Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
Introduction. The Dyson filter is located in the ball-shaped base of the vacuum.
On most Dyson upright vacuums however, the filter is located underneath the dust cup. To access the filter in this machine, you`ll have to completely remove the dust receptacle and open the cover near the base of the sweeper. If you have a smaller machine like the Dyson ball, the filter is located inside of the ball.
It`s important to reset your filter life after you have replaced your filter. Resetting your HEPA+Carbon filter life Press and hold the Night mode button on your remote control. The display on your machine will countdown from five, the filter life will be reset and your machine is ready to use.
You can try to clean them and reuse them, even if the brand says to discard them after use, but be aware that they won`t be operating with the same thoroughness afterwards. There are a few different methods you can use to clean your HEPA filter.
Wash filters in cold water only
(don`t use detergent or wash in a dishwasher or washing machine). Rinsing under the water supply then gently squeezing the water out of the filter. Repeat until the water runs clear.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
I just received my Hepa filter in the mail today. Product #XSH621 – Hepa filter for EP619 & EP621 :005-04 When bought my vacumn, I was told that the filters were free and all I do is pay Postage. Today I received one filter and it lookes like I got charged the postage for two filters. The packages slips: One stated order #11152282 The other order # 1151940 If I get charged for two I expect to receive two. Can you help me with this matter or where can I go to get resolution. Catherine Fantini e-
ANSWER : This isn’t really a problem that can be fixed here on Fixya rather than advise you as a buyer. You’d have to contact the people/company you have purchased the filters from and take it up with them regarding the postage. Hope you get a decent reply.
Roomba keeps saying clean brushes yet are clean!
ANSWER : Make sure you take off the little cap at the end (the one that spins — just grab it and pull it straight off) and clean under it too. The rest of the brush may look perfectly clean but what happens is that hair gets stuck under spinning cap and, like a slowly growing washer, it pushes the whole brush toward the gear box. When it gets pushed over enough, the large yellow ring starts to rub against the side of the brush deck making it harder for the motor to turn the brush and you get that “remove and clean brushes” message.
I have a hoover 3000 i have not used in awhile, and since I removed a large rug, I would like to use it again on my slate floor. HOWEVER, I cannot get it to pick up ANY water in the water recovery unit……it is dry, dry, dry. I have put in a new filter, cleaned the nozzle unit, the scrubber , and reconnected both the recovery unit and the water unit several times, but to no avail. I would like to get a graut attachment a well as replacement part, but since I can’t get the basic unit to work, I
ANSWER : Have you made sure the plastic filter cover with the round hole in it that covers the filter is in place ( part # 59177096 ). This piece seems to get lost, and without it there is no pick-up. The other common problem is that the wheel assembly has been damaged. Look at the bottom of the Floormate. You will see a black plastic wheel assembly. There are two pegs at the rear attaching it to the base. If this piece has a crack in it where it attaches to the base, there will be no pick-up.
Dyson DC07 i have the dyson dc07 and i want to clean the filter but i have lost the instructions. does anyone know how to clean the filter or where i can get a copy of the user manual??
ANSWER : Http://www.analogstereo.com/dyson_vacuum_owners_manual.htm
Bissell lift off vacuum about 4yrs old. Extremely noisy. OK until before Christmas but getting worse every time it’s used. Washable filters washed, HEPA filter replaced. brush bar cleaned of every scrap, hose empty,everything that can be cleared has been. Noise high pitched, screeching and can only bear to use it for a few seconds at a time. Suction OK.
ANSWER : Sounds like a bad motor bearing. If it is, then you would have to replace it. Could be the brush roll, did you check the ends to make sure they turn easily?
Electrolux twin clean vacuum cleaner. After 5 minutes it keeps of thinking the filters need cleaning (and they don’t). I re charge the
power, and all seems fine and then it goes back to
wanting the filters cleaned. The suction is also
not working to full capacity.
ANSWER : Because the suction is not working fully it feels that the bags must be full and the air cannot be pulled through the bags. It could be due to 1) bags not being of correct quality. The air has to pass through them to allow all the dust to reach there. 2) There being real low suction due to a blockage somewhere. Check and remove he blockage.
Our Bissell Cleanview II 3576M does a great job except that the filter cup below the dirt cup gets full very fast and the dirt cup barely has anything in it. To clean the whole house, I have to empty the dirt cup and clean the filter several times. It didn’t use to work this way. It seems like something is missing, a gasket or seal maybe? I don’t think dirt, hair and debris should be going straight to the lower cup and bypassing the upper. I looked at the user guide but can’t see why it’s happen
Our problem with our Rainbow E Series is that it has sucked water up and blown it out through the lower part of the hepa filter, making the filter wet and dirty. This had happened before and the repair shop did not see any problems with the machine, so we replaced the filter and were very carful not to overfill the tank and to change the water often. Now it has happened again and ruined another filter. Do you know what could be causing this issue? Can the filter be cleaned or will a new one be
ANSWER : Thank you for allowing.us to help, please respond with further questions and concerns
..
Spanish speaking.available for all problems
..
Before you leave.feedback, ensure that your concerns and problems are addressed completely with.me.
..
PLEASE do not forget to.award/PROVIDE “POSITIVE” FEEDBACK
.
.
Hello, thank you for sharing your problem with us, I would personally be happy to provide the most accurate and up to date information for you.
.
.
1. There is no reason to waste money on an EXPENSIVE replacement. While some people may like the fact that something that may be brand new may work better, this is not always the case.
.
2. You can easily set the filter out to try as long as there is NO WET ELECTRICAL COMPONENTS, if so, you will be facing electrical damage
.
3. Once you have performed a natural or sun dry on the old filter, ensure to check your unit for anything that may have caused the back clog.
.
4. Back clogs for your model are often times associated with a BUILD UP of dirt and HAIR. YOU may always use pressure air for example at a gas station to flush out the build up.
.
5. Other occasions, users accidently build the vac WRONG causing continual backup and water going where it is NOT suppose to go.
.
6. Please visit me again if your problem persists.
.
.
.
..
Thank you for allowing.us to help, please respond with further questions and concerns
..
Spanish speaking.available for all problems
..
Before you leave.feedback, ensure that your concerns and problems are addressed completely with.me.
..
PLEASE do not forget to.award/PROVIDE “POSITIVE” FEEDBACK
