Vacuums\015 I need to change vacuum motor\015

How to Identify and Fix Common Vacuum Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :

This genuine Dyson vacuum part is the reset switch for the Dyson DC24 and D25 uprights. This switch needs to be activated if you experience a power surge while vacuuming, and your vacuum turns off as a result.
Dyson motors are typically robust. Unless you do something crazy like use the max setting exclusively, it should exceed past the two-year manufacturer warranty. But in case the inevitable happens and the motor burns out, replacing it is simple. Fortunately, the process is simple, with simple tools like a screwdriver.
Vacuum cleaners are fairly simple machines. They need power to be transmitted to the vacuum to create a suction force that lifts debris. So, the usual areas that cause suction loss include the wrong height setting, stuck rollers, a faulty gasket, a broken vacuum belt, a filled bag, or a clogged hose.
Full-sized upright vacuum. Ball technology allows you to turn on a dime. Quick-draw telescope reach wand expands for easy high-reach cleaning. Patented Root Cyclone technology cleans all floor surfaces.
To reset the Brush bar press the Brush bar control button twice or switch the machine off and back on.
Empty the vacuum cleaner, discard the contents in the outside trash and use an anti-bacterial wipe to clean the vacuum. Let it dry thoroughly. If your manufacturer says your vacuum cannister is washable, wash it out with warm, soapy water and then rinse it and let it dry.
Dyson Hyperdymium™ motors work very differently to conventional brushed motors. We replaced the brush with digital pulse technology, added neodymium magnets and built a ceramic shaft that`s three times stronger than steel. This makes our motors durable and powerful, yet smaller, lighter and cleaner than ever before.
Dyson Hyperdymiumᵀᴹ motor

We reinvented motors to make them smaller, lighter and more power dense. Our Dyson Hyperdymium motors spin at 125,000 RPM – on average 5 times faster than a jet engine. A motor this powerful means that our vacuums have more powerful suction.

Most Dyson vacuums are designed for use with a standard household electrical outlet and have a voltage rating of around 110-120 volts. Some models are also available for use in countries with higher voltage standards, such as 220-240 volts.
If all you hear from the vacuum unit is a click at the when you try to start the vacuum motor from inside the house, then the motor in the unit is dead and has to be replaced. A strong odor from the shellac, which coats the copper coil windings, is an indicator that the motor is about to or has burnt out.
The most common problem with a vacuum cleaner is also the easiest to remedy: clogs in the hose or attachments. Also the electrical cord, motor, switch, fan, brushes, and motor bearings can all need repair or replacement.
We have two possible ways of adjusting the pressure in a vacuum system: first, by changing the pumping speed (altering the speed of the pump or throttling by closing a valve); second, through admission of gas (opening a valve).
All vacuum cleaners operate based on air flowing from the opening at the cleaning head or tool, through the vacuum cleaner and the bag and/or filter system and then out the exhaust port. This airflow is created by the vacuum motor, which also may be referred to as the suction motor.
The two main indicators to determine vacuum power performance are water lift and airflow. The water lift is measured in mmH2O, mbar or kPa. It represents the suction force and is the reference parameter for vacuuming liquids and heavy materials. The airflow is measured in m3/h or in l/s.
The most common problems found in vacuum cleaners are low suction force, excessive noise, burning smell, vacuum not turn on, and overheating. These issues can be fixed by either cleaning the device or replacing some parts of the device. At times, it is best to seek a professional to fix the cleaner effectively.
vacuum, space in which there is no matter or in which the pressure is so low that any particles in the space do not affect any processes being carried on there. It is a condition well below normal atmospheric pressure and is measured in units of pressure (the pascal).
220 air watts. Ideal for pet hair. Length of hose 4.4m.
A Dyson vacuum cleaner has two filters in it, a pre-motor and a post-motor filter.
The Dyson DC25 has a weight of only 7.3 kg which means carrying it up the stairs is no real problem. As it`s only a little over a metre tall makes it easier to store than other models when not in use.
Dyson DC25 ANIMAL Upright Vacuum Cleaner.
Product details

It`s recommended that you replace the HEPA Filter Cartridge Assembly on a yearly basis, as this filter can NOT be washed, and wash the secondary Pre-Motor filter once every 30 days, and replace it after 6 washing`s to maintain peak performance of your Dyson DC25.

Press and hold the power button on the machine and the remote together for 10 seconds. The LED screen will count down from 10. Once this count down has been completed, the machine will have been reset.
“Most vacuum cleaners will have two filters – pre-motor and post-motor. In general, the pre-motor filter would be made of foam or fabric and can handle a larger quantity of dust before needing cleaning. The post-motor filter would more likely be folded or pleated and made from a finer filter medium.
Regularly cleaning or replacing the filter will ensure that your vacuum is able to pick up all the dirt and debris it`s meant to. A dirty filter will decrease suction, meaning the vacuum picks less dirt and dust.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Bad Motor I have purchased two of the Kenmore direct drive beltless systems with Progressive systems. The first died after a year, the vacuum motor start making a grinding noies. I pulled the side HEPA filter and could see a fine coating of graphite like dust. Took it to a vacuum repair shop. They said the brushes were going and thus the motor was shot. I liked the vacuum and bought a second, 1 year later the motor is making a slight noise that and removing the HEPA filter I find a slight metall
ANSWER : That dust is from the carbon brushes on the motor. You may need to check them, and also clean out the motor compartment. A slight noise could be a motor bearing starting to go. Does the smell like rubber or electrical. If rubber, then the belt has stretched and needs to replaced. If electrical, then something is causing the motor to run hot, like a clogged filter, or it could be a motor going bad.

