Hoover Windtunnel Turbo Power U4645-930 Vacuum\015 Have bottom off but can’t find where else belt goes. Must be more to remove than what I am able to take off...Need to know what else needs to be removed and how to do it.\015
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
Replacement Brand Designed To Fit Hoover Wind Tunnel Belts 13″ and 15″ Models, Fits: All Wind Tunnel Non-Self Propelled Machines, 3 Belts in Pack.
Description. Package of (1) 38528-034 roller brush belt and (1) 38528-035 power drive belt for Hoover WindTunnel models with the self-propelled feature. Replace these belts every 6 months to ensure optimum performance.
Next to the motor, the belt on your vacuum is just about the most important part of your vacuum. Without the belt to spin the brushroll, most vacuums won`t pick up on carpeting at all! If your vacuum uses a rubber belt, check it once a month for cracks, melting, and especially, slippage.
Because vacuum manufacturers do not share a standardized naming system for vacuum belts, using your vacuum`s model number is the best way to ensure an accurate belt order.
Before you spend your time trying to go back over the same areas, hoping you`ll get it all cleaned up the second time around, check out your brush roll and belt. If you`ve cleaned your brush of any sticky stuff and hair, and it all looks fine, you`re likely dealing with a stretched belt.
Since you`ll likely only replace your serpentine belt once during the life of your car, it`s generally recommended to take your car to a professional mechanic. You can do a lot of damage to your vehicle if you drive on the road with an improperly installed serpentine belt.
Inspect the belt to see if it is broken, stretched out, or out of place. If the cogged belt is broken or stretched out, replace it. If the brushroll is sticking, it will cause too much friction and put too much strain on the belt. Remove the brushroll and clean all hair, string, and lint from the brushroll bearings.
The belt may be broken or worn
If you pick up something sharp or debris gets jammed in the brushes then the belt may snap. Also over time your belt will stretch, so it`s a good idea to change your belt once per year to ensure the cleaner picks up dirt effectively.
We suggest to replace the belt every 3 to 9 months to ensure the performance of vacuum, the 2-Belt design can be easy for you to replace it, order once, last throughout the year.
We suggest to replace the belt every 3 to 9 months to ensure the performance of vacuum, the 2-Belt design can be easy for you to replace it, order once, last throughout the year.
Inspect the belt to see if it is broken, stretched out, or out of place. If the cogged belt is broken or stretched out, replace it. If the brushroll is sticking, it will cause too much friction and put too much strain on the belt. Remove the brushroll and clean all hair, string, and lint from the brushroll bearings.
We suggest to replace the belt every 3 to 9 months to ensure the performance of vacuum, the 2-Belt design can be easy for you to replace it, order once, last throughout the year.
Should the brush not rotate freely there may be debris tangled around the ends of the brush, carefully remove any obstructions or replace the brush with a new one. We recommend that you fit a new belt and brush once per year to keep your Reactive vacuum working efficiently.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
Changing belt
Please advise how to change the belt. I wasn’t the person who took the belt off, didn’t watch. Now it’s just me and the belt. I had 2, but 1st one burnt right off. Apparently I didn’t have in the right spot! don’t want to waste the only other new belt I have. Pictures would be greatly appreciated!!!!!!! Thanks Tammy Can call 920-660-0680
Please advise how to change the belt. I wasn’t the person who took the belt off, didn’t watch. Now it’s just me and the belt. I had 2, but 1st one burnt right off. Apparently I didn’t have in the right spot! don’t want to waste the only other new belt I have. Pictures would be greatly appreciated!!!!!!! Thanks Tammy Can call 920-660-0680
ANSWER : Step 1: Lower handle to floor to change belt
Step 2: Remove the two screws from the top hood on the foot
Step 3: Lift hood to remove
Step 4: Lift right end of brushroll (the belt end)
Step 5: Remove and discard belt.
Step 6: Place new belt around motor shaft.
Step 7: Place new belt around brushroll pulley.
