Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

How to Identify and Fix Common Vacuum Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :

Switch off and unplug before emptying the clear bin. To remove the cyclone and clear bin unit, push the red button on the top of the carrying handle, as shown. To release the dirt, firmly push the red bin release button.
Emptying the bin

Remove the bin by pressing the release button to the side of the carry handle. To release the dirt, press the red bin release button. To minimise dust/allergen contact when emptying, encase the clear bin tightly in a plastic bag and empty.

The Dyson DC07 was introduced in 2001 with brand new Root Cyclone technology.
There are two filters on a DC07, the first is the pre-motor filter, which are washable and is recommended by Dyson to be washed at least every 6 months. The pre motor filter also acts as a protection to the motor, trapping the smallest of dirt or debris from travelling to the motor.
Depending on your Dyson model, you may be surprised by the amount of dust and debris you`ll find inside it. So, `detach the hose from the wand, then clean its insides using a cloth pushed inside with the help of a broomstick or anything similar.
Empty the bin

To release the dirt, hold the appliance by the handle, pull the red lever back and lift upwards. Continue until the bin base automatically opens and releases the dirt. Once the dirt is released, push the cyclone back down until it clicks. Close the bin base of the machine ensuring it clicks in to place.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

How do i empty my dyson dc07 – Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
ANSWER : Hi its Darran at Dyson.

Remove the bin and cyclone assembyl by pressing the release button above the word Dyson on the carrying handle towards the machine.

Then hold the bin and cyclone assembly over a dustbin and pull the trigger located underneath the carrying handle which will release the bin base to empty the dust and debris from the bin.

I hope this information is useful to you and should you need any further help or advice, please contact our Helpline on 0800 298 0298 (UK) or 1866MYDYSON (US).

Kind regards
Darran
Dyson Customer Service

Replace belt on dyson animal – Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Why does my dyson DC07 not **** anymore ? – Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
ANSWER : Hi its Darran at Dyson.

If you are experiencing a drop in performance, please follow the full diagnostics outlined in the support section on our website at www.dyson.com.

If this does not resolve the issue, please contact our Helpline on 0800 298 0298 (UK) or 1866MYDYSON (US).

Kind regards

Darran
Dyson Customer Service

Dyson Animal is not powering up – Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
ANSWER : It might be the eletrical inside the machine.or even the power cord.

How to put new cable on dyson dc07 upright – Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum
ANSWER : Have a look at www.dysonmedic.com which has some excellent info on your machine.

Dyson animal beater bar not working – Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
ANSWER : Is the belt ok that drives it , is the clutch ok this video will give you instructions how to fix

Replace power cord on Dyson DC07 – Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
ANSWER : The following link will take you to an article on how to change the motor on a DC07. Look at photos 4, 5 and 6 which shows how to disconnect the power cord.
.
.http://www.dysonmedic.com/DC07%20Folder/DC07%20Motor%20change.html
.
.Reassemble by reversing dissassembly instructions.

Dyson vacuum turned off while vacuuming – Dyson DC07 Bagless Upright Cyclonic Vacuum
ANSWER : Hi There,
Assuming if you leave it for an hour and come back to it that it works again you have an airflow issue. This machine will cut out if the motor gets too hot. The likely causes are 1. Filters – take them out and give a good clean once dry you can try them again. 2. Blockage – Remove your u-bend and the blockage removal access check for an obstruction.3. Radix assembly is blocked. I will post a link to a YouTube video showing how to address this as it is a bit more difficult.
If your machine wont turn back on after a rest then your options are 1. Cord problem (most likely)2. Switch (unlikely)3. Motor

I have a video for just about all these problems on my youtube channel under VacuumSpot or VacuumSmart. If this is a step in the right direction please lay a thumbs up on the videos 🙂

If you need parts for your dyson in Australia check out VacuumSpot