I have an Electrolux Aerus 2100 canister vacuum. When I

Vacuums\015 I have an Electrolux Aerus 2100 canister vacuum. When I insert the hose, it cuts off. The bag is new. It will run without the hose. When the hose is inserted the vacuum will come on and immediately cut off.\015

How to Identify and Fix Common Vacuum Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :

A few things you can check to try and solve:

Turn off the vacuum cleaner – then check if the nozzle, tube, hose or filters are blocked and/or dirty. Let the product cool down for a minimum of 2 hours on the charging stand before starting it again (stick vacuum cleaners only)

If the vacuum cleaner stops suddenly, the filters should be checked to make sure that they are not blocked or that they require changing. This applies to both bagged and bagless models. Also check if the nozzle or hose are blocked.

A vacuum cleaner can run continuously for 30 – 60 min each time. The vacuum cleaner has no suction power. For example, a hair cannot be sucked up.

Aerus is the successor to Electrolux USA, the iconic manufacturer of vacuum cleaners. However, the Electrolux name is now used in the U.S. by the Electrolux Group of Sweden, which until 2016 also manufactured Eureka vacuum cleaners.

Loose connections will cause your vacuum cleaner to lose suction. Make sure that the dust container, the hose, the tube and the brush are all attached properly. If the problem continues, your vacuum cleaner might have a technical problem. If you suspect this to be the case, contact an authorised service agent.

If your vacuum cleaner keeps turning off, this could be due to the following reasons: Blockages – check the hose and head for any obstructions. Filter – always check your filters, if these are clogged this could be causing the vacuum cleaner to work harder and lose suction power.

Vacuuming every day, or even a few times a day, is not going to create any long term problems. `But,` you might be thinking, `doesn`t the brushes spinning over the carpet on a beater bar wear it out? ` Sure, but a very small amount.

“We would recommend vacuuming at least once or twice a week—and more often if we have pets—with the right tools to remove dust quickly and effectively,” Patel advises.

Most owners believe that running their robot vacuums four times per week is sufficient to keep the floors dust-free. However, if you have children or pets, you should use your robot vacuum more frequently. Daily vacuuming is recommended if you suffer from seasonal allergies.

Electrolux is best known for its high-end appliances that are built to last.

Professional test companies regularly rank Electrolux as a top brand for laundry care; that is, they consider it the brand with the best cleaning ability with a gentle-on-clothes wash cycle. You can get a stackable washer and dryer from Samsung or Electrolux.

One of the easiest ways to increase vacuum cleaner suction is to empty the dust bag or container. Dust containers need to have enough space for airflow, otherwise, they could get clogged and have less suction power. Regularly check your dust compartment and empty or change it when it`s already 70-80% full.

The two main indicators to determine vacuum power performance are water lift and airflow. The water lift is measured in mmH₂O, mbar or kPa. It represents the suction force and is the reference parameter for vacuuming liquids and heavy materials. The airflow is measured in m³/h or in l/s.

Replace the Brush Belt

If the vacuum is still hard to push, tilt it back far enough that you can inspect the moving brush while the vacuum is running. Be careful to avoid getting too close to the moving parts. If you see that the brush is not turning, that means you will need to replace the brush belt.

The suction power is to be measured at the end of the tube of a complete vacuum cleaner (i.e. with tube, hose and filters – but without nozzle). Some manufacturers show the results from measurements made at the suction of the actual vacuum cleaner.

If you don`t vacuum your carpet, the dirt will break down carpet fibers and create a breeding ground for dust mites and bacteria. In addition, your home will begin to smell musty from the dirt, mites, and other organisms settling into the fibers.

If all you hear from the vacuum unit is a click at the when you try to start the vacuum motor from inside the house, then the motor in the unit is dead and has to be replaced. A strong odor from the shellac, which coats the copper coil windings, is an indicator that the motor is about to or has burnt out.

Check that the vacuum cleaner is plugged into a working power outlet and that fuses and breakers don`t need resetting. An activated thermal cut-out due to a blockage is the next most likely cause of the problem. Check for blockages in the hose and filters, and remove any obstructions that you find.

A damaged vacuum hose, clogged motor air filter or bad suction motor can cause the vacuum cleaner to shut off during use. A tripped overload on the vacuum suction motor can shut off the vacuum cleaner during use. If your vacuum has a reset button, push it; if the vacuum seems hot, let it cool off first.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

I had the vacuum cleaner question about the canister and the wand/powerhead… the Kenmore Progressive Vacuum canister model 116.25812 and the canister not powering off without unplugging the vacuum. The solution I received that they both run on their own switch so it is normal makes sense. However, is there a power switch on the canister anywhere? The only way for the canister to be turned off is by unplugging it. Any ideas? One would think there would be a switch. I am new to fixya and hope

ANSWER : Hi. On some models, one switch controls all of the power. Your issue, which is no working switch is almost certainly a blown triac on the circuit board in the canister – kenmore part number KC86WBZRZ000

Looks like a common fault with this particular model judging by the number of complaints on the web.
.
.Take it to your local vacuum repair shop and they should be able to fix it for a nominal fee.

