Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

How to Identify and Fix Common Vacuum Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :

Your dirty water tank may not be secured tightly. Check the rubber tab on the dirty water tank and press firmly on all edges to secure it tightly. The accessory hose door also needs to be closed securely. Check the door and make sure it is locked in place.
Rinse your water tank with hot water, taking care to clean all around the pouch. Clean the top half of the tank through the nozzle area. Pop out the red filter and rinse that as well. Replace it before putting the tank back together.
You are leaving too much foam in the carpet

Dirt particles stick to it, and it is this that makes your water dirty when it is sucked up. If your carpet cleaning solution is too foamy, or you leave foam in the carpet, more dirt will be attracted to it.

So, you`ve decided to buy a Bissell Power Steam Pro Carpet Cleaner and are wondering what other cleaning solutions you can use in it. Well, you can use Baking soda, Vinegar, Castile soap, or even Warm Water. However, you must keep in mind that you should leave the carpets to dry after you use them.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

No Water My Bissell rug shampooer does not eject water or saop whan I pull the saop trigger on the handle. I checked both filters and they are clean. Then, I removed the container that sucks up the water and pulled the saop trigger, water barely came out of the tubes. I tried to clean the rug in our family room and the rug was not wet when I finished, no water coming out to clean the rug. HELP HELP HELP!!! I live in Colorado is there a Bissell repair shop near Denver, HELP!!! Thanks Dominick ema
ANSWER : Does water squirt out of the hose nozzle, if it does, then check the heater inside the handle asm. Make sure that where the tubes hook up to it are not clogged. If water doesn’t squirt, check for the seal at the bottom of the tank, it needs to be on the tank, not in the hole, this is for the soap bottle also, there is a seal on the bottom of it as well. The flow indictor cap is leaking air or maybe is too tight. If you had the top cover off, make sure that the tubes are routed right so as not to get pinched when the cover is put back on, the smart mix knob should be in the water setting and that the piston is on the bottom of the smart mix knob. Pump is bad. Try running a mix of vinegar and water to see if that unclogs the lines. Is the top cover and the base tight together in the back, sometimes the top breaks loose and it will raise up and it can’t spray, just re-fasten it down.
.
.Bissel’s Number is: 1-800-237-7691, they can tell you were to get service in your area.

I have a bissell quickwash 1950-e. I bought it Jan. 2006, and have only used it 8-10 times, I live in a very hard water area, so I though if I put some vinegar in with the cleaning solution it would get rid of any hard water deposits, unfortunatly the solution went lumpy in the tank and stoped spraying out water, I have opened it, hose clean, sprayer not blocked, x at bottom of water container when depresed water trickles out, component that opens the x when water container placed, also ran wate
ANSWER : Hard to say what is causing your problem, replacing the cap and insert on the water tank may help, part #2041111, even tho it may trickle out water when depressed, they can still be bad. The other thing would be the rod not relesing the water like it should. The big draw back to this model is Bissell has obsoleted all of its parts and most are no longer available. Might be wiser to buy new.

I have a Bissell Pro 2x carpet cleaner. The water heats properly as well as spraying the cleaning product. However, when I go to suction the water from the carpets, the 2 in 1 water tank bladder works properly but there is no dirty water outside the bladder. I have only used this carpet cleaner ~ 5 times and in the beginning I had to empty the suctioned water quite frequently as it was dirty and it could not not hold any more water. So I have done 1 room and all the dirt remains in the carpet
ANSWER : Check that the suction cone is not blocked. Check that the filter or hose to the bladder isn’t blocked as well.

Bissell 8920 proheat x2 brushes not turning i only noticed this after i finished cleaning.. or kinda cleaning because of the brushes ntot turning.. water comes out fine suction is fine but its not scrubbing so its not as clean as it could be. manual part works well water coming out hot. I did take it apart and cleaned off all the hairs in hopes maybe that was it.. put it together still nothing.. No idea how the belts should look onit and i cant find a picture or a video showing how belts look o
ANSWER : Hello,
.
.Here’s a link to a very helpful video that shows you step by step on how to access and replace the belt on your machine. When the brushes stop spinning, but the rest of the machine works fine, this is a tell-tale sign that your belt has gone bad.
.
.Video Showing how to access and change belt:
.http://www.bissell.com/VideoRating.aspx?id=1555
.
.If you open up your machine and find that the belt is still engaged, or you replace it and this doesn’t fix your problem, please feel free to use the comment form here on this repair page and I’ll be happy to walk you through some more advanced diagnosing.
.
.If you found this helpful, please be so kind and rate my repair helpful, or leave some feedback. This is really appreciated.
.
.Chris Jones
.GoVacuum.com

I have a Sunbeam Model Number 4065-000 and there is white particles comming out of the holes in the bottom. I think it is because we used tap water and there is a lot of deposits in the water. I read on the box that it was ok to use tap water and not distilled water. Is ther any way to clean the inside out to get the deposits cleaned out without affecting the possibility of doing something to the cloths that I will iron after cleaning the iron?
ANSWER : If the deposits are recent and still fairly soft, running a tank of vinegar through the machine should remove the deposits (obviously not using on any clothes, hold it over a sink). if the deposits are more stubborn, you can use a cleaning agent like CLR. rinse the tank out thoroughly after and run through a tank of clean water. good luck!

I have a Bissell Proheat 2XTurbo carpet cleaner. No water will come out when I squeeze the trigger. I have filled the solution tank and the water tank. I read the troubleshooting in the manual and have tried turning it off for a minute and restarting and nothing. I took out both tanks and reseated them and nothing. It has sat for over a year but did not have any water in the water tank. Some solution was left in the solution tank. How can I make the water come out? HELP!
ANSWER :

Call BISSELL Consumer Services.
.

1-800-237-7691
.

Mon-Fri: 8am to 10pm ET
.

Sat: 9am to 8pm ET

I have a bissell proheat 2x and it leaks water around the wheel it holds dirty water but doesnt hold clean water…….and how do i remove the wheel on my bissell
ANSWER : Hi,

Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.

Bissell Proheat Upright Wet/Dry Vacuum Problems

heatman101

Bissell proheat My Bissell won’t dispense cleaning formula but it sprays water and sucks up the water. The attachments spray water but not the soap also. how to fix?
ANSWER : First is the smart mix valve turning like it should? If it is then replace the soap dispensor. Also is the gasket on the valve at the bottom of the bottle?