dyson dcwill not run.

How to Identify and Fix Common Vacuum Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :

If your dyson vacuum isn`t turning on, don`t panic – there are a couple possible causes. It could simply be that the vacuum overheated and shut itself off. If that is the case, wait 24 hours and turn it back on. However, another problem with dysons are failed power switches.
Most cases of a jammed or stuck brush bar are quick and easy to fix, simply pulling the debris gently from the brush bar. Alternatively, if you need to clear a problematic blockage, you can take the brush bar out of the housing easily, for quick maintenance.
Dyson will repair your machine in accordance with Dyson service and warranty terms and conditions. If your machine is under warranty, Dyson will perform repairs under the terms of such warranty, provided you have presented satisfactory proof of the machine`s eligibility for repairs.
Checking for blockages

It may be full, or the machine may simply perceive it as too full to continue working. Dyson vacuum cleaners require constant airflow through them to work, and a full bin can stop this from happening. Make sure there`s no dirt lodged in the top part of the bin.

When your Dyson no longer powers on even after charging the most likely cause is a damaged battery. This means the battery will no longer hold a charge and will need to be replaced. Once a new battery is purchased you can learn how to replace it by visiting our battery replacement page here.
It`s possible there`s a power consumption issue, with there just not being enough residual charge to run the machine. A new battery should fix this. My other thought is that it`s overheating. If too much power is pushed through the motor, which MAX power does, it could stop after a few seconds if it become hot.
If the vacuum is not plugged into its power outlet correctly, it will not turn on. Check to make sure that the vacuum`s electrical cord is completely plugged into the outlet. Additionally, the power outlet could be a problem.
To reset the Brush bar press the Brush bar control button twice or switch the machine off and back on.
Check that the vacuum cleaner is plugged into a working power outlet and that fuses and breakers don`t need resetting. An activated thermal cut-out due to a blockage is the next most likely cause of the problem. Check for blockages in the hose and filters, and remove any obstructions that you find.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

My Kirby G3 diamond series won’t turn on
ANSWER : Hi There, The most common problem by far is that the cord is faulty. This is a pretty easy repair to do at home. If your machine was randomly cutting out before it stopped altogether then the cord is likely the culprit. If however it stopped all of a sudden with no warning then it is possibly a switch or motor issue which is a much harder repair to achieve for a novice.
The kirby cords are not terribly expensive (and I have linked a how to video showing how its done) so if you need a new one I would say DIY is the go, otherwise spend the $25 get a pro to take a look.

Read Full Q/A … : dyson dc

Can i fix or who would fix power cord to my vaccum
ANSWER : Get you some electrical tape and strip and connect the proper wire colors back. But be sure to tape each wire very well before you continue to the next. After that just tape all together.

Read Full Q/A … : dyson dc

Need to fix level control part b-0133260 on bissell 7901-1 need to know how to fix it
ANSWER : Hi,

Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.

Bissell Proheat Upright Wet/Dry Vacuum Problems

heatman101.
.hgjd

Read Full Q/A … : dyson dc

I was replacing the belt on my Eureka Smartvac 4870 and one of the felt gaskets (or part of it) popped out. I thought I put it in correctly, but the first I used it after replacing the belt, the gasket got mangled by the brush. I’m wondering how important it is to get fixed; is it a part I can pick up anywhere and fix myself? Thanks for the help.
ANSWER : I’m no expert but if you mean the felt on the roller, you have to replace the roller (expensive,esp. for such a minor part). So. I found some felt with adhesive in the craft section at Wal-Mart, trimmed it to fit and done deal. Felt reduces friction.

Read Full Q/A … : dyson dc

How do I fix the scooba comes up with service error does its 4 tone followed by 2 beeps I looked it up and it says vacuum Malfunction is their ways to fix it
ANSWER : Here you go try this out.

http://www.manualslib.com/manual/284388/Irobot-Scooba-5900.html?page=10

Read Full Q/A … : dyson dc

My electrolux Epic 6500 power nozzle Model N109J will not work. It had an intermittent short which I thought I fixed (some of the insulation on the wires were pinched). I fixed the wires and it worked intermittently for an hour then shut down completely. Could the reset switch have a short? When I press the switch nothing happens.
ANSWER : The switch is definitely a possibility, but other problems can also cause this.
.Bad switch, needs replaced.
.Broken wiring in power nozzle, wands, hose, or canister.
.Bad PN motor.
.
.I strongly recommend taking it to the nearest authorized Aerus Electrolux store for a diagnosis (should be free). Allowing them to do any repairs necessary is recommended, as well. This will ensure it’s done correctly.
.
.http://www.aerushome.com/storelocator/

Read Full Q/A … : dyson dc

It no longer stands upright as a 1 inch piece of arched plastic broke off. Is there a replacement part? what does it entail to fix it? Is it worth fixing?
ANSWER : Mine did the same thing.To date I have yet to find a replacement part.I do not think it is all that important either.And most likely not worth your time.

Read Full Q/A … : dyson dc

My Hoover vacuum is not vacuuming the carpets or floors. When I release the tube to use the smaller end the suction works perfect. So i believe the problem is in the rods on the floor or in the part that vacuums the floor! Can you tell me how to fix it , or where can I take it to get it fixed?

thanks

ANSWER : Ive just had the exact same problem. In the very back lower portion of the vacuum You will need to take it apart. I guarantee there is a clog. You might also check your belts to make sure they are still on track.

Read Full Q/A … : dyson dc