Bissell 8975 CleanView Bagless Upright Vacuum
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
Your CleanView/PowerClean Swivel vacuum has a Brush Roll and Belt that may require some maintenance.
If brush will not turn by hand, or belt is broken, replace the damaged part by ordering online at BISSELL.com. Clean off any debris on the brush. If the brush is still not turning, please take the unit to an Authorized Service Center to have a Quality Technician inspect the unit.
If brush will not turn by hand, or belt is broken, replace the damaged part by ordering online at BISSELL.com. Clean off any debris on the brush. If the brush is still not turning, please take the unit to an Authorized Service Center to have a Quality Technician inspect the unit.
BISSELL® CleanView® is a powerful lightweight upright vacuum cleaner that packs a multi-surface cleaning punch and lets you maneuver easily from room to room. Our OnePass™ and Scatter-Free Technology allows you to clean carpets simply on the first pass*, and clean debris from hard surfaces with less scatter.
If brush will not turn by hand, or belt is broken, replace the damaged part by ordering online at BISSELL.com. Clean off any debris on the brush. If the brush is still not turning, please take the unit to an Authorized Service Center to have a Quality Technician inspect the unit.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
Replaces the belt on dirt devil dynamite pluse model put everything back together started it and it burt the new belt up that fast. I put it around the beater brush and the metal bar I thought it should go around, yet it seemed like there should be something else there to put the belt on. What do you suggest? Do you have picture I could go by?
ANSWER : The metal bar you put it around if the bar itself does not spin it is going to burn the belt up. Every thing that the belt is supposed to go around has to turn or the belt will rub on the piece not moving and brake.
Read Full Q/A … : Bissell 8975 CleanView Bagless Upright Vacuum
I’m using (or WAS using) a Eureka ”the boss” model 8803. The belt broke, no biggie, so I replaced it with a Eureka model U belt, the problem is when I put the new belt on and turn on the vaccuum, the belt breaks again. I am also having trouble getting the brush roller to fit right when the belt is in place. I can’t find any sharp edges that would cut the belt,nor can I find where any small bits may have broken. Anyone have a solution for me?
ANSWER : First, make sure you have the right belt, second, i am thinking that you are not lineing the roller up right, it will only fit one way. look at the ends of the roller and the grooves where it slides in, you should be able to see clearly how it goes.
Read Full Q/A … : Bissell 8975 CleanView Bagless Upright Vacuum
The belt on my vacuum cleaner model 6596 bissel powerforce bagless turbo keeps breaking. As soon as I put on a new belt and start it up the belt snaps. It is the durabelt meant for this vacuum model. Also, my son has been having the same problem with his. He has the same model and same belt. This problem is occurring even after a thourough cleaning.
ANSWER : I would guess you aren’t centering the belt correctly, thus it’s edge is caught between the brush and another solid object, causing the breakage.
.When you get the belt on the the brush and the brush back in place, turn the brush a few times by hand to make sure it’s not catching on anything. After you get the powerhead put back together, do this again. It’s a common problem if the powerhead isn’t assembled correctly.
.
.Here’s a video clip from the Bissell site demonstrating changing the belt.
.
.http://www.bissell.com/how-to-videos/replace-brush-belt-vacuums/
.When you get the belt on the the brush and the brush back in place, turn the brush a few times by hand to make sure it’s not catching on anything. After you get the powerhead put back together, do this again. It’s a common problem if the powerhead isn’t assembled correctly.
.
.Here’s a video clip from the Bissell site demonstrating changing the belt.
.
.http://www.bissell.com/how-to-videos/replace-brush-belt-vacuums/
Read Full Q/A … : Bissell 8975 CleanView Bagless Upright Vacuum
I am trying to replace my vacuum belt and can not get the roller brush to fit back into the slot after I put the belt back onto one end of the roller brush. Am I reassembling the belt and roller brush the right way?
ANSWER : If its a hoover or bissell, one side of the brushroll is slotted and slides. if its a eureka the hexagon end caps must be properly aligned, they go in at an angle. if its none of these provide me with the make and model # and i will give you a detailed description on installation. let me know if you need more help.
Read Full Q/A … : Bissell 8975 CleanView Bagless Upright Vacuum
Windtunnel belt I have a new Hoover Windtunnel canister. The belt keeps coming off. It happened a couple weeks ago (several times after putting the belt back on) so I assumed I might need a new belt as it might have dried out at the store. I ordered new belts and today I used it for about an hour and the belt came off again, twice. There doesn’t seem to be anything to hold the belt on the stem as it seems to slip off. I have tried it centered, to the left and to the right….can you help. I am v
ANSWER : I’ve successfully used a compatible belt – Royal 104425001 .It’s still new, but for the time being at least – it works.
