Kenmore 31912 Progressive Direct Drive Bagged Upright Vacuum\015 One of the prongs broke and I want to replace the entire cord. .There are only 3 visible screws but when they are removed the housing.doesn’t release to get to the connection inside.\015

How to Identify and Fix Common Vacuum Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :

If your vacuum will not turn on and the power cable/connector is faulty, use this guide to replace the power cable/connector. You will need wire strippers, wire end caps, and the T10 and T20 Torx Screwdrivers. Reassembly requires rewiring.
It`s also important to pay attention to the vacuum cords. Tishko recommends checking them daily. Replacing a cord might cost $85 in labor and up to $130 for the new part.
If only the plug prongs are bent or snapped, start by replacing the plug. If the cord itself is frayed or has exposed wiring, you`ll need to replace the entire electrical cord. Replacing only the plug could leave you open to electrical shock.
This product is 220 volts / 240 volts for use overseas outside North America. These items will not work in North America with 110 volts. Special Discount! Save 5%!
Regardless if a cord is damaged by age, heavy use, pinching, or bearing too much weight (when an appliance is hung by its cord), a damaged cord increases the risk of electrical shock, fire, or electrocution, and should NOT be used. “The electric cord on your appliance contains a live wire that is securely insulated.
If your pet chewed near the end of the cord close to the plug, cut the cord. Then you can replace the plug. If your pet chewed in the middle of the cord, cut out the chewed section and splice the two cords together. If the cord is chewed closer to the appliance, replace it with a new cord.
As a general rule, if the repair is going to cost less than half the cost of a new vacuum cleaner, it`s best to go ahead and get it repaired. When the service tops half the price of a new machine, it`s probably best to invest in a newer model.
Most vacuum models including brands like Oreck feature models with a 30-foot cord. A cord of this length allows vacuum users to maneuver around their home and complete cleaning needs with ease.
The green wire is the ground wire, the white wire is the neutral wire, and the black wire is the hot wire. Light-duty interior extension cords often lack the ground wire, but if a ground wire is present, be sure to connect it.
Simply put, power cords that fail, no matter what the reason, are safety hazards, damaging appliances and causing fires. So, once again, the “when to replace it” answer is every 5 years.
Recycling Power Cords

To recycle your old cords, e-waste facilities are your best option. Many communities now have dedicated e-waste recycling facilities, either run by private companies or by the local government. Best Buy is another popular e-waste recycler, and power cords are just one type of item they accept.

Using a heat gun, some soldering wire, and a cutting tool, you can fix the faulty or broken wires, and restore your laptop`s charger to working condition.
Shark 10.8-Volt Cordless Handheld Vacuum.
As a central vacuum manufacturer we use the 120 and 240 volt motors. The 120 and 240 motors will not be adversely affected if used with lower voltages. The 120 volt motor will be fine on 110 volts. Likewise, a 240 volt motor will be fine on 220 or 230 volts.
The charger`s voltage is 28.8V. There are several different versions of Shark series vacuum.
You can also leave a spare battery on charge, so you always have one ready to go when the one in your vacuum runs out. It`s easy to purchase additional batteries directly from Shark. Should I buy a refurbished or reconditioned vacuum cleaner?
Lightweight. Agile. Dynamic Technology is an innovative combination of 3 elements, delivering a powerful, comfortable clean throughout your whole home. The pod design features 175 air watts of powerful suction* in an extra-lightweight 4kg design – so light it can easily be lifted to clean stairs.
Extension cords can overheat and cause fires when used improperly. Overheating is usually caused by overloading or connecting appliances that consume more watts than the cord can handle. Damaged extension cords can also cause fires.
Damaged wires and cables can cause electric shocks and present a fire hazard. Any electrical cables, power cords or extension cords that are damaged, or are not functioning properly, should be removed from service immediately.
Regularly check cords for any sign of exterior damage including cracks, nicks, cuts, or frays. If the protective coating is damaged in any way, it`s time to replace it. If you notice damage to an extension cord, don`t try to repair it – throw it out.
Avoid Using Damaged Extension Cords

Exposed cords, frayed wires, or cracked plugs can cause an extension cord`s electrical flow to become uneven. This can cause a short circuit, which can trip the circuit breaker and potentially cause shock. Don`t risk using a damaged extension cord.

