Dyson DC07 Bagless Upright Cyclonic Vacuum\015 IT JUST STOPED\015

How to Identify and Fix Common Vacuum Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :

If there is a strong burning smell coming from the motor area of your Dyson DC14 or DC07 then it is most likely that your motor has burnt out.
It may be full, or the machine may simply perceive it as too full to continue working. Dyson vacuum cleaners require constant airflow through them to work, and a full bin can stop this from happening. Make sure there`s no dirt lodged in the top part of the bin.
The Dyson DC07 was introduced in 2001 with brand new Root Cyclone technology.
If your dyson vacuum isn`t turning on, don`t panic – there are a couple possible causes. It could simply be that the vacuum overheated and shut itself off. If that is the case, wait 24 hours and turn it back on. However, another problem with dysons are failed power switches.
Check the LED light to determine the battery level. A solid blue light indicates that the machine is in normal operating mode. A flashing blue light indicates that there is no power, and the battery needs to be charged for a minimum of 3.5 hours.
If all you hear from the vacuum unit is a click at the when you try to start the vacuum motor from inside the house, then the motor in the unit is dead and has to be replaced. A strong odor from the shellac, which coats the copper coil windings, is an indicator that the motor is about to or has burnt out.
Over time, all batteries are subject to degradation. So if your run time has declined when the machine is not in Max / Boost mode, it might be time to buy a new battery. All our machines come with a 2-year initial warranty that includes the battery.
It`s possible there`s a power consumption issue, with there just not being enough residual charge to run the machine. A new battery should fix this. My other thought is that it`s overheating. If too much power is pushed through the motor, which MAX power does, it could stop after a few seconds if it become hot.
The DC07 had a long production run from 2001 until 2008, and came in many different colour combinations.
Check that the vacuum cleaner is plugged into a working power outlet and that fuses and breakers don`t need resetting. An activated thermal cut-out due to a blockage is the next most likely cause of the problem. Check for blockages in the hose and filters, and remove any obstructions that you find.
To reset the Brush bar press the Brush bar control button twice or switch the machine off and back on.
In many cases, you probably can repair a Dyson yourself, especially when it comes to common issues (see below). However, even if your machine needs some extra TLC by a Dyson expert, it can be worth getting it repaired.
If your Dyson machine isn`t working properly, please visit our Troubleshooting page where we may be able to help you fix it, or where you can purchase replacement parts. If our Troubleshooting steps have not resolved the problem with your Dyson machine, we can arrange for a repair.
If the motor on your Dyson vacuum is faulty, it will need replacing. The video and step by step guide below will take you through your Dyson motor replacement.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Need instructions how to use Hoover Steam Vac Spin Scrub. I borrowed it from my Sister and she left it with no instruction book or letting me know how to operate it. I put water & cleaner in top tank. That’s all I know to do. Do I put any water in bottom tank? I figured not, since that is probably where the water goes when sucked up by vac. Do I leave lid on bottom tank? I usually use a commercial cleaner, and this is very different. I need to know NOW, as I must return it to her today, and I’m
ANSWER : I did have a solution in just a few minutes. Someone responded with a solution that gave me the website where I could go and print the manual in pdf, so did that, and checking instructions I was able to clean my carpets and get the shampooer back to my sister later the same day. I really appreciated your site and help I got for my problem. I found it on google. Thanks again!
.
.[email protected]

Kirby Sentria I bought my kirby sentria just before we were to move house and although I have the instructions somewhere, they will be boxed up and I so want to clean the carpets before I move. Problem is that I don’t know whether the belt should be on or off when using the big silver front with the Kirby insignia on it. I know that the green light should come on when it is working properly and it does not, so I am doing something wrong. I can attach the attachments no problem but I want to use
ANSWER : If the green light is off, then its time to replace the band. This video shows you how.

I have a Eureka Boss Model 411… I need to know where the reset button is for the suction motor. The canister was clogged on the backside, I didn’t see it and the suction motor shut off. I have cleared the obstruction, but don’t know where the reset is for that motor. I know how to reset the brush head motor.
ANSWER : If your vacuum motor overheats, it will stop working. it will start working again once it cools.

Owner/user manual Before my sister died she gave me the little grren machine model 1425 turbo brush with heat. That is all I know about it as she did not find the manual and now no one knows where it is and I really want to get it working and learn about it, as I know she loved it. so I really need a manual. thank any one that can tell me if it is on line or something.

Kirby Seems like you know alot about the Kirby. I know how to use my Sentria (unlike these other idiots) but I keep screwing up the shampoo tray assembly. The brush snaps into the tray just fine but the tray doesn’t really stick to the head. It detaches when pushing and pulling the unit. And who knows where that cover goes? It say ‘push here to open’
ANSWER : Machine will not come on

My hoover belt keeps burning when i replace it. i dont have the manual so i dont know what im doing wrong.
ANSWER : Probably when you close it back together, there is a piece rubbing against that you do not see right away but could maybe hear it.

Intele Clean It is constantly in the red. I changed my bag and still its in the red I vacumed in one spot for 20 min, Whats Wrong?
ANSWER : Every time you change the bag you should clean the eye. The eye.is inside the tube behind the bag collar. Just use a lint free.cloth and wipe all around inside the tube. That worked for me!

D.d vaccum i have a dirt devil dynamite…i bought a new for it i put it on and not even 1 minute of using it the belt broke again!!!!i dont know whats going on do i have 2 put it on a certain way does it need grease or what!
ANSWER : Did you check the brush roll, if the ends aren’t turning freely, then it needs to be replaced also.