Read Full Q/A … : Bissell 8975 CleanView Bagless Upright Vacuum
Hoover WindTunnel Self-Propelled V Belt
ANSWER : I had this same problem with the V belt on my Hoover Vaccuum..
.There are three (3) basic things that will cause the brush roll not to spin..
.1. When handle is upright, brush roll is OFF..2. When switch is set for HARD surface, brush roll is OFF..3. Broken/worn FLAT belt or V Belt, brush roll will not spin.
.
.I noticed that the brush roll was not spinning when my vacuum was set for CARPET. After removing the cover I noticed that the V belt was loose, I thought the belt was worn so I purchased a correct replacement belt and installed it, but the new belt was also loose and when I turned the large flat belt pulley it did not turn the V belt pulley at the same time..
.I double checked the surface setting and I had the vacuum switch set for carpet, but still when I released the handle out of the upright position the brush roll would still not spin..
.My aggravation finally led me to this posting on FixYa’s website..
.The first thing I did was checked the screw to the left of the V belt as suggested by ejmjr5 and this did nothing to solve the problem or create more tension on the V belt, even when the upright handle was not in the upright position..
.After playing around with the surface setting control switch/nob I notice that when I moved the switch out of the HARD surface setting and over to CARPET, I had thought that the switch was set for CARPET as it visually appeared, but I was not pushing the switch over hard enough to click it into the CARPET setting mode..
.VOILA, the brush roll now spins correctly even though the V belt seams to be too loose for the pulley..
.You really have to force the switch into the CARPET setting. Be sure that you hear the switch/nob click into place..
.Now you can effectively clean up after that hangover of a party!.
.Burp!
.There are three (3) basic things that will cause the brush roll not to spin..
.1. When handle is upright, brush roll is OFF..2. When switch is set for HARD surface, brush roll is OFF..3. Broken/worn FLAT belt or V Belt, brush roll will not spin.
.
.I noticed that the brush roll was not spinning when my vacuum was set for CARPET. After removing the cover I noticed that the V belt was loose, I thought the belt was worn so I purchased a correct replacement belt and installed it, but the new belt was also loose and when I turned the large flat belt pulley it did not turn the V belt pulley at the same time..
.I double checked the surface setting and I had the vacuum switch set for carpet, but still when I released the handle out of the upright position the brush roll would still not spin..
.My aggravation finally led me to this posting on FixYa’s website..
.The first thing I did was checked the screw to the left of the V belt as suggested by ejmjr5 and this did nothing to solve the problem or create more tension on the V belt, even when the upright handle was not in the upright position..
.After playing around with the surface setting control switch/nob I notice that when I moved the switch out of the HARD surface setting and over to CARPET, I had thought that the switch was set for CARPET as it visually appeared, but I was not pushing the switch over hard enough to click it into the CARPET setting mode..
.VOILA, the brush roll now spins correctly even though the V belt seams to be too loose for the pulley..
.You really have to force the switch into the CARPET setting. Be sure that you hear the switch/nob click into place..
.Now you can effectively clean up after that hangover of a party!.
.Burp!
Read Full Q/A … : Bissell 8975 CleanView Bagless Upright Vacuum
We have a Hoover upright vacuum cleaner, model Core 7. There is a switch that turns on and off the brush drive. This operates via a cam with a bearing putting pressure on the final drive belt to engage the brush head.
My brush head is not turning and with the lever set to engage the drive there is still considerable slack in the final drive belt.
There appears to be only a bearing deflecting the belt, should there be a pully or other device mounted on this bearing? There is so much slack a
ANSWER : Yes, there should have been a white plastic sprocket on top of the bearing – in its channel the belt would sit. Unfortunately no parts are available for this unit that can be bought retail – only available by order to dealer repair shops....
Unfortunately to fix it you must send it to one and that would be more expensive than a new one. Just junk this chinese POS and buy another chinese POS.
Unfortunately to fix it you must send it to one and that would be more expensive than a new one. Just junk this chinese POS and buy another chinese POS.
Read Full Q/A … : Bissell 8975 CleanView Bagless Upright Vacuum
Hi my proheat bissell 7901 stopped pumping water to the floor, but it pumps water from the hand hose. I read the manual and followed how to check belt and the flat belt on right side of shampooer is fine and I turned on and it turns and so do the brushes at the bottom of the machine. I was reading online and I guess there’s two belts on this machine? where can I find the other belt to see if it needs replacing. I guess it’s a ribbed belt? that is the water pump belt?
ANSWER : Just taken ours apart with the same problem… found it was caused by the 2 halves of the main casing coming apart in the area where the upright pedal release is. I found this to be due to the upper casing having broken in 2 places – the bottom of the screw wells..This means that the water tank cannot exert sufficient pressure on the valve to release the water..Only solution is a new top cover assembly
Read Full Q/A … : Bissell 8975 CleanView Bagless Upright Vacuum
