Kirby G4 Bagged Upright Vacuum

How to Identify and Fix Common Vacuum Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :

Instead of depositing soapy water on the carpet, the Kirby Multi-Surface Shampoo System works a thick foam onto the carpet fibers. This scrubs and emulsifies any caked-on dirt and grime. The dirt and thick foam is then collected in the Multi-Surface Shampoo System tray.
Q: What shampoo can I use in my Kirby? A: You should only use genuine Kirby Carpet Shampoo in Kirby shampoo systems. For a fragrance-free option, please try Kirby Unscented Carpet Shampoo!
The Kirby shampoo takes 2 hours to completely dry, at the most. I also noticed that clean-up was a lot easier. The Kirby shampoo rinses away clean with just cold water, taking the dirt with it.
Mixing ratio of 1:10 with warm water of +/- 40 degrees.
Allow the carpet to dry completely. Kirby`s unique shampoo will encapsulate the dirt as it dries so that it can be easily vacuumed away. Once the carpet is dry, convert the Kirby Avalir 2 System back to an upright vacuum and use it to remove any dry residue left over after shampooing.
Kirby vacuum prices are higher than many vacuums found at big-box stores, but that`s because Kirby vacuums are made of durable materials that will last for years. Why replace an inexpensive vacuum over and over again when you can purchase a Kirby vacuum? This complete home cleaning system that will last for a lifetime.
In many cases, using plain water in your carpet cleaning machine is enough to flush out soil and dirt. You can even add a bit of dishwashing detergent to help freshen the carpet. (Dishwashing soap with grease-cutting capabilities can even help remove certain oil-based stains.) Dish cleaners are safe and gentle.
It`s not unusual for DIY carpet cleaners to need eight or even 10 passes on a carpet before the water runs clear. This is especially true when: It has been a long time since your carpet was last deep-cleaned.
Only Vacuum a Dry Carpet

If you vacuum a wet carpet, dirty water could enter the motor and cause damage to it. In severe cases where the carpet is too wet, you could even risk electrocution. Even in a mild scenario, you`d still end up with a soggy mess to deal with when you eventually empty the dust bag.

