Sebo X4 Bagged Upright Vacuum
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
If your vacuum cleaner keeps turning off, this could be due to the following reasons: Blockages – check the hose and head for any obstructions. Filter – always check your filters, if these are clogged this could be causing the vacuum cleaner to work harder and lose suction power.
Check the active wand, the flexible hose, filter bag and micro-filters, and any on-board attachments that may be clogged. Also remove the brush roller to check for blockages. Inspect the orange trap door on the underside of the power head and remove any debris or blockages.
After years of use, your brush roller may exhibit very little visible wear so gives the impression it is still fit for service. However, don`t be fooled by this (as many people are). The bristles become soft with time with the result that the machine becomes very heavy to push around when in use.
Check that the vacuum cleaner is plugged into a working power outlet and that fuses and breakers don`t need resetting. An activated thermal cut-out due to a blockage is the next most likely cause of the problem. Check for blockages in the hose and filters, and remove any obstructions that you find.
If you are lucky enough to own a SEBO vacuum, you are guaranteed a life span of at least 15 years thanks to the hard work of German engineers. Nonetheless, learning some basic maintenance tips and tricks wouldn`t hurt the longevity of your vacuum. In fact, it may lengthen the total life expectancy upwards of 20 years!
Brushes. According to iRobot, brushes should be replaced every 6-12 months. Robot vacuums like the iRobot Roomba j7+ have multiple brushes that allow it to clean.
Low suction or poor pick-up may be due to a clog in the vacuum cleaner. If you notice a change in the sound of the motor or a reduction in the spinning action, check for clogs. First, remove the Easy Empty dirt tank from the vacuum and discard all dirt and debris.
If the brush roller is obstructed, the machine will shut off and the red „CHECK BRUSH“ light located on top of the power head will flash. The user should turn the switch off, unplug the machine and immediately remove the obstruction.
You`ve changed your bag as the light told you to, and when you switch the machine on the red light is still illuminated. If that red light stays on for more than a few moments, the machine will switch itself off. It is designed to do this – that is a safety feature to protect the motor that is built into the machine.
One of the first things to do when your Dyson vacuum cleaner keeps starting and stopping is to empty the bin. It may be full, or the machine may simply perceive it as too full to continue working. Dyson vacuum cleaners require constant airflow through them to work, and a full bin can stop this from happening.
Low suction or poor pick-up may be due to a clog in the vacuum cleaner. If you notice a change in the sound of the motor or a reduction in the spinning action, check for clogs. First, remove the Easy Empty dirt tank from the vacuum and discard all dirt and debris.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
Electrolux Epic 6500SR Full Bag sensor working, Does not Reset properly
ANSWER : The problem was a sticking switch that was not being reset. The vacuum on/off switch mechanism is comprised of two switches. One is the main switch that turns the vacuum on and off. The second is a shut off switch that gets tripped when the full bag sensor is engaged. This second switch is supposed to get reset when you push the on/off switch on the outside of the machine. The full bag shutoff switch was stiff and it, therefore, was taking a couple of presses of the on/off switch to move the shutoff switch back into the running position.
It just keeps saying that my bag is full and cutting out, bag not full and have tried changing it anyway, but still cutting out
ANSWER : I would check the air filter. It sounds like it’s over heating and shutting off because it doesn’t have good airflow.
Jim
I have a new Kenmore magic bued and I am about to change bags for the first time. Trying to do this the clip that is supposed to hod the bag close to the whole keeps coming off when I replace it and close the lid, turn on the vac the sucction is very low and it keeps showing the bag is full which is not true / what is going wrong here ?
Thanks so much for supporting,
Beba
ANSWER : Sorry to hear that you are having problems with you Kenmore Magic Blue.
There is a so-called “bag full indicator”, which will only turn red if it got some major blockage. This is the reason why there is no power suction.
The “full bag sensor is just a spring mechanism that springs closed when there is a blockage. Remove the bag and look for clogs. When using it, check the bag and change it when full, not go by the “bag full indicator.”
Good luck, I hope this helps.
I was vacuuming and noticed that the bag needed changing. the red light with the ! inside the triangle also came on. When the bag was changed, the vacuum would not restart. The red light came on. Tried the reset button but nothing happened. Tried unplugging and re-plugging in and nothing happened. Replaced all the filters and still it wouldh’t start. So I brought it downstairs and tried one more time to get it to start. it worked! Is there something wrong with the vacuum cleaner? Was it overheat
ANSWER : It was overheated that is
why it worked downstairs after cooling off.
Bag full indication comes on; changed bag; still wont run.
ANSWER : Turn the knob on the top of the vacuum all the way to the right and try it again
Bag was full, changed it, the unit now turns off
ANSWER : Try dialing the control valve to the mid way position. If the unit still shuts down with the bag full light on you have a damaged control valve under the dial on the top of the vac.
This valve failure is common in this model and can only be repaired by someone with original AERUS Electrolux repair parts, generally at an AERUS repair shop.
Won’t start. My son was using the vacuum & Didn’t change the bag. The vacuum was making the full bag smell, but the light was’t on & it didn’t stop. I stopped him, changed the bag, checked the filter, closed the compartments & turned on the vacuum. Nothing happened. I checked to be sure that it was plugged in, that wasn’t the problem. I’ve let the vacuum “rest” for several days, It still won’t start. Any suggestions?
ANSWER : There is a reset button at the back of the powerhead. The user manual can be downloaded from the electrolux website, although I didn’t find it very useful. There was some info on how to change the powerhead drive belt.
I have an electrolux epic 6500 sr. The change bag light came on, I changed the bag, now it won’t run properly. If the bag is out and the hose attached it will run or if the bag is in and the hose is off it will run, but not if the bag is in and the hose is attached. Any suggestions?
ANSWER : First, if it runs without a bag, there’s a problem with the bag lock-out switch or wiring. This needs to be replaced/repaired by an authorized Aerus Electrolux technician.
.
.First, turn dial on top of vacuum counter-clockwise so the smallest dot lines up with the arrow. See if it stays on. If not, detach hose and turn vacuum on. Place palm of hand over intake. If it turns off, it’s possible that the tubes connecting to the CVA are clogged and simply need cleaned. This is most often caused by using “made to fit” Electrolux bags. Dust is sucked through the bags and into the motor compartment of the machine. All interior parts get covered in dust and need to be cleaned. If this is the cause, the vacuum is best cleaned and repaired at an authorized Aerus Electrolux store. If the vacuum shuts off, or won’t turn on before placing hand over the intake, it’s probable the control valve assembly is bad and needs replaced.
Another cause is an overheated motor due to clogged screen at back of bag well, full or clogged bag, dirty afterfilter, bad wiring/connections, clogged hose, clogged power head, or bad motor. It depends largely on the type and model of cleaner. Clogged wands are also a possibility, but unlikely.
Check and clean screen at back of bag well.
Replace bag. Make sure it’s a genuine Electrolux bag made by Home Solutions.
Check and replace afterfilter if necessary. These should be replaced after every six bags.
Broken and worn wiring connections are often found in the hose ends due to abuse and normal wear and tear. You can check the continuity of the hose using a continuity tester or multi-tester. If a multi-tester, turn dial to one of the Ohm settings. Place one probe into one of the terminals on the end of the hose. This will be referred to as T1. Touch the other probe to each of the terminals/connections on the other end of the hose. These will be T3 and T4. One of them should read zero, the other should read infinity. Repeat this with the other terminal, which will be T2.
Drop a marble in one end of hose and let it roll through. If it doesn’t roll through, the hose is clogged and needs to be cleared. Plug hose into the exhaust port of the vacuum, place other end in the in port. Turn vacuum on. This provides a blowing and sucking action which should clear the hose.
Detach hose from power nozzle (PN). Drop a marble into the wand end of PN. If it rolls through, it’s clear. If not, there’s probably a clog behind the brush where the intake opening is. You may be able to reach this through wand end with needle nose pliers, or either end with a knitting/crochet needle or a bent coat hanger.
If none of these “fixes” provide the answer to the problem, it should be taken to the nearest Aerus Electrolux store for diagnosis. Repairs or checks involving disassembly of the vacuum should always be done by an authorized Aerus Electrolux service technician.
The store nearest you can be found by following the instructions at the below listed link:
http://www.aerushome.com/storelocator/
