brushroll and brushrol stopped working. It means vacuum is not working effectively now. Brushroll indicator is flickering.
Hoover Vacuums

How to Identify and Fix Common Vacuum Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :

Blockages or dirty filters may cause this to happen, the safety cut off will activate and switch off the electrical supply. If the cleaner has cut out, simply unplug and check for a blockage or dirty filters.
The most common cause of loss of suction is that the filters have become blocked. They may require cleaning or replacing. Another cause could be that the vacuum cleaner hose is blocked. First unplug the vacuum cleaner.
The powerful airflow from the vacuum can help shake dirt and debris loose and pull them into the vacuum. Without the fan, a vacuum couldn`t work at all. But the roller brush is critical, too. It`s necessary in dislodging deep dirt and stuck debris, and it helps clear a path for air to carry dirt into the vacuum.
A strong odor from the shellac that coats the copper coil windings is an indicator that the motor is about to or has burnt out. If the motor is still running, even if it turns on and off by itself as it is heating and cooling, you can still run the motor until it gives up for good.
The most common reason for vacuum motors failing is overheating. Most `dry` vacuums have a flow-though motor. These motors use the air they have sucked up the dust with, to cool themselves. When there is a blockage, flow-though motors are unable to cool themselves due to the lack of airflow.
Overheating motor causing an automatic shutoff

If a vacuum motor overheats due to poor airflow, the vacuum will automatically shut off. This is most commonly caused by an air passage that is plugged by hair or dirt. Refer to the leaky hose guide to remove the hose, then inspect for hair or dirt clogs.

If your vacuum cleaner turns on but won`t pick up on carpet or bare floors, something is impeding suction. You may need to change the vacuum bag, unclog the hose, replace/clean the filters, replace the hose, change the belt, or repair the motor.
Problems can occur when overused or clogged filters cause the vacuum motor to overheat. This not only shortens the motor life but causes a loss of suction. In some cases, total motor burn out can occur.
Putting in the incorrect amount of oil, putting in the wrong type of oil, and oil contamination can all cause the pump to not reach full vacuum. For this reason, you must check the oil regularly to ensure that it is not only clean, but also properly filled.
If your vacuum is set too high above the carpet surface, the vacuum can`t attract the gritty soil below. If the setting is too low, the vacuum`s beater bar or brushes can “fuzz” the carpet`s surface, causing it to look worn or frayed.
Push harder than you pull.

Many people naturally exert more force when they`re pulling their vacuums back than when they`re pushing them forward, but this can leave dirt on the floor. Vacuums are designed to be pushed forward at a rate of about 12 inches per second and pulled back at a rate of 6 inches per second.

If you`re smelling rubber, the belt has either burned out and snapped or the belt has become so stretched out that the roller is not moving and the vacuum belt is getting super heated from the motors RPM.
If the filter bag or canister is too full, it cannot pick up any additional particles and will simply jam or the motor will overheat and shut down. So, when you suspect your unit is about 75 per cent full, empty it!
Should the brush not rotate freely there may be debris tangled around the ends of the brush, carefully remove any obstructions or replace the brush with a new one. We recommend that you fit a new belt and brush once per year to keep your Reactive vacuum working efficiently.
`Tripped` reset systems are the most common reasons for a brushbar not turning, but there are some other less common reasons too. These include: If the bearings on the end of the brushbar have seized, you won`t be able to turn it at all. This will often result in a broken belt as well, so be aware of this.
`Tripped` reset systems are the most common reasons for a brushbar not turning, but there are some other less common reasons too. These include: If the bearings on the end of the brushbar have seized, you won`t be able to turn it at all. This will often result in a broken belt as well, so be aware of this.
The brush roll or its bearings may be clogged with hair, threads or dirt. Make sure they are clean and the roll spins. The belt may also have slipped because it was loose. Check the fit of the new belt when it is installed.
If you are finding that the brush head is not spinning or the light is not working, the contact patches between the main body, extension tube and the floor head may need to be cleaned. Ensure that the two connection points are clean and have no dust which could cause the connection to fail.
If you are finding that the brush head is not spinning or the light is not working, the contact patches between the main body, extension tube and the floor head may need to be cleaned. Ensure that the two connection points are clean and have no dust which could cause the connection to fail.
If you are finding that the brush head is not spinning or the light is not working, the contact patches between the main body, extension tube and the floor head may need to be cleaned. Ensure that the two connection points are clean and have no dust which could cause the connection to fail.
If you are finding that the brush head is not spinning or the light is not working, the contact patches between the main body, extension tube and the floor head may need to be cleaned. Ensure that the two connection points are clean and have no dust which could cause the connection to fail.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

We have a Bissell Proheat Cleanshot 2X Model 9500 Steam carpet cleaner. The first time we used it things were great. The second time we used it it left tracks in the carpet. We have no idea what caused this. We tried using the machine on an entirely different carpet and it did the same thing. After vacuuming the carpet about 10 or 12 times, the tracks are still embedded in the carpet – HELP!!!! We’re read and reread the manual and contacted customer service and received no help.
ANSWER : First things first. It’s only the second time you have used the machine, so it must be fairly new. If you have a receipt and the unit is less than a year old you should take it to an authorized Bissell repair center and have the machine inspected under warranty.
.
.Otherwise, The jets on this unit clog easily, there are two of them and you can locate them under the recovery tank towards the front of the machine, and blow them out with an air compressor. To prevent the jets from clogging in the future make sure to flush all shampoo out of the machine with clean water when done using it. That is most likely your problem.
.
.If it is leaving black streaks on your carpet it could be coming from a burnt belt or melted brushroller part, in which case inspect the belts and brushrollers and replace the damaged pieces.
.
.I hope this helped
.
.Good Luck