Your carpet will be only slightly damp to the touch after your cleaning. Most carpets typically need 6-10 hours to dry completely. However, it could take up to 24 hours to dry depending on the time of year your carpets are cleaned, and the air circulation, humidity and temperature in your home.
If you don`t have a carpet cleaning machine, you can still clean your carpet by hand using carpet shampoo or powdered cleaner. If you want a gentler solution, vinegar and baking soda are great DIY options. Whatever you choose, make sure it`s compatible with your carpet`s material.
How Often Should You Shampoo Your Carpet? You should clean your carpet at least every 12 months to remove dirt, grime, and allergens.
For fabric upholstery: Mix 1/4 cup vinegar, 3/4 warm water and 1 tablespoon of dish soap or Castile soap. Put in a spray bottle. Mist the soiled area. Scrub with a soft cloth until the stain lifts.
It is recommended that you try to stay off the freshly cleaned carpets until they are dry – about 6 hours. If you MUST walk over your damp carpet before it is dry use EXTREME caution. Where you transition from carpet to another hard surface, like tile or hardwood, can be very slippery.
Open windows – air flow can help to improve drying times and opening windows can help, unless it is very humid outside. Use floor fans – running floor fans in areas with damp carpet will help to move the humid air created by evaporation out of the space, and dry the carpet more quickly.
You will want to follow the machine directions. So if it has a fill line or formula cup you would use that. Otherwise we suggest using 6 oz of carpet shampoo to a gallon of water. How much product you need depends on how much liquid the machine disperses, how many times the carpet needs to be cleaned, etc.
Recommended dilution on carpets is between 10:1 and 20:1, either in a automated carpet cleaner or by diluting in a bottle and spraying directly to the surface. Once dry the carpet can be vacuumed to complete the process.
– Mix warm water with dry laundry detergent in the ration 10:1. – Pour the solution into the carpet cleaning machine. The solution can get your carpet cleaned without forming any foam in the process.
In a bowl or small bucket, mix one part white vinegar with three parts water. Dip the bristles of the scrub brush into the solution and rub them into the carpet. Massage them into the fibers well (without fully saturating the carpet) and follow up with a cloth to help blot excess moisture.
Most professionals will recommend that you bring in a dehumidifier. This will pull the water out of the padding and help it dry. Keep one corner of the carpet lifted a bit to also direct some airflow under there using a fan. Continue promoting airflow throughout the entire room as much as possible.
The Dyson vs. Kirby vacuum cleaners debate can be complicated, as these brands are so different. If it comes down to price or size, Dyson will probably get the upper hand — but for all other vacuuming considerations, Kirby is the way to go.
This unusual title, which was being developed by DMA Design (who are now Rockstar North — yes, that Rockstar North), the game was meant to use the Super NES Mouse to launch Kirby across the levels, but slow development and poor sales of the mouse caused the project to be cancelled.
Kirby vacuum cleaners are made of die cast aluminum where most other vacuums are made of plastic. This makes the Kirby vacuum more durable than other model on the market. This is why the average lifespan of a Kirby is over 30 years.
Q: It smells like the belt is burning. What is wrong? A:It is likely the belt isn`t turning freely on the brush roll. Flip out the belt lifter handle and turn it clockwise until the green arrows line up.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Electrolux Epic 6500SR Full Bag sensor working, Does not Reset properly
ANSWER : The problem was a sticking switch that was not being reset. The vacuum on/off switch mechanism is comprised of two switches. One is the main switch that turns the vacuum on and off. The second is a shut off switch that gets tripped when the full bag sensor is engaged. This second switch is supposed to get reset when you push the on/off switch on the outside of the machine. The full bag shutoff switch was stiff and it, therefore, was taking a couple of presses of the on/off switch to move the shutoff switch back into the running position.

Read Full Q/A … : Kirby G4 Bagged Upright Vacuum

Dirt devil vacuum cleaner–trouble vacuuming dirt and pet hair on carpeting –is the problem with the spinning brush which contacts the floor,  not contacting the carpeting??  I thought (when I bought this vacuum) that the aforementioned brush was adjustable to various heights of carpeting.  Sometimes, it seems like nothing is being vacuumed up –unless I have just put a new bag on the vacuum… Do I need or can I replace the spinning brush on the bottom of the vacuum so it kicks up and vacuums
ANSWER : Try replacing the belt. Rubber belts stretch out after about a year.

Read Full Q/A … : Kirby G4 Bagged Upright Vacuum

I have a Kirby G4 Vacuum Cleaner – MOdel G4 D. I have never had any problems or repairs done to it in the past ten plus years that I’ve had it. This is an upright vacuum. I was vacuuming the carpet floor and was not having any trouble at all. I switched the vacuum off and moved it into a different room. When I tried to turn on the vacuum, it would not turn on. I checked with different outlets, used both front attachment and hose attachment. Checked the front part of the motor/ spiral case. This
ANSWER : Hello,
.My educated guess is that it’s either the switch or the power cord. Here are a couple of guides to help with diagnosis and repair…
.
.http://reviews.ebay.com/COMMON-PROBLEMS-WITH-THE-KIRBY-VACUUM-TROUBLESHOOTING_W0QQugidZ10000000003800312
.
.http://reviews.ebay.com/REPLACING-THE-POWER-SWITCH-ON-ANY-KIRBY-G-SERIES-VACUUM_W0QQugidZ10000000003752018
.
.Hope this helps!!
.Marci

