dyson dc40removed lower hose to check for blockage and cannot reattach.

How to Identify and Fix Common Vacuum Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :

Push the wand into the end of the hose until it clicks into position. Slide the wand down into the hose. Close the wand end cap. Remove the tool and slide the wand back into the hose.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Hose Problem The hose broke just above the cuff on the inlet end of the hose.  I found that the hose doesn’t thread into this cuff but appears to be heat bonded in some way. Can I get a replacement cuff or do I have to replace the hose?
ANSWER : Looks like you can just get the hose, part #38479-4, It should just screw into the adapter or it may be glued in.

Read Full Q/A … : dyson dc40

Torn Hose The hose on my Dyson is torn right at the top where the the accessories connect. I was able to take the connection apart and shorten the hose, but I don’t know what to use to reattach the hose to the black fitting. It looks like it was glued…not sure what kind. Any ideas?
ANSWER : Duct tape

Read Full Q/A … : dyson dc40

My bissell proheat upright steam cleaner is spraying out through the attachments just fine, but will not spray to the floor when using upright. we’ve taken it apart to find that there is no water at all going through one of the hoses, but it appears the hose is connected behind the on/off and heat switches, we can’t seem to figure out how to get in there to replace that hose….any suggestions on how to access this?? just curious how you would get in to replace the hose, we know it is the hose..
ANSWER : Hi,

Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.

Bissell Proheat Upright Wet/Dry Vacuum Problems

heatman101 .
.xbnxb

Read Full Q/A … : dyson dc40

Hoover agility steamer lower hose broken
ANSWER : Go in your garage or to your workbench and grab a BFH whack the **** out of the rest of the steamvac and never buy one again. For those of you not familiar with a BFH it is a Big F_ _ _ ing Hammer.

Read Full Q/A … : dyson dc40

Wand won’t go into the flexible hose
ANSWER : Try some fine sandpaper or one could heat up
the wand or hose with a heatgun or torch
to flex it and then try plugging it in.

Read Full Q/A … : dyson dc40

There is a cut at the end of the hose. Is there a way to cut the hose at the split and reattach it to the connection? Thanks.
ANSWER : Unfortunatly the amswer is no you will have to replace the whole part.

Read Full Q/A … : dyson dc40

Hose disconnected There is a clear circle on the part where the hose connects to the cannister (above the orange ball) that is in a position that has the hose disconnected. I can move the circle so that the hose connects, but it won't lock in that position. Help!
ANSWER : This video may help

Read Full Q/A … : dyson dc40

I HAVE A BISSELL PROHEAT CARPET CLEANER 7920 I DISSEMBLY IT TO CLEAN IT. I DON’T KNOW IF I PUT THE HOSES BACK IN THE RIGHT LOCATION BECAUSE AFTER I PUT IT BACK TOGETHER IT’S LEAKING WATER ALL OVER THE FLOOR BUT IT WILL RECOVER THE WATER FROM THE FLOOR AND THE SOLUTION WON’T SPARY OUT I THINK THE HOSES ARE NOT IN THEIR RIGHT LOCATION TO STOP THE FLOW WHEN IT’S NOT SUPPOSE TO BE COMING OUT CONSTANTLY HELP PLEASE IS THEIR A HOSE DIAGRAM FOR THE HOSES INSIDE THE CARPET CLEANER
ANSWER : Hi,

Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.

Bissell Proheat Upright Wet/Dry Vacuum Problems

heatman101 .
.dfjddj

Read Full Q/A … : dyson dc40