How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
3 cleaning modes Power button Press the power button to start cleaning. Lean to clean Lean handle back to start a clean. Leave upright to direct suction to the wand. The wand or tools are attached to the end of the hose.
Your High Torque XL cleaner head has a slider control to adjust the suction of the cleaner head. To select the suction required, move the suction control slider on top of the cleaner head. For vacuuming durable floor coverings, hard floors and heavily soiled carpets and rugs.
Most cases of a jammed or stuck brush bar are quick and easy to fix, simply pulling the debris gently from the brush bar. Alternatively, if you need to clear a problematic blockage, you can take the brush bar out of the housing easily, for quick maintenance.
For the best experience, we recommend fully charging your machine, and any additional batteries, as soon as you open the box and after every clean. If you have additional click-in batteries, we recommend that you alternate the batteries to maintain even performance.
It`s important to fully charge the machine before using it for the first time, and after every clean. This helps to improve the algorithm`s accuracy. The battery is designed to be left on charge permanently, and this will ensure that the vacuum is fully charged when it`s next used.
A Dyson vacuum cleaner has a lifespan of around 10 years. This is considerably longer than most other vacuums. So, if you`re looking for a high-quality vacuum cleaner that will last you for a long time, a Dyson could be a good choice. However, remember that Dyson vacuums are expensive.
To reset the Brush bar press the Brush bar control button twice or switch the machine off and back on.
The Dyson V6 is designed so that you can store the unit on the charger. Storing the Dyson on the charger will not harm the battery and it is not necessary to use the unit until the battery is depleted.
Give it a break
By letting the battery run down to empty at least once a month, you`ll help to prolong its life.
Yes, you can just plug the charger into an outlet and into the vacuum head.
The blue LEDs – one on each side of the battery – will flash on and off during charging. When the battery is charged, both LEDs will light for 5 seconds, then go out. The screen will also show the battery charge level at 100%. The machine can take up to 4.5 hours to fully charge.
Another issue that can arise, is that the machine will feel hard to push. Thus is due to the machine`s suction forming an air tight seal between the cleaner head and the floor. It`s usually more common on thicker, more plush carpeting, carpets with thicker padding underneath or even area rugs.
Check the LED light to determine the battery level. A solid blue light indicates that the machine is in normal operating mode. A flashing blue light indicates that there is no power, and the battery needs to be charged for a minimum of 3.5 hours.
If you find that your machine is turning off intermittently, the filter in your vacuum is most likely full and covering the ventilation system. Remove the filter, then empty and wash it. Allow the filter to dry for at least 24 hours, or until it is completely dry.
First check the airflow valve located under the handle. Sliding this open may make it easier to push your vacuum. It could also be that your suction is set too high. To fix, use the suction controls on the canister to adjust the suction settings.
The cleaner head housing is not washable and should only be wiped over with a damp lint-free cloth. To maintain optimum performance, check and wash your brush bar regularly. Make sure your machine is disconnected from the charger and take care not to touch the trigger.
`We do not recommend that owners expose their machines to water`. Dyson is urging customers not to clean their vacuum cleaners by leaving them in water, after a hack went viral online.
Wash filters in cold water only
(don`t use detergent or wash in a dishwasher or washing machine). Rinsing under the water supply then gently squeezing the water out of the filter. Repeat until the water runs clear.