily, there are two of them and you can locate them under the recovery tank towards the front of the machine, and blow them out with an air compressor. To prevent the jets from clogging in the future make sure to flush all shampoo out of the machine with clean water when done using it. That is most likely your problem.
.
.If it is leaving black streaks on your carpet it could be coming from a burnt belt or melted brushroller part, in which case inspect the belts and brushrollers and replace the damaged pieces.
.
.I hope this helped
.
.Good Luck
Read Full Q/A … : Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum
My carpet cleaner (bissell proheat plus) is not steaming, dispensing cleaner. Seems like there’s a little thingy that should be spinning or turning….. When I work a small area of carpet, it just leaves behind dry blobs of carpet gunk like pet hair. I had to use a carpet sweeper to clean up. FYI – I filled the cleaning fluid container and after trying to clean the carpet, it did empty out but the carpet isn’t wet. Any tips? The manual doesn’t help.
ANSWER : You need to replace the pump belt. Here is the belt you need:
Read Full Q/A … : Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum
Hoover WindTunnel Self-Propelled V Belt
ANSWER : I had this same problem with the V belt on my Hoover Vaccuum..
.There are three (3) basic things that will cause the brush roll not to spin..
.1. When handle is upright, brush roll is OFF..2. When switch is set for HARD surface, brush roll is OFF..3. Broken/worn FLAT belt or V Belt, brush roll will not spin.
.
.I noticed that the brush roll was not spinning when my vacuum was set for CARPET. After removing the cover I noticed that the V belt was loose, I thought the belt was worn so I purchased a correct replacement belt and installed it, but the new belt was also loose and when I turned the large flat belt pulley it did not turn the V belt pulley at the same time..
.I double checked the surface setting and I had the vacuum switch set for carpet, but still when I released the handle out of the upright position the brush roll would still not spin..
.My aggravation finally led me to this posting on FixYa’s website..
.The first thing I did was checked the screw to the left of the V belt as suggested by ejmjr5 and this did nothing to solve the problem or create more tension on the V belt, even when the upright handle was not in the upright position..
.After playing around with the surface setting control switch/nob I notice that when I moved the switch out of the HARD surface setting and over to CARPET, I had thought that the switch was set for CARPET as it visually appeared, but I was not pushing the switch over hard enough to click it into the CARPET setting mode..
.VOILA, the brush roll now spins correctly even though the V belt seams to be too loose for the pulley..
.You really have to force the switch into the CARPET setting. Be sure that you hear the switch/nob click into place..
.Now you can effectively clean up after that hangover of a party!.
.Burp!
.There are three (3) basic things that will cause the brush roll not to spin..
.1. When handle is upright, brush roll is OFF..2. When switch is set for HARD surface, brush roll is OFF..3. Broken/worn FLAT belt or V Belt, brush roll will not spin.
.
.I noticed that the brush roll was not spinning when my vacuum was set for CARPET. After removing the cover I noticed that the V belt was loose, I thought the belt was worn so I purchased a correct replacement belt and installed it, but the new belt was also loose and when I turned the large flat belt pulley it did not turn the V belt pulley at the same time..
.I double checked the surface setting and I had the vacuum switch set for carpet, but still when I released the handle out of the upright position the brush roll would still not spin..
.My aggravation finally led me to this posting on FixYa’s website..
.The first thing I did was checked the screw to the left of the V belt as suggested by ejmjr5 and this did nothing to solve the problem or create more tension on the V belt, even when the upright handle was not in the upright position..
.After playing around with the surface setting control switch/nob I notice that when I moved the switch out of the HARD surface setting and over to CARPET, I had thought that the switch was set for CARPET as it visually appeared, but I was not pushing the switch over hard enough to click it into the CARPET setting mode..
.VOILA, the brush roll now spins correctly even though the V belt seams to be too loose for the pulley..
.You really have to force the switch into the CARPET setting. Be sure that you hear the switch/nob click into place..
.Now you can effectively clean up after that hangover of a party!.
.Burp!
Read Full Q/A … : Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum
When selecting the carpet cleaning mode, it appears the belt is slipping (due to the noise) over the drive pulley. How do you access the drive mechanism to replace belt or inspect drive pulley and belt condition?
ANSWER : On those units you must replace the clutch assy. you cant just replace the belt. there is also a special tool used to get the new belts on the brushbar. If you would like me to walk you through this repair let me know.
Read Full Q/A … : Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum
MY VACUUM ISN’T PULLING AS STRONG AS IT USED TO SO I THINK IT NEEDS A NEW BELT. I CAN’T FIND THE MANUEL ON IT SO I NEED SOME INSTRUCTIONS ON HOW TO CHANGE THE BELT. I DON’T WANT TO BREAK MY VAC. CAN SOME ONE PLEASE INSTRUCT ME ON HOW I SHOULD CHANGE THE BELT PLEASE. TYPE VAC: EUREKA THE BOSS WHIRLWIND LITE CYCLONIC POWER CANISTER TYPE VAC. THE HANDLE IS DETACHABLE TO CLEAN IN THE CORNER WITH A SMALL EXTENSION.
ANSWER : You can get Eureka replacement belts here:
Read Full Q/A … : Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum
Bissell Power Track Cyclonic Upright Bagless Vacuum.. ..The spin brush works laying down….when upright it won’t spin! I cleaned any and all hair from the roller….belt is not broken….but do I need a new belt though? The vac is a few years old bever replaced the belt yet.
ANSWER : You need a new belt.
Read Full Q/A … : Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum
