iRobot Roomba 530 Robotic Vacuum

How to Identify and Fix Common Vacuum Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :

If there is a clicking sound when you rotate the side brushes manually (with the side brushes on). It indicates that the noise is from the side brush motor. Replacing the side brush motor could fix the issue.
Grinding noises are often caused by bits of debris getting lodged behind the brushes or into the cleaning head, especially large bits like dry pet food. This will clatter around or jam the brushes to create the noise you`re hearing. A thorough cleaning should put everything right.
Error 2 means the rubber brushes in your Roomba are clogged and need to be cleaned.
Replace the battery

If your Roomba is making noise while charging, it could be because of the battery. The rechargeable batteries in all Roombas are designed to last for about two years and will need to replace if you don`t want your device to start making noises and stop working properly.

Most owners believe that running their robot vacuums four times per week is sufficient to keep the floors dust-free. However, if you have children or pets, you should use your robot vacuum more frequently. Daily vacuuming is recommended if you suffer from seasonal allergies.
On average, a well-maintained robotic vacuum cleaner can last up to 4-6 years, but some models may last even longer.
Robot vacuums can range anywhere from 50 to 80 decibels. (For reference, 80 decibels is equivalent to the volume of city traffic while inside a car.) Our quietest pick, the Eufy RoboVac X8 Hybrid, measured as low as 60 decibels during our testing, which is about the volume of a normal conversation between two people.
1 beep: Roomba is stuck with a wheel hanging down or Roomba is stuck. 2 Beeps: Roomba`s main brushes cannot turn. 5 Beeps: Roomba`s side wheel is stuck. 6 Beeps: Roomba`s cliff sensors are dirty or Roomba is stuck hanging over a cliff or on a dark surface.
iRobot Roomba vacuums can operate even with simple ambient light, but not in total darkness. What may help with either the i7 or s9 robots is to run a training mission and/or clean your floors with the closet light on until your floor plan map is complete.
With proper care, your robot`s battery should last at least 2-3 years before it needs to be replaced.
You can easily check the status of the battery in the iRobot® HOME App. A battery icon will be displayed in the top-right corner, indicating the current status of the battery.
“The beauty of iRobot Genius is that our robots get smarter over time and continuously provide customers with new ways to clean where, when and how they want,” said Keith Hartsfield , chief product officer at iRobot.
Based on current reviews, our test data shows bots usually perform very well on hard floors (with no models scoring less than 77% in this aspect of the test), but can really struggle with carpet, corners and pet hair.
A traditional, standard vacuum uses around 1.4kWh of power per hour; the humble robot charges on about 60-90 watts (over three hours), with one charge fuelling roughly an hour of cleaning. It`s a no brainer! However, it`s just not as simple as all that.
Applicable for those products

In this way, the vacuum can always be ready and cleaned on schedule daily. If you are leaving for a long time, like one week, it`s recommended to unplug the adapter and the charging base/auto-empty station and turn off the main power switch of your RoboVac for safety.

The side brush replacement procedure will be the same for all series. Loosen the side brush screw with a screwdriver or coin. Remove the side brush. Install the replacement side brush by firmly pressing it onto the side brush post.
The Roomba® s Series Dual Multi-Surface Rubber Brushes – now 30% wider* clean large areas efficiently and work together to help get floors thoroughly clean. One brush loosens and agitates dirt, and the other moves in the opposite direction to extract and pull it in. Compatible with Roomba s Series Robot Vacuums Only.
Filters tend to last 3-4 months, rollers generally 9 months or so in average homes.
The good news is that adding this detailed mapping is easy — your robot does all the work. When you first get a Roomba, it will automatically start learning your home`s layout.
They are also equipped with powerful suction that can effectively remove dirt, debris, and even bugs. By regularly vacuuming with a robot vacuum, homeowners can significantly reduce the number of bugs in their homes.
A smart robot vacuum can be used to spot and clean specific areas of your home, like entrances, dead corners underneath the sofa and bed, or even dining tables.
Roomba® can also learn your home as it cleans. It typically takes three (3) to five (5) cleaning missions or Mapping Runs to generate a fully developed Imprint™ Smart Map that you can then customize and use.
A: Yes, I do. My Roomba 780 runs at it`s schedule time, 10am, then sometimes, I`ll run it again in the evening if I have a particular area that needs to be done (I do my master suite, guest suites & upstairs each separately).
Besides regularly cleaning the brushes on your Roomba, you`ll also need to replace them from time to time. iRobot recommends replacing the two main brushes every six to twelve months.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Roomba keeps saying clean brushes yet are clean!
ANSWER : Make sure you take off the little cap at the end (the one that spins — just grab it and pull it straight off) and clean under it too. The rest of the brush may look perfectly clean but what happens is that hair gets stuck under spinning cap and, like a slowly growing washer, it pushes the whole brush toward the gear box. When it gets pushed over enough, the large yellow ring starts to rub against the side of the brush deck making it harder for the motor to turn the brush and you get that “remove and clean brushes” message.

It says to clean brushes and they are clean and it keeps making a clicking sound. Only 4 months old.
ANSWER : You need to remove the brush tray and clean all the parts behind the brush housing.

Roomba keeps saying clean brushes yet are clean!
ANSWER : Remove the Yellow connectors on the end of the brushes and clean around the pin well. If there is too much there, the roomba thinks there is something stuck and goes into clear mode (as if there is a chord stuck).

Brushes only work when Dust Bin is removed!!
I have cleaned & cleaned this thing! It runs for about 2 mins & stops, says “Clean Brushes”! and now it’s very noticeable it’s not picking up well… but is picking up a bit. I take the dust bin out, and the brushes spin…. and it has much more power…. and is very clear it is working! But it’s useless without the dust bin! LOL It’s only 9 months old…. called customer service, but it was the one time it worked just fine! Of course, I thought I’
ANSWER : HI,
If the brushes work , without the bin, the problem , the problem could be caused , due the failure at the bin lock mechanism. There is a sensor that checks if the BIN is connected properly or not. This problem is best resolved by getting the same replaced .

Thanks for using Fixya
Proton

I have cleaned & cleaned this thing! It runs for about 2 mins & stops, says “Clean Brushes”! and now it’s very noticeable it’s not picking up well… but is picking up a bit. I take the dust bin out, and the brushes spin…. and it has much more power…. and is very clear it is working! But it’s useless without the dust bin! LOL

It’s only 9 months old…. called customer service, but it was the one time it worked just fine! Of course, I thought I’d stop here first before calling again! Than

ANSWER : Ok, this is a “Brush Height Adjustment” issue. It will probably work great on a hard surface but on carpet the brushes bog. If you’ve taken the unit apart already…Sorry….do it again. When you do, you’ll see a String which allows the brushes to “Float” on different surface heights. Loosen the screw a little and pull a bit more string through. Re Tighten the screw and put it together enough for a test run. Now reset the roomba.To reset the Roomba, power the Roomba on, and press the Spot, and Dock.buttons together for at least 8 seconds. Until it plays a tune. The.clock, and any schedule is erased at this time. Try running the Roomba.with the dust bin removed to see the brushes spin easier..
.
Second method, is taking off the bottom cover, and removing the.battery. While it’s removed, and not plugged into the charger, press.the clean button for at least 20 seconds. This will erase the memory..Replace battery, and cover. Run the Roomba to see if the brushes start.to spin. You can also remove the brush housing by removing the 4 screws.and reseating it, to see if it was a bad connection, since you have the.bottom cover off.

My Irobot Roomba keeps saying that I need to clean Roombas brushes. I have cleaned the brushes…they are spotless. Still the Roomba will go for 2 minutes and shut itself off stating once again to clean the brushes. What up?
ANSWER : Perform the troubleshooting found at the iRobot website: http://tinyurl.com/nh5c8a (I promise that really does go to the right site.) That troubleshooting will enable you to determine exactly what’s causing this problem. (The Easy Way: Run the Roomba minus the dustbin and look in the back. Is the brush turning? If not, there’s the problem. Give support a call at 1-877-855-8593 and they’ll let you know how to replace the necessary part.)

Roomba Discovery My Roomba turns on and moves but the brushes won’t turn. Someone told me that I had forgotten to put in the yellow and black end bearings, but I did. Help, I miss my Roomba
I have a Roomba 530, I have had it for 2 weeks and really loved it. I have followed all the cleaning instructions etc.. Then the Roomba wanted it’s brushes cleaning “please clean Roombas brushes” So thinking that something was stuck I removed and cleaned the brushes, (yellow tabs on and in place by the way)
ANSWER : I read somewhere that you need to clear the software in case there is a glitch. To do this, take the battery out and then, simultaneously hold down the “spot” and “clean” buttons for 30 seconds. Replace battery. This has worked for my Discovery model.

My Dyson DC 14 is making the horrible “ratcheting”sound only when the brush is engaged on the carpet setting. I have cleaned the brush, so there are no obstructions, the canister is empty and properly on the unit. I checked to make sure all of the “traps” and hoses are clear of obstructions, the belt is on the brush securely and moves freely, the brush itself spins freely, but there is still the “ratcheting” noise. Any other suggestions?
ANSWER : Our DC33 was making the same ratcheting sound immediately upon placing the cleaner/brush head on the carpet. We carefully pulled the beater/brush bar out of the vacuum. Once removed, we pulled the black plastic end off of the center rod. We discovered hair wrapped around each end of the center rod. After the hair was removed and the clean/brush bar was re-installed, the vacuum ran flawlessly. Hope it works as well for you as it did for us.