Read Full Q/A … : Vacuums

I purchased a Eureka C4910 last year and have a question that I am hoping you can answer.

There are two motor actions with this vacuum, 1) the vacuum suction, and 2) the beater bar. The action of the beater bar is that motor is supposed to automatically shut off when the handle is in the complete vertical position assuming the vacuum is stationary, but then turn on when the handle is tilted toward the floor, assuming the vacuum is moving back and forth.

The beater bar motor turn-on mechan

ANSWER : Good day!

Normally when the motor is easily moved back and forth means that it have a proper lubrication,proper alignment and no clogs.

When the motor and the belt is OK the problem could be on electrical wiring and switch.

If found electrical switch burned out you need to replaced it because when the switch is burn the contact of that switch is open even you turn it ON.that’s why the motor is not function because the voltage is not pass through the circuit because of open switch.You need to replaced it.
And check some fuses if any and other burned electrical wire.Replaced it also.

Thank you and don’t forget to rate my answer.

Read Full Q/A … : Vacuums

Dirt devil vacuum cleaner–trouble vacuuming dirt and pet hair on carpeting –is the problem with the spinning brush which contacts the floor,  not contacting the carpeting??  I thought (when I bought this vacuum) that the aforementioned brush was adjustable to various heights of carpeting.  Sometimes, it seems like nothing is being vacuumed up –unless I have just put a new bag on the vacuum… Do I need or can I replace the spinning brush on the bottom of the vacuum so it kicks up and vacuums
ANSWER : Try replacing the belt. Rubber belts stretch out after about a year.

Read Full Q/A … : Vacuums

I purchased a brand new Eureka Pet vacuum, sorry don’t know exact name but it the one that has the self cleaning duster on it. Last night I used the vacuum on my carpet, it was working fine until I accidently sucked up the corner of a scarf that was hanging off a couch. I shut the vacuum off, pulled out the scarf and and resumed vacuuming. Much to my dismay the suction on the vacuum had ceased. Can you tell me if there is a reset button on the vacuum? The vacuum does not appear to be damage
ANSWER : If the motor is running, there should be suction. Possible problems depend on whether it’s a canister or upright and are:
.A clog in the hose, UR or canister. Detach hose. Drop small coin in one end and lift hose causing it to roll out the other. If it does, no clog in hose. Drop same coin into hose opening on power head. If it rolls out, no clog in PN.
.Broken fan blades, UR. Needs to be taken to shop for repair/replacement.
.
.A reset button is for use if the motor isn’t running, so won’t have anything to do with the suction.

Read Full Q/A … : Vacuums

Motor Fried? Eureka 431BX Vacuuming, and then all of the sudden the motor just stopped. Well idk if it’s called the motor; the beater bar still spun, it was just the fan that stopped spinning Here is the whole vacuum in pieces http://i28.photobucket.com/albums/c237/SirFafner/Vacuum001.jpg Bottom Part, beater bar already taken out [Functions Fine] http://i28.photobucket.com/albums/c237/SirFafner/Vacuum002.jpg White Wire connecting to the fan motor [Looks black, i think it’s fried, and that’s the
ANSWER : Funny you said that,I went today and bought a bissel at Wal-Mart.Sure hope it lasts longer then the Eureka did.I will probably try to take the other one back to the store if I can find the receipt.Thanks so much.

Read Full Q/A … : Vacuums

I have a Kirby G4 Vacuum Cleaner – MOdel G4 D. I have never had any problems or repairs done to it in the past ten plus years that I’ve had it. This is an upright vacuum. I was vacuuming the carpet floor and was not having any trouble at all. I switched the vacuum off and moved it into a different room. When I tried to turn on the vacuum, it would not turn on. I checked with different outlets, used both front attachment and hose attachment. Checked the front part of the motor/ spiral case. This
ANSWER : Hello,
.My educated guess is that it’s either the switch or the power cord. Here are a couple of guides to help with diagnosis and repair…
.
.http://reviews.ebay.com/COMMON-PROBLEMS-WITH-THE-KIRBY-VACUUM-TROUBLESHOOTING_W0QQugidZ10000000003800312
.
.http://reviews.ebay.com/REPLACING-THE-POWER-SWITCH-ON-ANY-KIRBY-G-SERIES-VACUUM_W0QQugidZ10000000003752018
.
.Hope this helps!!
.Marci

Read Full Q/A … : Vacuums

Won’t start. My son was using the vacuum & Didn’t change the bag. The vacuum was making the full bag smell, but the light was’t on & it didn’t stop. I stopped him, changed the bag, checked the filter, closed the compartments & turned on the vacuum. Nothing happened. I checked to be sure that it was plugged in, that wasn’t the problem. I’ve let the vacuum “rest” for several days, It still won’t start. Any suggestions?
ANSWER : There is a reset button at the back of the powerhead. The user manual can be downloaded from the electrolux website, although I didn’t find it very useful. There was some info on how to change the powerhead drive belt.

Read Full Q/A … : Vacuums

Hello, I have a problem with my Eureka Powerline bagged upright vacuum. It has a 12 amp motor and is model #4352, Type D. It was probably bought new in 1998. My problem is, while vacuuming today the motor seemed to slow down all of the sudden and then began smelling like burning rubber. I shut the vacuum off to check for blockages but could not find anything blocked. When I then turned it on again it runs but seems to only be running at 1/2 the motor speed and still has the rubber buring smell.
ANSWER : It sounds like a rubber sealing in the motor has come loose and is being constantly rubbed against the walls of the motor with would cause the smell and loss of motor speed caused by the fricton of rubber against the rod so if you can get to the motor try to open it and see if you can get it if not take it to a small engine repair service hope this was helpful:)

Read Full Q/A … : Vacuums