Oreck XL Ultra Bagged Upright Vacuum
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
The roller brush is the combination of a belt, a roller, and sometimes a small vacuum head motor. The roller spins, and the bristles attached to it sweep up debris that then gets sucked into the dirt container of the vacuum. The brush head also helps to pull dirt and debris out of carpets of various pile heights.
Description. Used extensively for preparing, cleaning and finishing surfaces, disc brushes can be provided in a range of materials and sizes to suit all applications. Constructed on a synthetic, wood, aluminium or steel core, tufts of fill material are machine stapled, resin set or hand drawn into the core.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
Installing roller brush for oreck XL 21 – Oreck XL Ultra Bagged Upright Vacuum
ANSWER : Uh, probably not sure what the issue is, but
.1. unplug unit.
.2. Remove the multiple screws from the bottom of the unit.
.3. remove the bottom baseplate (usually black)
.4. the brush roll is now visible, and the belt should be around it.
.5. Pull the brush roll away from the unit, and disengage the belt.
.6. Replace in the opposite order. Make sure that baseplate fits properly to insure a good seal. Also watch the bumper (rubber part that is wrapped around the unit) to make sure it is properly seated.
.7. Handroll the roller brush before plugging in. Make sure it moves freely.
.8. Run unit, may get a slight burning smell, but if this continues for more than a minute – turn off and inspect the unit. Brush roll requires a short burn in time, on initial build, factory accomplishes this during test procedures.
.1. unplug unit.
.2. Remove the multiple screws from the bottom of the unit.
.3. remove the bottom baseplate (usually black)
.4. the brush roll is now visible, and the belt should be around it.
.5. Pull the brush roll away from the unit, and disengage the belt.
.6. Replace in the opposite order. Make sure that baseplate fits properly to insure a good seal. Also watch the bumper (rubber part that is wrapped around the unit) to make sure it is properly seated.
.7. Handroll the roller brush before plugging in. Make sure it moves freely.
.8. Run unit, may get a slight burning smell, but if this continues for more than a minute – turn off and inspect the unit. Brush roll requires a short burn in time, on initial build, factory accomplishes this during test procedures.
Read Full Q/A … : Oreck XL Ultra Bagged Upright Vacuum
Electrolux Epic 6500SR Full Bag sensor working, Does not Reset properly
ANSWER : The problem was a sticking switch that was not being reset. The vacuum on/off switch mechanism is comprised of two switches. One is the main switch that turns the vacuum on and off. The second is a shut off switch that gets tripped when the full bag sensor is engaged. This second switch is supposed to get reset when you push the on/off switch on the outside of the machine. The full bag shutoff switch was stiff and it, therefore, was taking a couple of presses of the on/off switch to move the shutoff switch back into the running position.
Read Full Q/A … : Oreck XL Ultra Bagged Upright Vacuum
Dirt devil vacuum cleaner–trouble vacuuming dirt and pet hair on carpeting –is the problem with the spinning brush which contacts the floor, not contacting the carpeting?? I thought (when I bought this vacuum) that the aforementioned brush was adjustable to various heights of carpeting. Sometimes, it seems like nothing is being vacuumed up –unless I have just put a new bag on the vacuum… Do I need or can I replace the spinning brush on the bottom of the vacuum so it kicks up and vacuums
ANSWER : Try replacing the belt. Rubber belts stretch out after about a year.
Read Full Q/A … : Oreck XL Ultra Bagged Upright Vacuum
Now that I just fixed my Lux Legacy canister vacuum, I need help on my other Electrolux Regency Series upright! The vacuum works fine but the rotating brush does not work and the brush motor does not turn on. Tried cleaning the brush and hitting hte reset button to no avail. This upright has a triple setting switch and I checked the each of the wires seem to be attached. Tried rotating the brush by hand and it would not budge. Was going to “encourage” the brush to turn with a set of articula
ANSWER : There are a couple rectangular holes on the bottom of the power nozzle, beside the wheels. These have tabs in them that need released with a standard screwdriver.
.
.Once they release, turn the vacuum over and lift cover of power nozzle at the back. This pulls the front of the cover out of the lip on the “bumper”.
.Once this is done, you’ll need to unscrew the screw at each end of the brush. Lift the brush out and thoroughly clean it, including the ends.
..
.Check the wiring to make sure they’re connected to the terminals of the motor. Also, check the belt for wear and tear. These belts can last for five years or more, but if it looks bad a good time to replace it is while you have the power head apart.
.When reassembling the vacuum, ensure the belt is fitted properly around the motor shaft and brush.
.Insert the front of the cover first, ensuring the edge fits neatly beneath the lip on the bumper all the way around. It takes a little manipulating to press the back into place. Make sure both tabs click into the locked position. Turn the vacuum over and reinstall screws. Try to rotate brush by hand a few times.
.At this point, plug the vacuum in and turn it on. If the power head doesn’t run, press the reset button. If the power head motor still doesn’t run, it could be due to loose or disconnected wires that lead to the reset switch, a bad reset switch, or even a bad motor. The vacuum needs to be taken to the nearest Aerus Electrolux store for further diagnosis and repair.
.
.http://www.aerushome.com/storelocator/
.
.Once they release, turn the vacuum over and lift cover of power nozzle at the back. This pulls the front of the cover out of the lip on the “bumper”..Once this is done, you’ll need to unscrew the screw at each end of the brush. Lift the brush out and thoroughly clean it, including the ends.
.
..Check the wiring to make sure they’re connected to the terminals of the motor. Also, check the belt for wear and tear. These belts can last for five years or more, but if it looks bad a good time to replace it is while you have the power head apart.
.When reassembling the vacuum, ensure the belt is fitted properly around the motor shaft and brush.
.Insert the front of the cover first, ensuring the edge fits neatly beneath the lip on the bumper all the way around. It takes a little manipulating to press the back into place. Make sure both tabs click into the locked position. Turn the vacuum over and reinstall screws. Try to rotate brush by hand a few times.
.At this point, plug the vacuum in and turn it on. If the power head doesn’t run, press the reset button. If the power head motor still doesn’t run, it could be due to loose or disconnected wires that lead to the reset switch, a bad reset switch, or even a bad motor. The vacuum needs to be taken to the nearest Aerus Electrolux store for further diagnosis and repair.
.
.http://www.aerushome.com/storelocator/
Read Full Q/A … : Oreck XL Ultra Bagged Upright Vacuum
Electrolux vacuum brush not turning problem:
was vacuuming and rug got caught auto shut off kicked off power to brush. instead of hitting red button to restart brush I disconnected brush to vacuum some hair in Conner. after i reconnected the brush and hit the red button but no power to brush. Light won’t even switch on. Hope you can help
ANSWER : Under the vacuum, there is a guard..remove the guard , either by 2 screws or by 2 clips..there is a belt under the guard..that is connected to the brush..the belt need to be replaced.
Read Full Q/A … : Oreck XL Ultra Bagged Upright Vacuum
Unbeknownst to me, someone took the bag out of my Kenmore Progressive vacuum and failed to replace it. I have been vacuuming without a bag for months, and today the vacuum stopped sucking. When I opened up the front to replace the bag, tons of dirt and dust came pouring out. I thoroughly cleaned the vacuum, put in a new bag, but still no sucking power. Just dust coming from the rear vents where one of the filters is. Is the vacuum ruined, or is it a simple solution of buying a new filter?
ANSWER : Sounds like you need to buy a new motor. All that grit and dust will ruin a motor and I’m surprised it lasted as long as it did.
.This is where a vacuum that won’t run without a bag would have been nice. (Aerus for one)
.This is where a vacuum that won’t run without a bag would have been nice. (Aerus for one)
Read Full Q/A … : Oreck XL Ultra Bagged Upright Vacuum
Roller brush not rotating – Oreck XL Ultra Bagged Upright Vacuum
ANSWER : This may be the belt, and it may be the brush roller.
.
.I am leaning more towards the belt. The belt on any vac should be changed once a year, and for the pet lovers 2 times a year.
.
.Good luck.
.Mark
.
.I am leaning more towards the belt. The belt on any vac should be changed once a year, and for the pet lovers 2 times a year.
.
.Good luck.
.Mark
Read Full Q/A … : Oreck XL Ultra Bagged Upright Vacuum
I would really like to wash the outer bag of my vacuum, but I have a problem. I can remove the outer bag from the vacuum, but the plastic ‘frame’ that is inside the outer bag is sewn to the bag. So what am I supposed to do about that if I want to put it in the washing machine? I have the Oreck XL Silver.
ANSWER : Hi,
you can wash the bag. However you cannot wash the bag in the wash machine. What you will want to do is look for the screw or depending on the model, untwist the cap down on the rod next to the machine. that entire pole section will come off of the unit below with the bag there.
I recommend if it is warm outside to use the garden hose to spray it and scrub inside the bag with a scrub brush and some dish soap.
I usually throw them into the laundry sink and let soak, scrubbing with soap and water.
To dry the bag, a hairdryer or hang to dry before putting the piece back onto the machine.
Good luck.
Mark
Read Full Q/A … : Oreck XL Ultra Bagged Upright Vacuum
