Vacuums
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
All Kirby vacuums use the same size belt for the brush roller. This vac belt will fit every Kirby vacuum model roller brush, including: Avalir 2. Avalir.
If too much hair, string, or lint is caught in the brushroll, the brushroll can get stuck. If the brushroll is stuck, it will put too much strain on the belt and may cause the belt to break. Remove the brushroll and clean out any debris from the bearings. After replacing the brushroll, make sure that it turns freely.
Q: It smells like the belt is burning. What is wrong? A:It is likely the belt isn`t turning freely on the brush roll. Flip out the belt lifter handle and turn it clockwise until the green arrows line up.
Q: It smells like the belt is burning. What is wrong? A:It is likely the belt isn`t turning freely on the brush roll. Flip out the belt lifter handle and turn it clockwise until the green arrows line up.
If your LED flickers a lot like on the third animation you MUST change your belt immediately. If you can barely see the green LED or is permanently off change your belt immediately and book your machine for service.
If your vacuum runs but isn`t always picking up dirt, it might be time to change the belt. Consumer Reports` experts reveal how fast and simple it is to install a new belt which can save you a trip to the repair shop.
Next to the motor, the belt on your vacuum is just about the most important part of your vacuum. Without the belt to spin the brushroll, most vacuums won`t pick up on carpeting at all! If your vacuum uses a rubber belt, check it once a month for cracks, melting, and especially, slippage.
The Dyson vs. Kirby vacuum cleaners debate can be complicated, as these brands are so different. If it comes down to price or size, Dyson will probably get the upper hand — but for all other vacuuming considerations, Kirby is the way to go.
Kirby vacuum prices are higher than many vacuums found at big-box stores, but that`s because Kirby vacuums are made of durable materials that will last for years. Why replace an inexpensive vacuum over and over again when you can purchase a Kirby vacuum? This complete home cleaning system that will last for a lifetime.
If too much hair, string, or lint is caught in the brushroll, the brushroll can get stuck. If the brushroll is stuck, it will put too much strain on the belt and may cause the belt to break. Remove the brushroll and clean out any debris from the bearings. After replacing the brushroll, make sure that it turns freely.
Since you`ll likely only replace your serpentine belt once during the life of your car, it`s generally recommended to take your car to a professional mechanic. You can do a lot of damage to your vehicle if you drive on the road with an improperly installed serpentine belt.
Vacuum belts connect to the brush roller and assist in collecting debris. On the other side of the belt is usually the drive shaft or motor pulley. After regular usage, the belt will stretch out, lessening the tension on the brush roller. Lesser tension diminishes the brush roller`s turn rate and speed.
(All full-sized machines, upright vacuums and canister vacuums, typically have a belt.) A vacuum will still create suction with a bum belt, but without a rotating brush roller, it won`t collect much in the way of dirt and debris, especially on carpets.
HQRP Vacuum Belt is designed to replace Kirby 301291 Belt or older part numbers 301282, 301289, 159056. Available in a convenient two-count package. Fits all Kirby Vacuum models that use a flat belt.
Return Policy for Purchases through Kirby.com
Thank you for shopping Kirby! Any new Kirby product, excluding chemicals and cleaning formulas, purchased through our website may be returned within thirty (30) days from date of delivery.
Kirby Vacuum Systems: Heavy-Duty Cleaning for Years to Come
If you demand the absolute best in your vacuum cleaner, you can`t go wrong with the Kirby Avalir 2. This trusted solution is built to last, so it will deliver years of deep cleaning.
Manufacturing Date: 2003 – 2006
The Diamond Edition model was a popular model with our customers because of its classic design and improvements from the Ultimate G Series. This model included Kirby`s Allergen Reduction Filters, which provide greater filtration than paper bag filters.
Amazon. Dusting brushes usually have angled bristles designed to sweep and force dust into the hose. These are great tools for vacuuming hard surfaces, delicate areas, and upholstery.
All Kirby vacuums use the same size belt for the brush roller. This vac belt will fit every Kirby vacuum model roller brush, including: Avalir 2. Avalir.
Serpentine belt replacement is easy because today`s automatic drive belt tensioners eliminate the need to loosen bolts or pry components into position for retensioning. Just rotate the tensioner, remove the old belt and install a new one.
In most cases, a timing belt kit will run between $100 -350. Labor on most timing belts is between 3-5 hours, putting your total cost between $400 -1,000.
Some manufacturers like GM or Mazda do not recommend giving a second chance to the belt once it has been taken off. On the other hand, Chrysler and Ford say the belt can be reused if there are no problems found with the belt.
Put on a pair of pants that fits well and stand in a relaxed position. Then wrap a soft tape measure through the belt loops so the tape is snug but not too tight. This measurement is your belt size. You may need to round up to the nearest even-numbered inch.
The most accurate way to determine your belt size is to thread a flexible tape measure through the belt loops of your pants (as you would with a belt) and mark the spot where the tape reaches exactly one time around your hip. Pick the belt size which is closest to your hip circumference.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
Windtunnel belt I have a new Hoover Windtunnel canister. The belt keeps coming off. It happened a couple weeks ago (several times after putting the belt back on) so I assumed I might need a new belt as it might have dried out at the store. I ordered new belts and today I used it for about an hour and the belt came off again, twice. There doesn’t seem to be anything to hold the belt on the stem as it seems to slip off. I have tried it centered, to the left and to the right….can you help. I am v
ANSWER : I’ve successfully used a compatible belt – Royal 104425001 .It’s still new, but for the time being at least – it works.