Read Full Q/A … : Vacuums

I have an Electrolux Aerus 2100 canister vacuum. When I

ANSWER : It might be that the hose connections are bad.or it might be a sensor in the vacuum. call a electrolux vac shop and get it looked at.

Read Full Q/A … : Vacuums

When we turn on the vacuum, the canister falls open. The clips holding the canister in place do not seem to hold the canister tightly which I’m sure that it did in the past. The clips do not look bent, but every time we turn on the vacuum the intense pressure blows the canister open only remaining attached the the rest of the vacuum by one clip

ANSWER : Check filter and make sure it is kept clean at regular intervals. Possibly worn out clip retainers on cannister side due to excessive pressure build up. Do not force closure unless pressure is back to normal. May crack cannister or damage unit beyond repair.

Read Full Q/A … : Vacuums

Dirt devil vacuum cleaner–trouble vacuuming dirt and pet hair on carpeting –is the problem with the spinning brush which contacts the floor, not contacting the carpeting?? I thought (when I bought this vacuum) that the aforementioned brush was adjustable to various heights of carpeting. Sometimes, it seems like nothing is being vacuumed up –unless I have just put a new bag on the vacuum… Do I need or can I replace the spinning brush on the bottom of the vacuum so it kicks up and vacuums

ANSWER : Try replacing the belt. Rubber belts stretch out after about a year.

Read Full Q/A … : Vacuums

I purchased a brand new Eureka Pet vacuum, sorry don’t know exact name but it the one that has the self cleaning duster on it. Last night I used the vacuum on my carpet, it was working fine until I accidently sucked up the corner of a scarf that was hanging off a couch. I shut the vacuum off, pulled out the scarf and and resumed vacuuming. Much to my dismay the suction on the vacuum had ceased. Can you tell me if there is a reset button on the vacuum? The vacuum does not appear to be damage

ANSWER : If the motor is running, there should be suction. Possible problems depend on whether it’s a canister or upright and are:
.A clog in the hose, UR or canister. Detach hose. Drop small coin in one end and lift hose causing it to roll out the other. If it does, no clog in hose. Drop same coin into hose opening on power head. If it rolls out, no clog in PN.
.Broken fan blades, UR. Needs to be taken to shop for repair/replacement.
.
.A reset button is for use if the motor isn’t running, so won’t have anything to do with the suction.

Read Full Q/A … : Vacuums

Electrolux oxygen ultra vacuum manual – Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

ANSWER : You can find a downloadable pdf manual by using the following link.
.
.http://www.retrevo.com/search/v2/jsp/mytrevo/myTrevo.jsp?page=man

Read Full Q/A … : Vacuums

Electrolux Epic 6500SR Full Bag sensor working, Does not Reset properly

ANSWER : The problem was a sticking switch that was not being reset. The vacuum on/off switch mechanism is comprised of two switches. One is the main switch that turns the vacuum on and off. The second is a shut off switch that gets tripped when the full bag sensor is engaged. This second switch is supposed to get reset when you push the on/off switch on the outside of the machine. The full bag shutoff switch was stiff and it, therefore, was taking a couple of presses of the on/off switch to move the shutoff switch back into the running position.

Read Full Q/A … : Vacuums

I have a Kirby G4 Vacuum Cleaner – MOdel G4 D. I have never had any problems or repairs done to it in the past ten plus years that I’ve had it. This is an upright vacuum. I was vacuuming the carpet floor and was not having any trouble at all. I switched the vacuum off and moved it into a different room. When I tried to turn on the vacuum, it would not turn on. I checked with different outlets, used both front attachment and hose attachment. Checked the front part of the motor/ spiral case. This

ANSWER : Hello,
.My educated guess is that it’s either the switch or the power cord. Here are a couple of guides to help with diagnosis and repair…
.
.http://reviews.ebay.com/COMMON-PROBLEMS-WITH-THE-KIRBY-VACUUM-TROUBLESHOOTING_W0QQugidZ10000000003800312
.
.http://reviews.ebay.com/REPLACING-THE-POWER-SWITCH-ON-ANY-KIRBY-G-SERIES-VACUUM_W0QQugidZ10000000003752018
.
.Hope this helps!!
.Marci

Read Full Q/A … : Vacuums