Read Full Q/A … : Hoover Vacuums

Carpet vacuum attachment quit working after sucking up a bedskirt. Bedskirt has been removed but carpet attachment will not work. My old vacuum had a reset button on the carpet attachment for use when the carpet attachment sucked up something and turned off. Does the Hoover have such a feature, and, if so, where is it? If not, how do I fix the problem and how do I keep it from recurring? Model # S3765-040. Serial # 100700081298. Purchased 2/08.
ANSWER : I have a Hoover Conquest approx. 4 yrs old. The turbo head is not working Model No. PB4 230-240V AC 50Hz 200w CS4901N (N127) I have been trying to locate another one or another one similiar to fit my machine

Read Full Q/A … : Hoover Vacuums

Dirt devil vacuum cleaner–trouble vacuuming dirt and pet hair on carpeting –is the problem with the spinning brush which contacts the floor,  not contacting the carpeting??  I thought (when I bought this vacuum) that the aforementioned brush was adjustable to various heights of carpeting.  Sometimes, it seems like nothing is being vacuumed up –unless I have just put a new bag on the vacuum… Do I need or can I replace the spinning brush on the bottom of the vacuum so it kicks up and vacuums
ANSWER : Try replacing the belt. Rubber belts stretch out after about a year.

Read Full Q/A … : Hoover Vacuums

How can I get my DAB radio working again?
I have a Sony XDRS100CD with DAB radio. The DAB radio has stopped working although I can still use the CD and get FM radio. The unit has a readout on the front that usually shows the time and this stopped working too, presumably because it got the time via the DAB radio.
The unit works from mains and batteries although I have only ever used it on mains.
ANSWER : I have the same problem… did you ever get a fix..
[email protected]

Read Full Q/A … : Hoover Vacuums

I have a DC 17. In the middle of vacuuming the vacuum stopped working when it was in the upright position. It only works when the head is down and i am using the bar. I can not use the extension bar, becasue when I put the vacuum upright it shuts off. Where is the problem?
ANSWER : Hi there, it’s Jack at Dyson.
.
. Like most Dyson vacuums, DC17’s main suction motor is protected by a thermostat which shuts the machine down if it starts to overheat. This could be due to a blockage, and the filter may also need a wash. If this occurs, the separate brush bar motor will still run if you recline the vacuum, and shut off when you stand the vacuum upright.
.
. The vacuum should reset itself automatically after it’s cooled down for around 2 hours. To prevent this from reoccurring, please wash the filter as shown in our video guide – in normal use this should be done at least once every 3 months. Use cold water without detergent, and allow the filter to dry completely for at least 24 hours before replacing it.
.
..Once you’ve done this it’s important to check the vacuum for any blockages – our Support guide will walk you through each checkpoint to make sure nothing is missed: http://www.dyson.com/support/dc17/dc17-allfloors/diagnosis-root-menu/dc17filterwashvid/flo-dc17-wand-suction
.
.This should resolve the issue. However if the issue reoccurs when the filter is clean and there are no obstructions in the airways, there could be an issue with the cyclone pack itself. If this is the point please contact us directly, as we’d appreciate the opportunity to provide further assistance. You can reach our experts by calling 0800 298 0298 (UK), 1-866-693-9766 (US), 1-877-397-6622 (CA) or 1800 239 766 (AU).

Read Full Q/A … : Hoover Vacuums

I purchased a brand new Eureka Pet vacuum, sorry don’t know exact name but it the one that has the self cleaning duster on it. Last night I used the vacuum on my carpet, it was working fine until I accidently sucked up the corner of a scarf that was hanging off a couch. I shut the vacuum off, pulled out the scarf and and resumed vacuuming. Much to my dismay the suction on the vacuum had ceased. Can you tell me if there is a reset button on the vacuum? The vacuum does not appear to be damage
ANSWER : If the motor is running, there should be suction. Possible problems depend on whether it’s a canister or upright and are:
.A clog in the hose, UR or canister. Detach hose. Drop small coin in one end and lift hose causing it to roll out the other. If it does, no clog in hose. Drop same coin into hose opening on power head. If it rolls out, no clog in PN.
.Broken fan blades, UR. Needs to be taken to shop for repair/replacement.
.
.A reset button is for use if the motor isn’t running, so won’t have anything to do with the suction.

Read Full Q/A … : Hoover Vacuums

My Bissell Pro Heat Select 2X does not pull up the dirt from the carpet into the water. The water just slowly disappears. The first time I used it the water got really dirty. The very next time I used it it worked differently and the water just disappeared until it was all gone. I’ve only used it a couple times and I don’t see where it is working. Has anyone else had this problem?
ANSWER : Inside the plastic suction lid is a little red plastic filter that has to be cleaned out every time you use it because it sounds like your vaccum is not picking up all the hair and debri before you clean the carpet causing the water to be injected into the carpet and disappearing and not filling the tank with dirty water. Steve

Read Full Q/A … : Hoover Vacuums

I have a kenmore progressive direct drive handi mate jr. upright vacuum. My daughter used it last night to vacuum up some cat litter that had spilled on the floor. I went to use it today and it turned on for a second and then stopped working. I have hit the reset button but it will not turn on. Help this vacuum is only 2 years old Is there anything that I need to reset or do so that the vacuum will work again?
ANSWER : Its probably clogged up with cat litter.might have gotten into the motor.your motor has a motor guard inside if it. when it overheats it will shut down till it cools off.you need to clean all th cat liter out of it.and clean the filters.with a direct drive you might want to take it in to a repairman to sevice. its not a shop vac i advise you not to pick up things like cat liter

Read Full Q/A … : Hoover Vacuums