Read Full Q/A … : Kirby G4 Bagged Upright Vacuum

Unbeknownst to me, someone took the bag out of my Kenmore Progressive vacuum and failed to replace it. I have been vacuuming without a bag for months, and today the vacuum stopped sucking. When I opened up the front to replace the bag, tons of dirt and dust came pouring out. I thoroughly cleaned the vacuum, put in a new bag, but still no sucking power. Just dust coming from the rear vents where one of the filters is. Is the vacuum ruined, or is it a simple solution of buying a new filter?
ANSWER : Sounds like you need to buy a new motor. All that grit and dust will ruin a motor and I’m surprised it lasted as long as it did.
.This is where a vacuum that won’t run without a bag would have been nice. (Aerus for one)

Read Full Q/A … : Kirby G4 Bagged Upright Vacuum

How can i shampoo my carpet with the kirby – Kirby G4 Bagged Upright Vacuum
ANSWER : Hello, gwen

I was trying to help you out here. Maybe this will help some? I was going backto some customers that asked questions in the recent past and even fartherback. It appeared that no one answeredsome of them, So, I thought I would take some of my personal time to see if Ican help. Even though this Informational site may not have your exact model orbrand, this site will help you a lot. Here is a site link about everything you want to know about vacuumcleaners and possibly yours, from repair to trouble shooting it. http://home.howstuffworks.com/vacuum-cleaner.htm

Please if this helped you at all, if you can find the time and in your heart torate my help and some kind words written would be appreciated for my free help, I would appreciate it.

Here is also my direct link to my own pages of other areas of my expertise forother problems you might have in Automotive, Appliance, and Electronics. DropIn anytime for my help.

Thanks, Mike

Read Full Q/A … : Kirby G4 Bagged Upright Vacuum

I purchased a brand new Eureka Pet vacuum, sorry don’t know exact name but it the one that has the self cleaning duster on it. Last night I used the vacuum on my carpet, it was working fine until I accidently sucked up the corner of a scarf that was hanging off a couch. I shut the vacuum off, pulled out the scarf and and resumed vacuuming. Much to my dismay the suction on the vacuum had ceased. Can you tell me if there is a reset button on the vacuum? The vacuum does not appear to be damage
ANSWER : If the motor is running, there should be suction. Possible problems depend on whether it’s a canister or upright and are:
.A clog in the hose, UR or canister. Detach hose. Drop small coin in one end and lift hose causing it to roll out the other. If it does, no clog in hose. Drop same coin into hose opening on power head. If it rolls out, no clog in PN.
.Broken fan blades, UR. Needs to be taken to shop for repair/replacement.
.
.A reset button is for use if the motor isn’t running, so won’t have anything to do with the suction.

Read Full Q/A … : Kirby G4 Bagged Upright Vacuum

While vacuuming the red light for the bag of the vacuum came on and the vacuum stopped. The bag was no where near full so I replaced it with a new bag – same problem. It vaccumes for a minute or then stops with bag light on. It is the correct bag for the machine – so what’s the problem?
ANSWER : I’m assuming this is the Epic 6500 or similar model.
.Detach the hose, turn vacuum on. If it runs, place palm of hand against inport hole. If it shuts off the problem is with either the control valve setting or the control valve assembly itself.
.For cvs, turn dial on top of vacuum all the way to the largest dot, and try above test again. If that doesn’t work, then it’s the CVA. It needs to be cleaned or replaced, which is an in shop job. Fro repair, take it to the nearest Aerus Electrolux store. I recommend a full clean and service to remove any dust/dirt from the motor, fan assembly, and other internal parts.
.
.Another problem, which relates to the dial setting, is that fine dust will quickly clog the pores of the bag, resulting in the machine “thinking” the bag is full. Turning the dial to the proper setting helps get the bag fuller. The middle setting is the normal setting, and is for areas without fine dust and sand.

Read Full Q/A … : Kirby G4 Bagged Upright Vacuum

How do i clean the chromr on kirby g4 vacuum – Kirby G4 Bagged Upright Vacuum
ANSWER : The Kirby is polished aluminum. It is best cleaned with mag wheel polish, and lots of “elbow grease”.

Read Full Q/A … : Kirby G4 Bagged Upright Vacuum