Hoover U6311-930 Power Drive Bagged Upright Vacuum

How to Identify and Fix Common Vacuum Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :

Simple: the bag or canister is full and the vacuum has nowhere to store the dust it is collecting. Empty the canister or bag. If that doesn`t fix it, the vacuum filter needs to be cleaned or changed.
The most common cause of loss of suction is that the filters have become blocked. They may require cleaning or replacing. Another cause could be that the vacuum cleaner hose is blocked.
Clog located in the vacuum hose

Turn the unit on and feel the suction at the end of the hose handle. If there is no or low suction, then the clog is in the hose. You can remove the clog by running a long, stiff object through the hose, such as a butter knife, starting at the wall end.

Any fine dust remaining in the filter can usually be removed with a gentle rinse under a cold tap – hold the filter under the running water until the water runs clear. You shouldn`t need to use any detergent – just water.
Empty the vacuum cleaner, discard the contents in the outside trash and use an anti-bacterial wipe to clean the vacuum. Let it dry thoroughly. If your manufacturer says your vacuum cannister is washable, wash it out with warm, soapy water and then rinse it and let it dry.
Vacuum cleaners are fairly simple machines. They need power to be transmitted to the vacuum to create a suction force that lifts debris. So, the usual areas that cause suction loss include the wrong height setting, stuck rollers, a faulty gasket, a broken vacuum belt, a filled bag, or a clogged hose.
Check for a plugged hose:

Plugged vacuum hoses are sometimes the reason for a loss in suction. Hoses can get clogged with hair, dust bunnies, string, or anything else that can`t pass through the other end of the hose. Airways inside the machine should be looked at as well. Wherever there is an air passage, check it.

Grab the clog with a pair of needle-nose pliers and pull it out. Open a pair of needle-nose pliers and feed it into the end of the lower hose. Once you feel the clog, pinch the blockage with your pliers to get a good grip on it. Pull the clog out of the hose and throw it away.
Check the hose for any clogs

If your Shark vac has a hose, feel along the length for any lumps. That indicates a clog that`s causing your suction issues. See if you can break the clog by applying gentle pressure with your hands, or gently move it to the end of the hose to remove it.

Your filters get clogged with bacteria, dust, smoke, mold, and other particles. These can all affect the air quality in your home as well as the performance of your vacuum`s cleaning abilities, if the filter is clogged you will find the suction and general performance of your vacuum will be minimized.
We have two possible ways of adjusting the pressure in a vacuum system: first, by changing the pumping speed (altering the speed of the pump or throttling by closing a valve); second, through admission of gas (opening a valve).
All vacuum cleaners operate based on air flowing from the opening at the cleaning head or tool, through the vacuum cleaner and the bag and/or filter system and then out the exhaust port. This airflow is created by the vacuum motor, which also may be referred to as the suction motor.
Clog located in the vacuum hose

Turn the unit on and feel the suction at the end of the hose handle. If there is no or low suction, then the clog is in the hose. You can remove the clog by running a long, stiff object through the hose, such as a butter knife, starting at the wall end.

If your vacuum cleaner has lost suction power, it`s time to empty the container. Vacuum cleaners come with various foam or mesh filters. These might get clogged over time if not cleaned or replaced properly. This will cause your vacuum to lose suction.
If your vacuum cleaner has lost suction power, it`s time to empty the container. Vacuum cleaners come with various foam or mesh filters. These might get clogged over time if not cleaned or replaced properly. This will cause your vacuum to lose suction.
Check for a plugged hose:

Plugged vacuum hoses are sometimes the reason for a loss in suction. Hoses can get clogged with hair, dust bunnies, string, or anything else that can`t pass through the other end of the hose. Airways inside the machine should be looked at as well. Wherever there is an air passage, check it.

If your vacuum cleaner has lost suction power, it`s time to empty the container. Vacuum cleaners come with various foam or mesh filters. These might get clogged over time if not cleaned or replaced properly. This will cause your vacuum to lose suction.
Check that the vacuum cleaner is plugged into a working power outlet and that fuses and breakers don`t need resetting. An activated thermal cut-out due to a blockage is the next most likely cause of the problem. Check for blockages in the hose and filters, and remove any obstructions that you find.
Check that the vacuum cleaner is plugged into a working power outlet and that fuses and breakers don`t need resetting. An activated thermal cut-out due to a blockage is the next most likely cause of the problem. Check for blockages in the hose and filters, and remove any obstructions that you find.
Check for a plugged hose:

Plugged vacuum hoses are sometimes the reason for a loss in suction. Hoses can get clogged with hair, dust bunnies, string, or anything else that can`t pass through the other end of the hose. Airways inside the machine should be looked at as well. Wherever there is an air passage, check it.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Electrolux Epic 6500SR Full Bag sensor working, Does not Reset properly
ANSWER : The problem was a sticking switch that was not being reset. The vacuum on/off switch mechanism is comprised of two switches. One is the main switch that turns the vacuum on and off. The second is a shut off switch that gets tripped when the full bag sensor is engaged. This second switch is supposed to get reset when you push the on/off switch on the outside of the machine. The full bag shutoff switch was stiff and it, therefore, was taking a couple of presses of the on/off switch to move the shutoff switch back into the running position.

