Kenmore Vacuums
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
If the brushroll is sticking, it will cause too much friction and put too much strain on the belt. Remove the brushroll and clean all hair, string, and lint from the brushroll bearings. If the vacuum cleaner brush still doesn`t spin after you clean the brushroll, consider replacing the brushroll.
If you checked your brush roll, floor setting, and belt but your brush roll is still not spinning, that means you probably need a Shark micro switch replacement. This small switch tells the vacuums brush when to start spinning.
Clear the brush roll of any hair and debris and inspect by placing it on its end and spin. The brush should spin freely. If it doesn`t spin; it may be time to replace.
Inspecting the Vacuum Commutator for Motor Brush Problems
Test that by turning the motor off and pushing on the center shaft, the armature. If it has any play, besides spinning, then replace the motor. If solid then replace the brushes – motor brush replacement instructions.
The drive pulley connects to the washer drum and works with the drive belt and motor to rotate the drum. If the drive pulley is worn out, the drive belt might slip off, preventing the washer from spinning. Remove the drive pulley and inspect it. If the drive pulley is defective, replace it.
If the roller brush is not spinning, it cannot pick up dust. One reason could be that the power button is not set to position II, which runs the roller brush. If the button does not work, here is the link to the power button replacement guide. Another reason is that the roller brush could be broken.
To reset the Brush bar press the Brush bar control button twice or switch the machine off and back on. Please note: In normal use, the Brush bar automatically turns off when the machine is upright and automatically turns on when the machine is in the vacuuming position.
The brush thumbnail in the Tool Options bar reflects the brush changes as you adjust the brush dynamics options. You set brush dynamics options by selecting a brush tool and then clicking Brush Settings (or Advanced, for some tools) from the Tool Options bar. Controls the distance between the brush marks in a stroke.
There may be debris wrapped around the roller that is preventing it from turning. This is often due to hair, string, or other larger items that may be suck in the roller. Open the brushroll garage by sliding both of the release buttons away from you and then lift off the garage door.
Brushes. According to iRobot, brushes should be replaced every 6-12 months. Robot vacuums like the iRobot Roomba j7+ have multiple brushes that allow it to clean.
The two settings – brushes up and brushes down are to help you clean both carpets and hard floors. When the brushes are up you can get nice and close to carpeted floors and suck up all the dust and nasties hidden in the fibres.
Check that the vacuum cleaner is plugged into a working power outlet and that fuses and breakers don`t need resetting. An activated thermal cut-out due to a blockage is the next most likely cause of the problem. Check for blockages in the hose and filters, and remove any obstructions that you find.
Some of the reasons your washing machine drum is not turning could be a blocked drain pump, an overloaded or uneven wash load, worn-out motor brushes, a drive belt worn loose, an issue with the suppressor filter, low water pressure if excessive foam has been detected and when washing woollens.
If the drum stops spinning mid-cycle, try stopping the machine, draining the water and rearranging the laundry. You might be using too much detergent or an inappropriate type for your appliance. In this case, your washing machine will stop the spinning cycle and try to absorb the excess foam in its drum.
To reset your shark vacuum, put the Power button in the On-Off position and keep the vacuum unplugged. If necessary, clear the hose. Once it has cooled completely, plug the vacuum back in again.
Grab the clog with a pair of needle-nose pliers and pull it out. Open a pair of needle-nose pliers and feed it into the end of the lower hose. Once you feel the clog, pinch the blockage with your pliers to get a good grip on it. Pull the clog out of the hose and throw it away.
Fixing Frayed Brushes
The boiling water can help the bristles of the brush to lay flat and stop fraying. If the boiling water doesn`t work, you can trim and cut the ends of the brushes with scissors to give them a nice shape again.
New brushes are often shipped with a watersoluble “glue” holding the bristles together to prevent damage in shipping (even brushes shipped with a plastic cover over the bristles may have sizing in the brush). The bristles will feel hard and crusty, or maybe even be stuck together completely.
It`s located in the standard toolbar, and its default shortcut is the letter B. The Brush Tool works by adding a shaped mark on a layer, and if you continue pressing the mouse button or the pen on a tablet, several marks will be added, creating a stroke, until you release the pressure.
It`s easy to use the Brush tool to paint in your document. Simply locate and select the Brush tool from the Tools panel, then click and drag in the document window to paint. You can also press the B key on your keyboard to select the Brush tool at any time.
Open the Brush Panel from the toolbar or over the menu Window > Brush.
1. Motorized Brush Head. Sometimes called the “power nozzle,” this large attachment has a rotating brush to clean carpets more like an upright.
A Revolving Brush Roll Greatly Enhances Carpet Cleaning
Vacuum cleaners specifically designed to clean carpeted floors have motor or turbine driven revolving brush rolls with rows of bristles and sometimes beater bars as well. These brush rolls revolve at a very high speed, agitating the carpet fibers in the process.
The Shark Rotator Powered Lift-Away has one rotatory belt. The belt is responsible for the mechanical rotations of the brushroll. Without it, the vacuum will not function.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
Hoover WindTunnel Self-Propelled V Belt
ANSWER : I had this same problem with the V belt on my Hoover Vaccuum..