Occasional use cords are very lightweight, light gauge 16-gauge extension cords. They`re suitable for light duty indoor applications, like running holiday lights, portable fans, your electric hedge trimmers, or your vacuum cleaner.
The 16 gauge cord is the perfect weight and durability for extended use.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

The power brush floor rug attachment on my Eureka 6997 A Oxygen Canister Vacuum goes on an off as I use it. I replaced the The power cord from the handle has 2 plug in connections:
1 at the handle / upper wand
1 at the lower wand top of the power brush attachment

I replaced the entire wand assembly and it worked great for a year or so and now it’s doing the same thing again. I was told to keep the power switch on the handle set to off when connecting the power brush attachment or it will bu

ANSWER : This is from the prongs not making a good connection causing an arch inside the plugg causing what looks like rust on the plugg. I would try snugging up the connection by squeezing the female section to get a better connection on the prongs when it is plugged in together.

Replacing Power Cord to Power Nozzle
ANSWER : The height adjust mech. has 2 tabs, that you have to unlock, It also is easier when you tip the power head so as not to puit pressure on the Ht. Adj. wheels. Use a flat blade screwdriver and if you look down bertween the ht. adj. mech. and the elboe where the wire is, you should be able to see the 2 tabs, just pry it away form the elbow and it will come off. When you put it back on, make sure all wires are routed where they were and tip powerhead, it will snap into place.

Cord rewind The power cord is jammed and won’t go in or out. I can’t find a way to get the cover off to have a look at it. Any suggestions please?
Power cord jammed won’t go in or out. Can comeone tell me how to undo the casing to get to the power cord?
ANSWER : Which model do you have..

Power cord can not find replacement power cord for power brush attachment on kenmore canister vacuum, model #2491290 power brush attachment model # 5491290. i can not even find those model #’s anywhere online, not even partsdirect.com. any help would be great. thanks, david
ANSWER : Call 1-800-948-1358 ask for Buck mon.-fri. 9am-5pm est sat.9am-1pm est

Cord replacement I need to replace a damaged cord (the reel works). How do I get the top off so I can remove the back end? Once I get it off, will I be able to change the cord, or do I need to buy the whole reel assembly? (and thanks for the help – I love this site!)
ANSWER : You will probably have to replace the whole reel cord. Depending on your model, on each side, there is a bar in the middle that will slide off, then the 2 halfs will come apart. They will only slide in one direction. If an older model, there are screw on the top to remove the top panel, then remove the 2 screws on the bottom and the reel cord (which is the back end of the vac)will come off. Pay attention to where the wires go so you don’t hook them up wrong.

GE canister 106766 Power cord does not stay in bezel
ANSWER : Yes you are absolutely right.you would save on shipping cost if order both together.
.
.and for parts you can also order it from
.www.radioshack.com
.or from the source which you already have it with you.
.thanks.you are on the right track.you can continue ordering the parts.
.please do rate the solution.
.keep updated.thank you for using fixya.
.

Need to replace power cord on Hoover windtunnel need wiring help
ANSWER : Without seeing this it would be difficult to describe. I would take it to a vac shop and let him show you. there are no real schematics for the wiring of these units. I usually would cut off the cable with a few inches of insulation to know where to install the new one and reuse the old terminals if needed.

Replacing Power Cord Kenmore Progressive Upright
ANSWER : That actually sounds correct, if it’s the model I’m thinking of. As long as you’re talking about connecting to the wires that are held in by the wire nuts you should be good to go.
.
.-R