Eureka 3041BZ Upright Vacuum

How to Identify and Fix Common Vacuum Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :

Because vacuum manufacturers do not share a standardized naming system for vacuum belts, using your vacuum`s model number is the best way to ensure an accurate belt order.
Most Belts are normally measured from where the belt leather folds at the buckle end to the middle hole at the tip end and are usually stamped on the back of the belt with the size example 32, 34, 36 etc.
You will find your model number on a metallic silver sticker. It`s usually located on the back or bottom of the vacuum cleaner.
Belt powerfully rotates the brusher bars in your upright vacuum. For optimum performance, change the belt at least every 12 months.
Vacuum belts work to spin a vacuum`s brush roller and/or, on some self-propelled models, to turn a vacuum`s wheels. Whatever the style of vacuum, this repair will take placein the machine`s brushroll area.
For most cars, the belt will be located at the front of the engine. When checking the belt, always make sure the car is switched off and cooled down. Your belt should be inspected with each oil change. Mechanics will normally check the belt to ensure no significant damage has occurred.
Multiply the inch measurement by 2.54 to find your belt size in cm. Men`s pant sizes are usually one size smaller than their belt size. For example, a 36-inch waist will correspond to a 38-inch belt size.
Eureka is a brand owned by Chinese company Midea Group that manufactures vacuum cleaners, including uprights, cordless, canisters, sticks and handhelds.
Our Verdict On Eureka Vacuum Reviews

Eureka vacuum cleaners are one of the most popular brands based on consumer reviews. Their 4870 Boss upright vacuum cleaner has been getting rave reviews based on its performance, maneuverability and durability.

Next to the motor, the belt on your vacuum is just about the most important part of your vacuum. Without the belt to spin the brushroll, most vacuums won`t pick up on carpeting at all! If your vacuum uses a rubber belt, check it once a month for cracks, melting, and especially, slippage.
You should replace the belts on your vacuum at least every three to six months if the vacuum is regularly used. This is very important for proper cleaning.
If your vacuum runs but isn`t always picking up dirt, it might be time to change the belt. Consumer Reports` experts reveal how fast and simple it is to install a new belt which can save you a trip to the repair shop.
Vacuum cleaners are fairly simple machines. They need power to be transmitted to the vacuum to create a suction force that lifts debris. So, the usual areas that cause suction loss include the wrong height setting, stuck rollers, a faulty gasket, a broken vacuum belt, a filled bag, or a clogged hose.
If the brushroll is sticking, it will cause too much friction and put too much strain on the belt. Remove the brushroll and clean all hair, string, and lint from the brushroll bearings. If the vacuum cleaner brush still doesn`t spin after you clean the brushroll, consider replacing the brushroll.
Since you`ll likely only replace your serpentine belt once during the life of your car, it`s generally recommended to take your car to a professional mechanic. You can do a lot of damage to your vehicle if you drive on the road with an improperly installed serpentine belt.
Belt repair can be complex, as each job is custom and completed by hand. Often, our craftsmen must sew through thick layers of leather to make a delicate repair.
There are two belts you need to be familiar with when talking about car maintenance — the serpentine belt and the timing belt. The serpentine belt winds through your engine and carries power to several key components, including the alternator, air conditioning, and power steering pump.
There are three common V belt types: Classical V-belt (classified by their dimensions from A to E), Narrow V series (ranked by their sizes 3V, 5V, and 8V), and light-duty Fractional Horsepower belt (classified by their dimensions 2L, 3L, 4L, 5L). The letter X classifies their counterpart cogged belt.
Serpentine Drive Belts

The most common belt in the modern car and responsible for most of the functions in your vehicle, the Serpentine Belt replaced the multi-belt V-belt system. The serpentine is one belt that winds throughout the entire engine transferring power.

Most cars have somewhere in the range of 1-3 drive belts: the Serpentine belt, V-belt, and Timing Belt. it is important to understand the purpose of each drive belt to be able to recognize when it is not functioning properly.
The serpentine belt goes by a couple of different names: accessory belt and drive belt. The belt is long and snakes through several pulleys. That`s why it`s called a serpentine belt. You can find the serpentine belt on the front or side the engine.
There is no one-size-fits-all belt sizing formula. Belts fit differently depending on user sizes and gear combinations. For instance, gun belts measure different standards than a regular size guide due to the flexibility of various holsters. The intended use influences your choice of shapes and even material.
This industry standard number, frequently denoted as the “PK” number, is printed next to the manufacturer`s part number on almost every serpentine belt produced, and can be seen in the examples below. WHAT IS A “PK” NUMBER? A “PK” number is a worldwide standard metric belt measurement printed on most serpentine belts.
Are Women Belt Sizes Same as Men? There isn`t any significant difference between both. However while Men`s belts come in waist sizes between 27-48 inches, the sizes available for women are between 24-44 inches.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

I’m using (or WAS using) a Eureka ”the boss” model 8803. The belt broke, no biggie, so I replaced it with a Eureka model U belt, the problem is when I put the new belt on and turn on the vaccuum, the belt breaks again. I am also having trouble getting the brush roller to fit right when the belt is in place. I can’t find any sharp edges that would cut the belt,nor can I find where any small bits may have broken. Anyone have a solution for me?
ANSWER : First, make sure you have the right belt, second, i am thinking that you are not lineing the roller up right, it will only fit one way. look at the ends of the roller and the grooves where it slides in, you should be able to see clearly how it goes.