.There are three (3) basic things that will cause the brush roll not to spin..
.1. When handle is upright, brush roll is OFF..2. When switch is set for HARD surface, brush roll is OFF..3. Broken/worn FLAT belt or V Belt, brush roll will not spin.
.
.I noticed that the brush roll was not spinning when my vacuum was set for CARPET. After removing the cover I noticed that the V belt was loose, I thought the belt was worn so I purchased a correct replacement belt and installed it, but the new belt was also loose and when I turned the large flat belt pulley it did not turn the V belt pulley at the same time..
.I double checked the surface setting and I had the vacuum switch set for carpet, but still when I released the handle out of the upright position the brush roll would still not spin..
.My aggravation finally led me to this posting on FixYa’s website..
.The first thing I did was checked the screw to the left of the V belt as suggested by ejmjr5 and this did nothing to solve the problem or create more tension on the V belt, even when the upright handle was not in the upright position..
.After playing around with the surface setting control switch/nob I notice that when I moved the switch out of the HARD surface setting and over to CARPET, I had thought that the switch was set for CARPET as it visually appeared, but I was not pushing the switch over hard enough to click it into the CARPET setting mode..
.VOILA, the brush roll now spins correctly even though the V belt seams to be too loose for the pulley..
.You really have to force the switch into the CARPET setting. Be sure that you hear the switch/nob click into place..
.Now you can effectively clean up after that hangover of a party!.
.Burp!
.There are three (3) basic things that will cause the brush roll not to spin..
.1. When handle is upright, brush roll is OFF..2. When switch is set for HARD surface, brush roll is OFF..3. Broken/worn FLAT belt or V Belt, brush roll will not spin.
.
.I noticed that the brush roll was not spinning when my vacuum was set for CARPET. After removing the cover I noticed that the V belt was loose, I thought the belt was worn so I purchased a correct replacement belt and installed it, but the new belt was also loose and when I turned the large flat belt pulley it did not turn the V belt pulley at the same time..
.I double checked the surface setting and I had the vacuum switch set for carpet, but still when I released the handle out of the upright position the brush roll would still not spin..
.My aggravation finally led me to this posting on FixYa’s website..
.The first thing I did was checked the screw to the left of the V belt as suggested by ejmjr5 and this did nothing to solve the problem or create more tension on the V belt, even when the upright handle was not in the upright position..
.After playing around with the surface setting control switch/nob I notice that when I moved the switch out of the HARD surface setting and over to CARPET, I had thought that the switch was set for CARPET as it visually appeared, but I was not pushing the switch over hard enough to click it into the CARPET setting mode..
.VOILA, the brush roll now spins correctly even though the V belt seams to be too loose for the pulley..
.You really have to force the switch into the CARPET setting. Be sure that you hear the switch/nob click into place..
.Now you can effectively clean up after that hangover of a party!.
.Burp!
Read Full Q/A … : Kenmore Vacuums
Noise My Dyson DC08 is making a loud, rough, vibration/noise that seems to be coming from the from the rotating brush housing. I replaced the old belt which was several years old and slipping. When I run the motor with the new belt removed the machine sounds normal. The bearings on the rotating brush seem to be running smoothly when turned by hand both when out of the brush holder and when installed in the machine. I can’t find anything rubbing on the belt or rotating brush. I applied a bit o
ANSWER : Hi there, it’s Jack at Dyson.
.I’m sorry to hear you’re having difficulty with your Dyson vacuum. From your .description, it sounds like the model number you’ve supplied may not be correct, .as DC08 is a cylinder vacuum which doesn’t use a belt-driven brush bar. So we .can confirm exactly which model you own and take you through some quick .diagnostic checks, I’d encourage you to contact us directly. You can reach our .experts by calling 0800 298 0298 (UK), or 1-866-693-9766 .(US).
.We’ll .look forward to hearing from you.
.Best .wishes,
.Jack .- Dyson Official Online Customer Surpport
.http://www.dyson.com
.I’m sorry to hear you’re having difficulty with your Dyson vacuum. From your .description, it sounds like the model number you’ve supplied may not be correct, .as DC08 is a cylinder vacuum which doesn’t use a belt-driven brush bar. So we .can confirm exactly which model you own and take you through some quick .diagnostic checks, I’d encourage you to contact us directly. You can reach our .experts by calling 0800 298 0298 (UK), or 1-866-693-9766 .(US).
.We’ll .look forward to hearing from you.
.Best .wishes,
.Jack .- Dyson Official Online Customer Surpport
.http://www.dyson.com
Read Full Q/A … : Kenmore Vacuums
Windtunnel belt I have a new Hoover Windtunnel canister. The belt keeps coming off. It happened a couple weeks ago (several times after putting the belt back on) so I assumed I might need a new belt as it might have dried out at the store. I ordered new belts and today I used it for about an hour and the belt came off again, twice. There doesn’t seem to be anything to hold the belt on the stem as it seems to slip off. I have tried it centered, to the left and to the right….can you help. I am v
ANSWER : I’ve successfully used a compatible belt – Royal 104425001 .It’s still new, but for the time being at least – it works.
