Kirby G4 Bagged Upright Vacuum

How to Identify and Fix Common Vacuum Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :

Remove the brushroll and clean all hair, string, and lint from the brushroll bearings. If the vacuum cleaner brush still doesn`t spin after you clean the brushroll, consider replacing the brushroll.
The air filter traps particles as the air travels through the vacuum cleaner. If the filter is clogged, the vacuum cleaner will not have proper suction. If your vacuum filter is clogged, refer to your owner`s manual for cleaning instructions.
The brush roll or its bearings may be clogged with hair, threads or dirt. Make sure they are clean and the roll spins. The belt may also have slipped because it was loose. Check the fit of the new belt when it is installed.
Kirby vacuum cleaners are made of die cast aluminum where most other vacuums are made of plastic. This makes the Kirby vacuum more durable than other model on the market. This is why the average lifespan of a Kirby is over 30 years.
The most common problem with a vacuum cleaner is also the easiest to remedy: clogs in the hose or attachments. Also the electrical cord, motor, switch, fan, brushes, and motor bearings can all need repair or replacement. The drive belt may need replacing; and the attachments, hoses, and filters may need unclogging.
Often, a belt breaks because the machine is running over the edge of a rug or other thick items, perhaps even the vacuum cord. This causes “snagging.” When this happens, the belt becomes stuck and usually overheats. Unfortunately, this results in immediate breakage.
Unlock the Handle Tilt Latch Lever before pulling backwards. Failure to follow this notice could result in damage to the floor. For carrying: Move the Handle Tilt Latch Lever away from the bag to lock the base in place when the unit is lifted off the floor.
The Dyson vs. Kirby vacuum cleaners debate can be complicated, as these brands are so different. If it comes down to price or size, Dyson will probably get the upper hand — but for all other vacuuming considerations, Kirby is the way to go.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

I need a manuel to replace a broken fan on my g4 kriby
ANSWER : Hello,

We have actually recorded a very informative do it your self video on how to replace the fan on a Kirby Generation upright.

The video is a two part video, but this explains step by step how to remove the old fan, and put the new one on.

If you need to purchase a new fan assembly, here’s a link to the Fan assembly for your Kirby G4. Unfortunately you may only purchase them as a complete assembly:
Genuine Kirby Vacuum Fan. Kirby Part # 119096S

Here’s the videos showing how to replace the fan:

Part 1:

Part 2:

Hopefully this helps you with your problem! If this did help, please be so kind and rate the repair, or leave feedback for me. This is very appreciated by the Fixya community when someone is able to answer your question, and assures that experts continue to answer free questions, instead of just the premium paid questions.

Thanks again!

Chris Jones
GoVacuum.com

Read Full Q/A … : Kirby G4 Bagged Upright Vacuum

KIRBY G4 FAN ASSEMBLY ORDER
ANSWER : First put the gasket on the spacer, thin end to to out, push it down all the way on the motor shaft, then put the nylon washer on, then the fan, metal washer and then the pulley, just snug it, (don’t tighten too much just beyond hand tightening). Put the casing, top and handle back on.

Read Full Q/A … : Kirby G4 Bagged Upright Vacuum

Hoover Wind Tunnel U6458-900
Self Propel doesn’t work – via other expert advice here for other models of Hoover – I’m thinking it is the actuator that needs to be replaced as I can see the cable does not connect to anything on the bottom. My problem is – I can’t get the cover off. Been trying for a couple of hours. I removed every screw I can seem to find but something is hold it down. I also am wondering if/when I do eventually get the cover off, would I need to replace the cable when I replac
ANSWER : On some models there are hook/springs that hold the cover of the base snug.

Read Full Q/A … : Kirby G4 Bagged Upright Vacuum

My older Dyson DC14 (the purple one) early model with a clutch on the beater bar belt needs a clutch replacement. The bar has been cleaned and there are no worn or damaged parts so I conclude that the clutch at the motor end of the belt needs to be replaced. I can find the part online but no instructions on how to disassemble the vacuum to get to and replace it. Dysons only advice is to give me the address and phone of the nearest service center. Can you help me?
ANSWER : Have a look at www.dysonmedic.com which has some very useful info on dismantling and repairing Dysons.
.
.Although this site doesnt actually cover the DC14 yet, the DC14 is very similar to the DC07 so as regards dissassembling the machine, and replacing the clutch, my experience is that the DC07 info will enable you to do the job.

Read Full Q/A … : Kirby G4 Bagged Upright Vacuum

Kirby Lexan Fan is crack and need help to replace
ANSWER : Hello…
.Check out my online instructions…
.
.http://reviews.ebay.com/KIRBY-VACUUM-REPAIR-HOW-TO-REPLACE-THE-FAN-IMPELLER_W0QQugidZ10000000003711302
.
.Hope they help!
.Marci

Read Full Q/A … : Kirby G4 Bagged Upright Vacuum

My wall ceiling fan’s control unit UC 9051T failed. Light switch button does not work. If I replace it with some generic universal unit, do I need to replace transducer located in the fan housing also, or all of them are compatible? Thanks in advance. M
ANSWER : First, you didn’t say you checked that the bulb worked. Is that burned out?
.
.If bulb is ok, you will have to make sure the switch is matched with the fan (ususally a set of 4, 6 or 8 micro-switches have to be set the same in both switch and fan to be on same frequency of communication – even if you have an exact US 9051T controller).
.
.A whole new fan is not too expensive ($100) and may be best route if you use the fan alot and it is over 7 years old – just an option.
.
.Also, just because the light doen’t work doesn’t mean it is the switch transmitter that is broken, it could also be the receiver. Call the company on the website below – they will either tell you how to check or you can send everything to them and they will check for you.
.
.http://www.eceilingfans.com/
.
.Sorry for making it so difficult – I hope it is just your bulb.
.
.-Mark

Read Full Q/A … : Kirby G4 Bagged Upright Vacuum

I need to fit a new fan to my kirby g4 but
ANSWER : I wouldn’t recommend doing this yourself. If you had to ask how, that’s proof you shouldn’t bite this one off. Take it to a vac shop. This is a very involved repair. A vacuum professional can easily do it, but it would cause you great stress and heart acke

Read Full Q/A … : Kirby G4 Bagged Upright Vacuum

I need to replace the fan and am not sure Kirby G 4 A
ANSWER : Greetings from GoVacuum,
.
.We’ve shot a video showing you detailed instructions on how to replace the fan on a Kirby Generation vacuum cleaner. The video is in two parts below. If this video was helpful to you, please be sure to rate this Solution by clicking the four Thumbs Up icons in the top right hand corner of this Solution;
.
.Changing the Fan On a Kirby Generation Video, Part 1:
..Kirby Fan Change Video Part 2;
.
.
.

.
.Thanks,
.
.Chris Jones
.GoVacuum.com

Read Full Q/A … : Kirby G4 Bagged Upright Vacuum