Unbeknownst to me, someone took the bag out of my Kenmore Progressive vacuum and failed to replace it. I have been vacuuming without a bag for months, and today the vacuum stopped sucking. When I opened up the front to replace the bag, tons of dirt and dust came pouring out. I thoroughly cleaned the vacuum, put in a new bag, but still no sucking power. Just dust coming from the rear vents where one of the filters is. Is the vacuum ruined, or is it a simple solution of buying a new filter?
ANSWER : Sounds like you need to buy a new motor. All that grit and dust will ruin a motor and I’m surprised it lasted as long as it did.
.This is where a vacuum that won’t run without a bag would have been nice. (Aerus for one)

How do I make my vacuum get unclogged – Hoover U6311-930 Power Drive Bagged Upright Vacuum
ANSWER : Hi,
Here is a tip that I wrote about my Bissel but I bet you have the same problem and the hose is clogged…

Bissell Bagless Upright Vacuum not working
http://www.fixya.com/support/r4387950-bissell_bagless_upright_vacuum_not

heatman101

Suction problem I have a Hoover Widepath Fold Away, 12 amp motor vacuum cleaner and the problem I am having is every time I vacuum, the vacuum gets clogged up with carpet. I am probably only able to do one stroke then it gets clogged and I have to stop and unclog it or it spits it out on the carpet. This is very frustrating and I don’t get much vacuuming done. Please can you help me. Thank you. Gwen email is [email protected]
ANSWER : Get rid of the carpet its shredding and falling apart.no sence in vacuuming old rotten carpet.or try using a vacuum without a brush roller and just suction

Was using my Miele Champagne vacuum, powered down, changed the bag, and now I have no power. I checked to make sure all lids were securely closed, still no power. Checked to make sure outlet was working, still no power…help.
ANSWER : Most likely the cord went bad, one side of it opened up, you will have to replace the cord reel asm. if this is the problem, Could also be a switch, electronic control or the motor.

While vacuuming the red light for the bag of the vacuum came on and the vacuum stopped. The bag was no where near full so I replaced it with a new bag – same problem. It vaccumes for a minute or then stops with bag light on. It is the correct bag for the machine – so what’s the problem?
ANSWER : I’m assuming this is the Epic 6500 or similar model.
.Detach the hose, turn vacuum on. If it runs, place palm of hand against inport hole. If it shuts off the problem is with either the control valve setting or the control valve assembly itself.
.For cvs, turn dial on top of vacuum all the way to the largest dot, and try above test again. If that doesn’t work, then it’s the CVA. It needs to be cleaned or replaced, which is an in shop job. Fro repair, take it to the nearest Aerus Electrolux store. I recommend a full clean and service to remove any dust/dirt from the motor, fan assembly, and other internal parts.
.
.Another problem, which relates to the dial setting, is that fine dust will quickly clog the pores of the bag, resulting in the machine “thinking” the bag is full. Turning the dial to the proper setting helps get the bag fuller. The middle setting is the normal setting, and is for areas without fine dust and sand.

Dirt devil vacuum cleaner–trouble vacuuming dirt and pet hair on carpeting –is the problem with the spinning brush which contacts the floor,  not contacting the carpeting??  I thought (when I bought this vacuum) that the aforementioned brush was adjustable to various heights of carpeting.  Sometimes, it seems like nothing is being vacuumed up –unless I have just put a new bag on the vacuum… Do I need or can I replace the spinning brush on the bottom of the vacuum so it kicks up and vacuums
ANSWER : Try replacing the belt. Rubber belts stretch out after about a year.

Won’t start. My son was using the vacuum & Didn’t change the bag. The vacuum was making the full bag smell, but the light was’t on & it didn’t stop. I stopped him, changed the bag, checked the filter, closed the compartments & turned on the vacuum. Nothing happened. I checked to be sure that it was plugged in, that wasn’t the problem. I’ve let the vacuum “rest” for several days, It still won’t start. Any suggestions?
ANSWER : There is a reset button at the back of the powerhead. The user manual can be downloaded from the electrolux website, although I didn’t find it very useful. There was some info on how to change the powerhead drive belt.