Step 8: Align left end cap with base. Push end cap securely into
place. Make sure the square on the brushroll cap is in
place
Step 9: Pull right side of brushroll to stretch belt. Secure right
end cap into base.
IMPORTANT
Step 10: Rotate brushroll by hand several full rotations to properly
position belt.
Step 11: Place hood back on cleaner. Replace and tighten
two screws.
Step 12: Return vacuum to upright position.
Step 2: Remove the two screws from the top hood on the foot
Step 3: Lift hood to remove
Step 4: Lift right end of brushroll (the belt end)
Step 5: Remove and discard belt.
Step 6: Place new belt around motor shaft.
Step 7: Place new belt around brushroll pulley.
Step 8: Align left end cap with base. Push end cap securely into
place. Make sure the square on the brushroll cap is in
place
Step 9: Pull right side of brushroll to stretch belt. Secure right
end cap into base.
IMPORTANT
Step 10: Rotate brushroll by hand several full rotations to properly
position belt.
Step 11: Place hood back on cleaner. Replace and tighten
two screws.
Step 12: Return vacuum to upright position.
You can also download your user manual here which has instructions on how with diagrams
Read Full Q/A … : Hoover Windtunnel Turbo Power U4645-930 Vacuum
Windtunnel belt I have a new Hoover Windtunnel canister. The belt keeps coming off. It happened a couple weeks ago (several times after putting the belt back on) so I assumed I might need a new belt as it might have dried out at the store. I ordered new belts and today I used it for about an hour and the belt came off again, twice. There doesn’t seem to be anything to hold the belt on the stem as it seems to slip off. I have tried it centered, to the left and to the right….can you help. I am v
ANSWER : I’ve successfully used a compatible belt – Royal 104425001 .It’s still new, but for the time being at least – it works.
Read Full Q/A … : Hoover Windtunnel Turbo Power U4645-930 Vacuum
Hoover WindTunnel Self-Propelled V Belt
ANSWER : I had this same problem with the V belt on my Hoover Vaccuum..
.There are three (3) basic things that will cause the brush roll not to spin..
.1. When handle is upright, brush roll is OFF..2. When switch is set for HARD surface, brush roll is OFF..3. Broken/worn FLAT belt or V Belt, brush roll will not spin.
.
.I noticed that the brush roll was not spinning when my vacuum was set for CARPET. After removing the cover I noticed that the V belt was loose, I thought the belt was worn so I purchased a correct replacement belt and installed it, but the new belt was also loose and when I turned the large flat belt pulley it did not turn the V belt pulley at the same time..
.I double checked the surface setting and I had the vacuum switch set for carpet, but still when I released the handle out of the upright position the brush roll would still not spin..
.My aggravation finally led me to this posting on FixYa’s website..
.The first thing I did was checked the screw to the left of the V belt as suggested by ejmjr5 and this did nothing to solve the problem or create more tension on the V belt, even when the upright handle was not in the upright position..
.After playing around with the surface setting control switch/nob I notice that when I moved the switch out of the HARD surface setting and over to CARPET, I had thought that the switch was set for CARPET as it visually appeared, but I was not pushing the switch over hard enough to click it into the CARPET setting mode..
.VOILA, the brush roll now spins correctly even though the V belt seams to be too loose for the pulley..
.You really have to force the switch into the CARPET setting. Be sure that you hear the switch/nob click into place..
.Now you can effectively clean up after that hangover of a party!.
.Burp!
.There are three (3) basic things that will cause the brush roll not to spin..
.1. When handle is upright, brush roll is OFF..2. When switch is set for HARD surface, brush roll is OFF..3. Broken/worn FLAT belt or V Belt, brush roll will not spin.
.
.I noticed that the brush roll was not spinning when my vacuum was set for CARPET. After removing the cover I noticed that the V belt was loose, I thought the belt was worn so I purchased a correct replacement belt and installed it, but the new belt was also loose and when I turned the large flat belt pulley it did not turn the V belt pulley at the same time..
.I double checked the surface setting and I had the vacuum switch set for carpet, but still when I released the handle out of the upright position the brush roll would still not spin..