Read Full Q/A … : Kenmore Vacuums
Hoover WindTunnel, month-old belt, now too large to turn brush
ANSWER : I suspect you have been bitten by the Chinese bug..
.A very large percentage of replacement parts for all manner of appliances and vehicles are now being conterfeited in China who we should know by now has no respect for the intellectual property of others and a flood of low-quality stuff is being made as ‘knock-offs’ since they are generally easy to fabricate with fairly primitive means..Our eldest son just returned a supposedly ‘new’ steering pump for his (US) car but this one at least had China as the origin shown on the package..
.Make sure though that the brush roller turns freely and isn’t being impeded by trapped thread in the bearings.
.A very large percentage of replacement parts for all manner of appliances and vehicles are now being conterfeited in China who we should know by now has no respect for the intellectual property of others and a flood of low-quality stuff is being made as ‘knock-offs’ since they are generally easy to fabricate with fairly primitive means..Our eldest son just returned a supposedly ‘new’ steering pump for his (US) car but this one at least had China as the origin shown on the package..
.Make sure though that the brush roller turns freely and isn’t being impeded by trapped thread in the bearings.
Read Full Q/A … : Kenmore Vacuums
Floor Attachment I took off my floor attachment, but now the belt seems to be off and I can’t seem to get it back on right. I can’t use the attachment and I don’t know why it’s so hard to figure this out. They say, just turn it to belt off, but when i turn it it lift’s it up and can’t line up with the belt off label. Then, when I turn it the other way, it’s off. So I’ve been trying to pull it off so when it lines up with belt off, it’s off. But the I turn it the other way and it’s still off a
ANSWER : Try this,
.
.With the floor nozzle off the machine spin the belt lifter around until the red arrows match. If you look at the side that attaches to the vacuum you should be able to see the belt up on the hook. If is not on the hook offf the machine you will never get the belt on. Once the belt is on the hook attach the floor nozzle to the front of the machine. At this point you need to spin the belt lifter back to where the green arrows match. Oh and another suggestion make sure your hieght adjuster the pedals with arrows are all the way up. Hopefully that helps you out.
.
.With the floor nozzle off the machine spin the belt lifter around until the red arrows match. If you look at the side that attaches to the vacuum you should be able to see the belt up on the hook. If is not on the hook offf the machine you will never get the belt on. Once the belt is on the hook attach the floor nozzle to the front of the machine. At this point you need to spin the belt lifter back to where the green arrows match. Oh and another suggestion make sure your hieght adjuster the pedals with arrows are all the way up. Hopefully that helps you out.
Read Full Q/A … : Kenmore Vacuums
We have a Hoover upright vacuum cleaner, model Core 7. There is a switch that turns on and off the brush drive. This operates via a cam with a bearing putting pressure on the final drive belt to engage the brush head.
My brush head is not turning and with the lever set to engage the drive there is still considerable slack in the final drive belt.
There appears to be only a bearing deflecting the belt, should there be a pully or other device mounted on this bearing? There is so much slack a
ANSWER : Yes, there should have been a white plastic sprocket on top of the bearing – in its channel the belt would sit. Unfortunately no parts are available for this unit that can be bought retail – only available by order to dealer repair shops....
Unfortunately to fix it you must send it to one and that would be more expensive than a new one. Just junk this chinese POS and buy another chinese POS.
Unfortunately to fix it you must send it to one and that would be more expensive than a new one. Just junk this chinese POS and buy another chinese POS.
Read Full Q/A … : Kenmore Vacuums
Hoover windtunnel t series belt is loose- roller brush doesnt turn.
Its brand new belt is slipping. we bough new belts and putthem on same problem. Can not find solutio in manual.
Is the belt supposed to go around the “metal pulley”. I know it goes around the little metal motor thing, then thru the guide and around the brush.
What is the metal pulley??? Is is the larger round silver thing between the guide and roller?
Its brand new belt is slipping. we bough new belts and putthem on same problem. Can not find solutio in manual.
Is the belt supposed to go around the “metal pulley”. I know it goes around the little metal motor thing, then thru the guide and around the brush.
What is the metal pulley??? Is is the larger round silver thing between the guide and roller?
ANSWER : I also have a loose belt and have bought additional belts but have the same problem. I put the it around the metal rotor and around the brush roller a shown by he Hoover video, and it is loose.
Read Full Q/A … : Kenmore Vacuums
Hi my proheat bissell 7901 stopped pumping water to the floor, but it pumps water from the hand hose. I read the manual and followed how to check belt and the flat belt on right side of shampooer is fine and I turned on and it turns and so do the brushes at the bottom of the machine. I was reading online and I guess there’s two belts on this machine? where can I find the other belt to see if it needs replacing. I guess it’s a ribbed belt? that is the water pump belt?
ANSWER : Just taken ours apart with the same problem… found it was caused by the 2 halves of the main casing coming apart in the area where the upright pedal release is. I found this to be due to the upper casing having broken in 2 places – the bottom of the screw wells..This means that the water tank cannot exert sufficient pressure on the valve to release the water..Only solution is a new top cover assembly
Read Full Q/A … : Kenmore Vacuums