Read Full Q/A … : Eureka 3041BZ Upright Vacuum

Hi my proheat bissell 7901 stopped pumping water to the floor, but it pumps water from the hand hose. I read the manual and followed how to check belt and the flat belt on right side of shampooer is fine and I turned on and it turns and so do the brushes at the bottom of the machine. I was reading online and I guess there’s two belts on this machine? where can I find the other belt to see if it needs replacing. I guess it’s a ribbed belt? that is the water pump belt?
ANSWER : Just taken ours apart with the same problem… found it was caused by the 2 halves of the main casing coming apart in the area where the upright pedal release is. I found this to be due to the upper casing having broken in 2 places – the bottom of the screw wells..This means that the water tank cannot exert sufficient pressure on the valve to release the water..Only solution is a new top cover assembly

Read Full Q/A … : Eureka 3041BZ Upright Vacuum

My older Dyson DC14 (the purple one) early model with a clutch on the beater bar belt needs a clutch replacement. The bar has been cleaned and there are no worn or damaged parts so I conclude that the clutch at the motor end of the belt needs to be replaced. I can find the part online but no instructions on how to disassemble the vacuum to get to and replace it. Dysons only advice is to give me the address and phone of the nearest service center. Can you help me?
ANSWER : Have a look at www.dysonmedic.com which has some very useful info on dismantling and repairing Dysons.
.
.Although this site doesnt actually cover the DC14 yet, the DC14 is very similar to the DC07 so as regards dissassembling the machine, and replacing the clutch, my experience is that the DC07 info will enable you to do the job.

Read Full Q/A … : Eureka 3041BZ Upright Vacuum

The original belt on my upright Kenmore Progressive broke and I replaced it with the spare that was in the vacuum. The vacuum and spare belt are about 10 years old. Then the spare broke after one vacuuming session and there was a burning smell coming from the vacuum. I ordered new belts and replaced it with the new belt. It seems to be working fine with no smell. I checked the belt after I vacuumed the family room and although it was in tact, the belt was very hot. Is that normal? Should t
ANSWER : The belt heats up due to the friction, as well as being in contact with the shaft of a hot motor. It is normal.

Read Full Q/A … : Eureka 3041BZ Upright Vacuum

Windtunnel belt I have a new Hoover Windtunnel canister. The belt keeps coming off. It happened a couple weeks ago (several times after putting the belt back on) so I assumed I might need a new belt as it might have dried out at the store. I ordered new belts and today I used it for about an hour and the belt came off again, twice. There doesn’t seem to be anything to hold the belt on the stem as it seems to slip off. I have tried it centered, to the left and to the right….can you help. I am v
ANSWER : I’ve successfully used a compatible belt – Royal 104425001 .It’s still new, but for the time being at least – it works.

Read Full Q/A … : Eureka 3041BZ Upright Vacuum

Hoover WindTunnel Self-Propelled V Belt
ANSWER : I had this same problem with the V belt on my Hoover Vaccuum..
.There are three (3) basic things that will cause the brush roll not to spin..
.1. When handle is upright, brush roll is OFF..2. When switch is set for HARD surface, brush roll is OFF..3. Broken/worn FLAT belt or V Belt, brush roll will not spin.
.
.I noticed that the brush roll was not spinning when my vacuum was set for CARPET. After removing the cover I noticed that the V belt was loose, I thought the belt was worn so I purchased a correct replacement belt and installed it, but the new belt was also loose and when I turned the large flat belt pulley it did not turn the V belt pulley at the same time..
.I double checked the surface setting and I had the vacuum switch set for carpet, but still when I released the handle out of the upright position the brush roll would still not spin..
.My aggravation finally led me to this posting on FixYa’s website..
.The first thing I did was checked the screw to the left of the V belt as suggested by ejmjr5 and this did nothing to solve the problem or create more tension on the V belt, even when the upright handle was not in the upright position..
.After playing around with the surface setting control switch/nob I notice that when I moved the switch out of the HARD surface setting and over to CARPET, I had thought that the switch was set for CARPET as it visually appeared, but I was not pushing the switch over hard enough to click it into the CARPET setting mode..
.VOILA, the brush roll now spins correctly even though the V belt seams to be too loose for the pulley..
.You really have to force the switch into the CARPET setting. Be sure that you hear the switch/nob click into place..
.Now you can effectively clean up after that hangover of a party!.
.Burp!

Read Full Q/A … : Eureka 3041BZ Upright Vacuum

Replace belt i need to replace the belt on an upright dirt devil 086310 vaccume but do not have a manual and can not find how to open the assy to replace the belt
ANSWER : On the bottom, there should be a few screws to remove to remove the plate covering the brush roll. However some may have screws on the top housing to remove the top.

Read Full Q/A … : Eureka 3041BZ Upright Vacuum

Belts I have a Hoover self-propelled windtunnel, purchased 6-04. It gets light use. I have replaced the v belt 3 times, once under warranty, and it must be replaced again. It appears to be in very good condition, but is stretched too big. When I purchased 2 v belts a year ago, one was already too stretched,but when my Dad took it back, the salesman put it on another model and said it was fine (Dad never mentioned this to me). Is there a way to adjust the vacuum to hold the belt tighter? Do t
ANSWER : It is the flat belt that gets stretched and should be replaced at least every 6 months. The V belt wears down so it won’t it right in the brush roll V. Maybe the belt tensioner wheel has a problem, sometimes they get hook up and won’t engage the V belt. Check the brush roll also, if where the V belt rides in is covered up with belt, replace it. There is no adjustment, doesn’t need it if everything is working the way it should.

Read Full Q/A … : Eureka 3041BZ Upright Vacuum