Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

How to Identify and Fix Common Vacuum Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :

Yes, it is safe to leave cleaning formula in the clean tank when not in use.
Yes, you should keep cleaning the carpet until the water is clear. This will ensure that your carpets are clean and free of dirt, dust, and other allergens. However, you should be careful not to scrub too hard or use too much water. Doing so can damage the carpet and lead to more stains in the future.
Remove the hose from the base of the machine and remove any debris as needed. If necessary, you may use a broom handle to unclog the hose by pushing through both openings. If the clog persists, please refer to our Brush Roll Maintenance video.
Check to see if your clean water tank is empty. The clean water tank also may not be seated properly. The brush window could also not be latched into place. Turn off your machine and check to see if the brush window is secure.
Plugged vacuum hoses are sometimes the reason for a loss in suction. Hoses can get clogged with hair, dust bunnies, string, or anything else that can`t pass through the other end of the hose. Airways inside the machine should be looked at as well. Wherever there is an air passage, check it.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

I cannot remember where all the tubes that carry the water go after taking it apart
ANSWER : Please to to the web pages videos for troubleshooting and help: God bless you.
http://www.bissell.com/how-to-videos/

I have a Bissell Pro 2x carpet cleaner. The water heats properly as well as spraying the cleaning product. However, when I go to suction the water from the carpets, the 2 in 1 water tank bladder works properly but there is no dirty water outside the bladder. I have only used this carpet cleaner ~ 5 times and in the beginning I had to empty the suctioned water quite frequently as it was dirty and it could not not hold any more water. So I have done 1 room and all the dirt remains in the carpet
ANSWER : Check that the suction cone is not blocked. Check that the filter or hose to the bladder isn’t blocked as well.

I have a bissell quickwash 1950-e. I bought it Jan. 2006, and have only used it 8-10 times, I live in a very hard water area, so I though if I put some vinegar in with the cleaning solution it would get rid of any hard water deposits, unfortunatly the solution went lumpy in the tank and stoped spraying out water, I have opened it, hose clean, sprayer not blocked, x at bottom of water container when depresed water trickles out, component that opens the x when water container placed, also ran wate
ANSWER : Hard to say what is causing your problem, replacing the cap and insert on the water tank may help, part #2041111, even tho it may trickle out water when depressed, they can still be bad. The other thing would be the rod not relesing the water like it should. The big draw back to this model is Bissell has obsoleted all of its parts and most are no longer available. Might be wiser to buy new.

No Water My Bissell rug shampooer does not eject water or saop whan I pull the saop trigger on the handle. I checked both filters and they are clean. Then, I removed the container that sucks up the water and pulled the saop trigger, water barely came out of the tubes. I tried to clean the rug in our family room and the rug was not wet when I finished, no water coming out to clean the rug. HELP HELP HELP!!! I live in Colorado is there a Bissell repair shop near Denver, HELP!!! Thanks Dominick ema
ANSWER : Does water squirt out of the hose nozzle, if it does, then check the heater inside the handle asm. Make sure that where the tubes hook up to it are not clogged. If water doesn’t squirt, check for the seal at the bottom of the tank, it needs to be on the tank, not in the hole, this is for the soap bottle also, there is a seal on the bottom of it as well. The flow indictor cap is leaking air or maybe is too tight. If you had the top cover off, make sure that the tubes are routed right so as not to get pinched when the cover is put back on, the smart mix knob should be in the water setting and that the piston is on the bottom of the smart mix knob. Pump is bad. Try running a mix of vinegar and water to see if that unclogs the lines. Is the top cover and the base tight together in the back, sometimes the top breaks loose and it will raise up and it can’t spray, just re-fasten it down.
.
.Bissel’s Number is: 1-800-237-7691, they can tell you were to get service in your area.

I have the Bissell 2x proheat. There is no water being sucked up from the bladder and the cleaning solution is not being sucked in either in order to get to the carpet. On water rinse the carpet gets wet but I’m not seeing any water going through the clear front piece. I live in Harvest Alabama. Where can I take it to get fixed if it needs it?
ANSWER : Hi,

Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.

Bissell Proheat Upright Wet/Dry Vacuum Problems

heatman101 .
.retqwe

I have a Bissell Proheat 2XTurbo carpet cleaner. No water will come out when I squeeze the trigger. I have filled the solution tank and the water tank. I read the troubleshooting in the manual and have tried turning it off for a minute and restarting and nothing. I took out both tanks and reseated them and nothing. It has sat for over a year but did not have any water in the water tank. Some solution was left in the solution tank. How can I make the water come out? HELP!
ANSWER :

Call BISSELL Consumer Services.
.

1-800-237-7691
.

Mon-Fri: 8am to 10pm ET
.

Sat: 9am to 8pm ET

Bissell will spray water when set to water rinse, but as soon as it is set to light, normal, or heavy cleaning, there is no spray. I have tried priming but to no avail. I put plain water in the solution tank to test without ay success. It is like it loses it’s prime whenever you try to use a solution mix. Once you set it back to water rinse only and go through the priming steps, it is OK. Any help would be appreciated. Thanks.
ANSWER :

Please check the following with liquid in both tanks.
.

.

– Check to see if the machine will spray through the hose with the setting on tools. If it does, the pump is fine. Continue troubleshooting.
.

Check for debris on spray tips. Clean them with a soft brush (on old tooth brush works well). The spray tips may be lifted out for easier access.
.

– Ensure the tank lid is properly attached to the bottom of the tank. To attach this properly, remove the Water Tank from the machine. Hook the front window onto the lip of the bottom container and then allow the window with lid to cover the complete tank. Secure the latch on the back of the bottom tank to the back of the tank lid. THE TANK LID CANNOT BE ATTACHED PROPERLY IF THE BOTTOM TANK IS ALREADY INSTALLED IN THE MACHINE.
– Check the bottom of the Water Tank and the Formula Tank to make sure each has a red auto-load gasket attached. Make sure the Water Tank and the Formula Tank are seated properly. Depress the x on this gasket to ensure this depresses and release back out. Liquid from the tank should dispense.
.

– Remove the handle completely and re-attach. Once the handle is re-attached, re-attempt to spray.
.

.

If the machine continues to not spray, check the following:
.

REMOVE THE COLLECTION TANK:
• Make sure the unit is set to water rinse
• Remove the smart mix bottle and fill it with water only
• Place the smart mix bottle into the collection tank reservoir
• Run the unit and try to spray. If the machine sprays, you will be able to see the water level decreasing in the smart mix bottle and you will need to replace the bottom tank. It is possibly warped.
.

If these suggestions do not resolve your issue, contact BISSELL Consumer Services.
.

1-800-237-7691
Mon-Fri: 8am to 10pm ET
Sat: 9am to 8pm ET

Hoover aquamaster recently purchased hoover aquamaster, trying to shampoo carpet, can’t get water to come down tubes, water keeps going into dirty water tank.help!!!!!!!!!!!!!!!
ANSWER : Sounds like you need to attach the air hose
.
.with reservoir in place you clip on the lid with tubes attached, one of them goes down to the floor cleaning nozzle, the other tube should be about 20cm long with an end piece,
.
.this is the air hose and it fits into a small hole under the reservoir on the motor housing (the heavy mains powered part that clips onto the big recovery drum that sits on floor)
.
.it’s mentioned briefly in the manual, here it is in pdf form http://www.box.net/shared/rnh39ffjcq