send a diagram? Thanks
Oreck XL M900A Upright WetDry Vacuum
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
Should the brush not rotate freely there may be debris tangled around the ends of the brush, carefully remove any obstructions or replace the brush with a new one. We recommend that you fit a new belt and brush once per year to keep your Reactive vacuum working efficiently.
Hold the floor tool as best as you can using your foot and twist the metal pipe.. this should `break the bond`. As soon as you have movement after twisting the pipe, you should find that it pulls free.
“Wash” allows the water to mix with the cleaning solution; “Rinse” stops the mixing and allows only water to be sprayed.
To release the wand on the Hoover® REACT™ Powered Reach™ Plus press the Powered Reach™ Mode button on the top of the canister. This will allow you to remove the canister and access the wand release. The wand release button is located on the spine of the vacuum directly behind the dirt cup.
To release the wand on the Hoover® REACT™ Powered Reach™ Plus press the Powered Reach™ Mode button on the top of the canister. This will allow you to remove the canister and access the wand release. The wand release button is located on the spine of the vacuum directly behind the dirt cup.
A: To remove the handle there is a release button inside where the cleaner holds the water tank. The button is on the side where the handle is. Helpful? Thank you for your feedback!
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
My bissell proheat upright steam cleaner is spraying out through the attachments just fine, but will not spray to the floor when using upright. we’ve taken it apart to find that there is no water at all going through one of the hoses, but it appears the hose is connected behind the on/off and heat switches, we can’t seem to figure out how to get in there to replace that hose….any suggestions on how to access this?? just curious how you would get in to replace the hose, we know it is the hose..
ANSWER : Hi,
Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.
Bissell Proheat Upright Wet/Dry Vacuum Problems
heatman101 .
.xbnxb
Read Full Q/A … : Oreck XL M900A Upright WetDry Vacuum
Hose Problem The hose broke just above the cuff on the inlet end of the hose. I found that the hose doesn’t thread into this cuff but appears to be heat bonded in some way. Can I get a replacement cuff or do I have to replace the hose?
ANSWER : Looks like you can just get the hose, part #38479-4, It should just screw into the adapter or it may be glued in.
Read Full Q/A … : Oreck XL M900A Upright WetDry Vacuum
Hello, I have a Hoover quadraflex Powermatic central vacuum system Model # s8099-031 that requires a new replacement 35 ft hose…I have contacted Hoover and they do not know where to buy a replacement hose for this model. I live in Canada. Any idea where I can get a replacement hose for this system? Thanks kindly, Tammy
ANSWER : Tammy, no info re your location, so I”l try this.
Your Hoover hose is shot because it was made of rubber.There are new swivel handled, tangle proof lighter hoses made of vinyl which will last much longer and can be adapted to the old Hoover head by changing the upper steel tube.
Find a Hoover service center, outlet in the yellow pages and ask for the “NEW “style, gray“Plastiflex“ brand hose and upper adapter tube sold with new Hoovers at Costco and you will be all set. Then, when the head eventually dies, you can upgrade to a far better one , while still having the Hoover cannister, the hose and tools do not need to match the original tank.
Your Hoover hose is shot because it was made of rubber.There are new swivel handled, tangle proof lighter hoses made of vinyl which will last much longer and can be adapted to the old Hoover head by changing the upper steel tube.
Find a Hoover service center, outlet in the yellow pages and ask for the “NEW “style, gray“Plastiflex“ brand hose and upper adapter tube sold with new Hoovers at Costco and you will be all set. Then, when the head eventually dies, you can upgrade to a far better one , while still having the Hoover cannister, the hose and tools do not need to match the original tank.
Read Full Q/A … : Oreck XL M900A Upright WetDry Vacuum
Hose disconnected There is a clear circle on the part where the hose connects to the cannister (above the orange ball) that is in a position that has the hose disconnected. I can move the circle so that the hose connects, but it won't lock in that position. Help!
ANSWER : This video may help
Read Full Q/A … : Oreck XL M900A Upright WetDry Vacuum
Torn Hose The hose on my Dyson is torn right at the top where the the accessories connect. I was able to take the connection apart and shorten the hose, but I don’t know what to use to reattach the hose to the black fitting. It looks like it was glued…not sure what kind. Any ideas?
ANSWER : Duct tape
Read Full Q/A … : Oreck XL M900A Upright WetDry Vacuum
Replaced internal pump. Color coded hoses for replacement. Marker has worn off hoses. Need proper routing of hoses from clean water tank, to heater to spray nozzles. An internal schematic of hose routing is preferred.
ANSWER : Hi
.
.Thanks for using FixYa. Please remove the top cover of your Bissell cleaner. Now place the Auto-Mix selector knob to the water only position. Turn the cover over. You will notice an angle on the top of the piston. This will fit between a couple of plastic ridges on the top cover by the selector screw.
.Now angle the piston slightly forward and engage the angled cut in the top of the piston with the screw thread and pull back. Turn the screw to the high traffic position and replace the cover. Apply a very little amount of silicon grease around the Auto-Mix piston ‘O’ ring, it will ease the re- installation of the cover.
.
.You can also see this manual for more detailed instructions–
.
.Bissell 7901 steam cleaner Manual
.
.Please do accept the solution if the issue is resolved or else revert for further assistance.
.
Thanks
Rylee
.
.Thanks for using FixYa. Please remove the top cover of your Bissell cleaner. Now place the Auto-Mix selector knob to the water only position. Turn the cover over. You will notice an angle on the top of the piston. This will fit between a couple of plastic ridges on the top cover by the selector screw.
.Now angle the piston slightly forward and engage the angled cut in the top of the piston with the screw thread and pull back. Turn the screw to the high traffic position and replace the cover. Apply a very little amount of silicon grease around the Auto-Mix piston ‘O’ ring, it will ease the re- installation of the cover.
.
.You can also see this manual for more detailed instructions–
.
.Bissell 7901 steam cleaner Manual
.
.Please do accept the solution if the issue is resolved or else revert for further assistance.
.
Thanks
Rylee
Read Full Q/A … : Oreck XL M900A Upright WetDry Vacuum
Rainbow shampooer The soap dispenser on my Rainbow is not dispensing soap when I flip the switch to ‘soap’ mode. All connections are intact. All plastic hoses are intact. What do you think is going on? The soap bottle connects to a little straw that appears to be free of obstruction, however, it connects into a sealed casing on the hose.
ANSWER : The little “wash/rinse” switch on some of the Aquamate units shuts off the soap flow by kinking the tube inside the housing. If you leave the switch in the rinse position (therefore, kinked) when you’re done using it, it may dry in the kinked position. Taking apart the top part of the handle where all this mechanism is and cleaning out the tube by soaking it in some warm water for a while and reshaping the kinked part before you reassemble it may help solve this problem.
Read Full Q/A … : Oreck XL M900A Upright WetDry Vacuum
Rainbow D4C power switch replacement
ANSWER : As far as I know, that switch with 6 terminals is still available. But if not, I would wire the 2 for the power head and the 2 motor wires together. Then you would have 4 leads to attach.
Read Full Q/A … : Oreck XL M900A Upright WetDry Vacuum
