Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
There are two variations of the Dyson DC17 belt, the 8mm wide version, and the 10mm wide version. Other than the widths the two belts are the same. The 8mm wide belt replaces Dyson part numbers 911710-01 and 11710-01-01, and the 10mm wide belt replaces Dyson part number 11710-01-02.
Dyson Belts, Fits: All Upright Vacuum Cleaner Models Using one Belt System, 3 Belts in Pack.
Look for a control knob on the front right hand side of your Dyson vacuum. If your machine has a knob it is a clutched model. If your machine does not have a knob it is a non-clutched model.
The Dyson DC17 is an upright cleaner launched in October 2006 in the US.
Because vacuum manufacturers do not share a standardized naming system for vacuum belts, using your vacuum`s model number is the best way to ensure an accurate belt order.
A Dyson vacuum cleaner has a lifespan of around 10 years. This is considerably longer than most other vacuums. So, if you`re looking for a high-quality vacuum cleaner that will last you for a long time, a Dyson could be a good choice. However, remember that Dyson vacuums are expensive.
If your agitator brush roll on your Dyson DC07 isn`t turning correctly even though the motor runs smoothly, a snapped or worn out drive belt may be causing trouble. If the drive belt in your vacuum cleaner has either perished or damaged, don`t fret it`s fairly simple to replace.
Serpentine belt replacement is easy because today`s automatic drive belt tensioners eliminate the need to loosen bolts or pry components into position for retensioning. Just rotate the tensioner, remove the old belt and install a new one.
The cost of the serpentine belt itself could be around $50 and the cost of labor could be around $150. As a result, a serpentine belt cost for replacement could range from $70 to $200 depending on your exact model and where you get it replaced.
Today, most serpentine belts are expected to last anywhere from 60,000 to 100,000 miles. Some belts can last significantly longer than this, while others give out before 60,000 miles. Make sure to check your owner`s manual to find out the recommended belt replacement time frame.
Belts range in size from small, detail-type sanders with belts that are only an inch or two wide to heavy-duty 4″ x 24″ machines. A common size for home shop use is a 3″ x 21″ sander. This size offers a sizeable sanding area, without the fatigue generated by running a large machine.
Sanding belts that are well cared for can last for one or two years if they are stored away from moisture, condensation, excessive cold, or excessive heat. All of these factors can contribute to joint deterioration, so store your belts in a climate-controlled environment.
A typical price for Vacuum Belts is $6 but can range from approximately $4.99 to $26.
Often, a belt breaks because the machine is running over the edge of a rug or other thick items, perhaps even the vacuum cord. This causes “snagging.” When this happens, the belt becomes stuck and usually overheats. Unfortunately, this results in immediate breakage.
If there is a strong burning smell coming from the motor area of your Dyson DC14 or DC07 then it is most likely that your motor has burnt out.
Dyson was designed and patented by a British, had it made in Malaysia (Johor Bahru), – as it is cheaper to make here.
In short, our vacuums are built to last. But what does “built to last” mean? We put our machines through at least five years of testing in harsh conditions to ensure we`re engineering the most robust machines.
Which Dyson vacuum is the most powerful? In terms of sheer suction power, the Dyson Ball Animal 3 Extra is the most powerful option in Dyson`s current lineup, offering 290 AW, or air watts, of suction power. Among the brand`s cordless stick vacuums, the Dyson V15 Detect is the most powerful, with a rating of 230 AW.
Take your existing pants size and then add two inches to the number. For instance, if your pants waist size is 38, then your belt size would be 40. You can also find your belt size by measuring a belt you already own that fits well.
If your vacuum`s belt is misaligned, it may cause unusual sounds and smells like burning rubber due to a build-up of friction and heat. Use the Dyson Ball Animal Brushbar Replacement Guide to remove the vacuum`s brush bar and view its belt.
Most problems arise because of a blockage – if not a dirty filter or cyclone unit, then something could be caught in the wand or the brush bar. Once again, the lack of suction could be caused by a dirty filter or a blockage somewhere in the vacuum`s system.
Check the LED light to determine the battery level. A solid blue light indicates that the machine is in normal operating mode. A flashing blue light indicates that there is no power, and the battery needs to be charged for a minimum of 3.5 hours.
Belts should never be stored above 115°F. Belts will begin to degrade after 7 years even when stored properly. Beyond seven years, assuming normal storage, a decrease in service life of approximately 10% per year can be expected.
Missing cogs can cause belts to slip and fail, when it is discovered there are teeth missing, the belt should be changed immediately. The most common reasons your belt could be missing a cog are excessive heat, the pulleys are too small or misaligned. It can also be caused by improper or prolonged storage of belts.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
The original belt on my upright Kenmore Progressive broke and I replaced it with the spare that was in the vacuum. The vacuum and spare belt are about 10 years old. Then the spare broke after one vacuuming session and there was a burning smell coming from the vacuum. I ordered new belts and replaced it with the new belt. It seems to be working fine with no smell. I checked the belt after I vacuumed the family room and although it was in tact, the belt was very hot. Is that normal? Should t
ANSWER : The belt heats up due to the friction, as well as being in contact with the shaft of a hot motor. It is normal.
Read Full Q/A … : Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
I need to replace drive belt on dyson dc17 – Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
ANSWER : Here is a link to the belt you need and a manual you can view which has instructions:
Read Full Q/A … : Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
Changing belt on a dyson DC17 Animal – Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
ANSWER : This video should help you out. .
.
.
Read Full Q/A … : Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
Replace belt on dyson animal – Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
ANSWER :
Read Full Q/A … : Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
Bissell Power Track Cyclonic Upright Bagless Vacuum.. ..The spin brush works laying down….when upright it won’t spin! I cleaned any and all hair from the roller….belt is not broken….but do I need a new belt though? The vac is a few years old bever replaced the belt yet.
ANSWER : You need a new belt.
Read Full Q/A … : Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
The belt on my Dyson vacuum keeps breaking – Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
ANSWER : SWITH OFF POWER AT SOCKET AND REMOVE
.
.REMOVE BOTTOM PLATE IF COMPETENT TO DO SO REMOVE ROLLER ASSEMBLY REMOVE ONE SIDE OF BEARING COVER AND SLIDE OUT AXLE CLEAN BOTH BEARING COVERS OF DUST AND DEBRIS ALASO FIRST CHECK FOR ITEMS JAMMING BELT OR ROLLERS REFIT.
.
.REMOVE BOTTOM PLATE IF COMPETENT TO DO SO REMOVE ROLLER ASSEMBLY REMOVE ONE SIDE OF BEARING COVER AND SLIDE OUT AXLE CLEAN BOTH BEARING COVERS OF DUST AND DEBRIS ALASO FIRST CHECK FOR ITEMS JAMMING BELT OR ROLLERS REFIT.
Read Full Q/A … : Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
Wiring diagram for dyson dc17 vacuum – Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
ANSWER : Hi Manny,
Thank you for your inquiry. We recommend that any repairs that involve the electrical components of your DC17 be carried out by an authorized repair technician. Please call us at 0800 298 0298 (UK) or 1-866-693-9766 (US) so we can provide further assistance. We look forward to speaking with you.
Best wishes,
Jessica
Read Full Q/A … : Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
Replacing clutch drive belt dyson dc14 – Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
ANSWER : Chris,
.I am just trying to find an owners manual, but I can not find one anywhere. Your link did not work. Can you help with another link?
.I am just trying to find an owners manual, but I can not find one anywhere. Your link did not work. Can you help with another link?
Read Full Q/A … : Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
