Shark navigatorRoller is locked followed the direction to get it unlocked did. Not work

How to Identify and Fix Common Vacuum Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :

In the ION P50, there is a release latch on one side of it with an “eject roller” written. Gently push it forward to release the roller. Make sure to have the nozzle low to the ground or have another hand to catch it, so it doesn`t drop to the ground. Once you push the lever, the roller pops out.
If you checked your brush roll, floor setting, and belt but your brush roll is still not spinning, that means you probably need a Shark micro switch replacement. This small switch tells the vacuums brush when to start spinning.
To reset your shark vacuum, put the Power button in the On-Off position and keep the vacuum unplugged. If necessary, clear the hose. Once it has cooled completely, plug the vacuum back in again.
If the roller brush is not spinning, it cannot pick up dust. One reason could be that the power button is not set to position II, which runs the roller brush. If the button does not work, here is the link to the power button replacement guide. Another reason is that the roller brush could be broken.
Press the Eject Roller button to detach the small roller. Pull the roller away from the vacuum to remove it.
Some attachments may have a “Release” button–if so, hold down the button while sliding the attachment off. The back of the vacuum has slots to hold up to two vacuum attachments. To store, simply place the attachment onto the circular slots.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

I can’t get the vacuum to **** and can’t get to the point of the clog. The pieces don’t come off. Also need to know how to get the filter piece off the machine.
ANSWER : This link is for the manual
http://www.dysonmedic.com/PDF%20docs/dyson_dc18_owners_manual.pdf

Read Full Q/A … : Shark navigator

Can’t get it from Roller Brush Off to Roller Brush On
ANSWER : On some model there is also a plastic tab to unlock the roller brush, check it out. You must also have the right tool installed.

Read Full Q/A … : Shark navigator

I have an old upright hoover vacuum. I need to change the belt but can’t figure out how to get to it. The bottom plate over the roller brush comes off but I can’t get anything else off to get to the other end of the belt.
ANSWER : Model no. req

Read Full Q/A … : Shark navigator

My Hoover Windtunnel Mach 6.9 brush roller quit working. Upon investigating I found that the idler arm pulley was broken so I managed to replace that. Before putting the cover back on I see the control knob for the roller brush moves a plastic piece left or right to activate/deactivate the brush roller. I don't know where this plastic piece connects. It appears to me that the idler are when raised creates tension on the belt which drives the roller. I'm at a loss trying to figure ou

I have a Kirby G series diamond edition. There seems to be no suction when I turn on the vaccum. The bag inflates, but the roller does not turn. It has a new belt and the roller brush is clean. Any suggestion on what I might do to increase the suction and get the roller bar moving?
ANSWER : THE IMPELLER LOOKS SHOT.. 25 QUID FOR NEW ONE,,LIFT THE LID AND TURN THE ROUND PIN AND CHECK FOR RIDGES ROUND THE WHITE IMPELLER,,IF NONE THERE THATS IT,, HAPPEND TO ME TEN MINS TO FIX GEORGE

Read Full Q/A … : Shark navigator

I am trying to replace my vacuum belt and can not get the roller brush to fit back into the slot after I put the belt back onto one end of the roller brush. Am I reassembling the belt and roller brush the right way?
ANSWER : If its a hoover or bissell, one side of the brushroll is slotted and slides. if its a eureka the hexagon end caps must be properly aligned, they go in at an angle. if its none of these provide me with the make and model # and i will give you a detailed description on installation. let me know if you need more help.

Read Full Q/A … : Shark navigator

My bissell 6590 works fine with hose attachment. Motor shaft turns when belt and roller are off. When belt and roller are on it’s noisy and smelly. Now one end of the roller actually melted in the holding slot. Do these rollers wear out like this or should I be looking for another problem.
ANSWER : Replace the roller,belt and before instalation clean motor shaft where belt rolls. you can turn on the vacumm and using a knife scrape the motor shaft from the black dirt.

Read Full Q/A … : Shark navigator

The belt wont turn…i cant get in to the inside to check to see if the belt isnt on the roller…how do i get up in there..i took the bottom plate off and you still cant get inside…
thx
Peggy
ANSWER : The following site has some great info on your machine:.
.www.dysonmedic.com

Read Full Q/A … : Shark navigator