.My aggravation finally led me to this posting on FixYa’s website..
.The first thing I did was checked the screw to the left of the V belt as suggested by ejmjr5 and this did nothing to solve the problem or create more tension on the V belt, even when the upright handle was not in the upright position..
.After playing around with the surface setting control switch/nob I notice that when I moved the switch out of the HARD surface setting and over to CARPET, I had thought that the switch was set for CARPET as it visually appeared, but I was not pushing the switch over hard enough to click it into the CARPET setting mode..
.VOILA, the brush roll now spins correctly even though the V belt seams to be too loose for the pulley..
.You really have to force the switch into the CARPET setting. Be sure that you hear the switch/nob click into place..
.Now you can effectively clean up after that hangover of a party!.
.Burp!
Read Full Q/A … : Hoover Windtunnel Turbo Power U4645-930 Vacuum
The original belt on my upright Kenmore Progressive broke and I replaced it with the spare that was in the vacuum. The vacuum and spare belt are about 10 years old. Then the spare broke after one vacuuming session and there was a burning smell coming from the vacuum. I ordered new belts and replaced it with the new belt. It seems to be working fine with no smell. I checked the belt after I vacuumed the family room and although it was in tact, the belt was very hot. Is that normal? Should t
ANSWER : The belt heats up due to the friction, as well as being in contact with the shaft of a hot motor. It is normal.
Read Full Q/A … : Hoover Windtunnel Turbo Power U4645-930 Vacuum
I’m using (or WAS using) a Eureka ”the boss” model 8803. The belt broke, no biggie, so I replaced it with a Eureka model U belt, the problem is when I put the new belt on and turn on the vaccuum, the belt breaks again. I am also having trouble getting the brush roller to fit right when the belt is in place. I can’t find any sharp edges that would cut the belt,nor can I find where any small bits may have broken. Anyone have a solution for me?
ANSWER : First, make sure you have the right belt, second, i am thinking that you are not lineing the roller up right, it will only fit one way. look at the ends of the roller and the grooves where it slides in, you should be able to see clearly how it goes.
Read Full Q/A … : Hoover Windtunnel Turbo Power U4645-930 Vacuum
Hi my proheat bissell 7901 stopped pumping water to the floor, but it pumps water from the hand hose. I read the manual and followed how to check belt and the flat belt on right side of shampooer is fine and I turned on and it turns and so do the brushes at the bottom of the machine. I was reading online and I guess there’s two belts on this machine? where can I find the other belt to see if it needs replacing. I guess it’s a ribbed belt? that is the water pump belt?
ANSWER : Just taken ours apart with the same problem… found it was caused by the 2 halves of the main casing coming apart in the area where the upright pedal release is. I found this to be due to the upper casing having broken in 2 places – the bottom of the screw wells..This means that the water tank cannot exert sufficient pressure on the valve to release the water..Only solution is a new top cover assembly
Read Full Q/A … : Hoover Windtunnel Turbo Power U4645-930 Vacuum
Is there any way to repair or replace the belt GUIDE on the inside of the belt compartment of a ’97 Hoover Wind Tunnel (not self-propelled)? It became twisted when a belt broke and now the belt rubs against it and sounds really weird, and I’m sure new belts will continue to break.. This guide is a long piece of molded material (part of the compartent wall) to keep the belt from coming off the pulley. It also had a sort of metal clip on it. It was loose and I took it off because of the way the pa
ANSWER : Honestly you should take it to a vac.shop they can fix any vac.
Read Full Q/A … : Hoover Windtunnel Turbo Power U4645-930 Vacuum
Changing the belt
ANSWER : Just in case you’re still having this problem…. you don’t need to fit the belt around the motor shaft. Only wrap it around the brush roller and the piece near the back that you are able to put the belt around, and snap the brush back into place. It didn’t look like it would work (it looked like my cat could have done the same thing and gotten the same result) but it works gloriously now!
Hope this helps.
Read Full Q/A … : Hoover Windtunnel Turbo Power U4645-930 Vacuum