Read Full Q/A … : Vacuums
How to put a belt on silver addition kirby vaccum cleaner
ANSWER : The following site has videos for changing belt on the Kirby vacuums. It should apply to your. Much simpler and better than just a written reply.
.
.http://www.kirby.com/portals/0/videos.html
.
.http://www.kirby.com/portals/0/videos.html
Read Full Q/A … : Vacuums
We have had three belts break on your hoover vaccum cleaner u5472-940. It is easy to replace, you just remove the plastic part over it, put belt on wheel and then put it back on. Any idea on why the belt keeps breaking?
ANSWER : Sometimes when you buy belts from the walmart or target, they are not at the correct specification and they brake as soon as you turn on the machine. i would suggest that you buy these belts from the company.
Read Full Q/A … : Vacuums
I’m using (or WAS using) a Eureka ”the boss” model 8803. The belt broke, no biggie, so I replaced it with a Eureka model U belt, the problem is when I put the new belt on and turn on the vaccuum, the belt breaks again. I am also having trouble getting the brush roller to fit right when the belt is in place. I can’t find any sharp edges that would cut the belt,nor can I find where any small bits may have broken. Anyone have a solution for me?
ANSWER : First, make sure you have the right belt, second, i am thinking that you are not lineing the roller up right, it will only fit one way. look at the ends of the roller and the grooves where it slides in, you should be able to see clearly how it goes.
Read Full Q/A … : Vacuums
Hoover WindTunnel Self-Propelled V Belt
ANSWER : I had this same problem with the V belt on my Hoover Vaccuum..
.There are three (3) basic things that will cause the brush roll not to spin..
.1. When handle is upright, brush roll is OFF..2. When switch is set for HARD surface, brush roll is OFF..3. Broken/worn FLAT belt or V Belt, brush roll will not spin.
.
.I noticed that the brush roll was not spinning when my vacuum was set for CARPET. After removing the cover I noticed that the V belt was loose, I thought the belt was worn so I purchased a correct replacement belt and installed it, but the new belt was also loose and when I turned the large flat belt pulley it did not turn the V belt pulley at the same time..
.I double checked the surface setting and I had the vacuum switch set for carpet, but still when I released the handle out of the upright position the brush roll would still not spin..
.My aggravation finally led me to this posting on FixYa’s website..
.The first thing I did was checked the screw to the left of the V belt as suggested by ejmjr5 and this did nothing to solve the problem or create more tension on the V belt, even when the upright handle was not in the upright position..
.After playing around with the surface setting control switch/nob I notice that when I moved the switch out of the HARD surface setting and over to CARPET, I had thought that the switch was set for CARPET as it visually appeared, but I was not pushing the switch over hard enough to click it into the CARPET setting mode..
.VOILA, the brush roll now spins correctly even though the V belt seams to be too loose for the pulley..
.You really have to force the switch into the CARPET setting. Be sure that you hear the switch/nob click into place..
.Now you can effectively clean up after that hangover of a party!.
.Burp!
.There are three (3) basic things that will cause the brush roll not to spin..
.1. When handle is upright, brush roll is OFF..2. When switch is set for HARD surface, brush roll is OFF..3. Broken/worn FLAT belt or V Belt, brush roll will not spin.
.
.I noticed that the brush roll was not spinning when my vacuum was set for CARPET. After removing the cover I noticed that the V belt was loose, I thought the belt was worn so I purchased a correct replacement belt and installed it, but the new belt was also loose and when I turned the large flat belt pulley it did not turn the V belt pulley at the same time..
.I double checked the surface setting and I had the vacuum switch set for carpet, but still when I released the handle out of the upright position the brush roll would still not spin..
.My aggravation finally led me to this posting on FixYa’s website..
.The first thing I did was checked the screw to the left of the V belt as suggested by ejmjr5 and this did nothing to solve the problem or create more tension on the V belt, even when the upright handle was not in the upright position..
.After playing around with the surface setting control switch/nob I notice that when I moved the switch out of the HARD surface setting and over to CARPET, I had thought that the switch was set for CARPET as it visually appeared, but I was not pushing the switch over hard enough to click it into the CARPET setting mode..
.VOILA, the brush roll now spins correctly even though the V belt seams to be too loose for the pulley..
.You really have to force the switch into the CARPET setting. Be sure that you hear the switch/nob click into place..
.Now you can effectively clean up after that hangover of a party!.
.Burp!
Read Full Q/A … : Vacuums
I need to put a new belt on the vaccum cleaner,om
ANSWER : You can get any bissell belt you need at www.vacbelts.com
Read Full Q/A … : Vacuums
Hi my proheat bissell 7901 stopped pumping water to the floor, but it pumps water from the hand hose. I read the manual and followed how to check belt and the flat belt on right side of shampooer is fine and I turned on and it turns and so do the brushes at the bottom of the machine. I was reading online and I guess there’s two belts on this machine? where can I find the other belt to see if it needs replacing. I guess it’s a ribbed belt? that is the water pump belt?
ANSWER : Just taken ours apart with the same problem… found it was caused by the 2 halves of the main casing coming apart in the area where the upright pedal release is. I found this to be due to the upper casing having broken in 2 places – the bottom of the screw wells..This means that the water tank cannot exert sufficient pressure on the valve to release the water..Only solution is a new top cover assembly
Read Full Q/A … : Vacuums
The belt on my Kirby G3 wore out, and I bought replacement belts from two different sources–one an official Kirby supplier and one a store brand. Neither belt is long enough to catch the belt lifter when it is rotated and to reach the drive shaft.
ANSWER : Kirby has only had 1 belt from day one. sometimes you do need to push the belt up to catch the belt lifter
Read Full Q/A … : Vacuums
