Vacuums\015 My Kenmore Upright with bag 12 amp model 116 32212200 worked perfectly until the upright handle fell backwards and hit the floor when I was using the hose attachments. This has happened many times in the past. This time the vacuum died and will not turn on. I had an identical model that did the same thing several years ago, found this one in Goodwill and it worked perfectly until this morning. Is there a hidden power reset switch or main circuit breaker / fuse that causes this to happen?\015
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
Check service panel for tripped breakers/blown fuses. If breaker is tripped, reset it. If fuse is blown, replace it. If vacuum cleaner is plugged in, be sure power button is in the off position before resetting breaker/changing fuse.
Loose connections will cause your vacuum cleaner to lose suction. Make sure that the dust container, the hose, the tube and the brush are all attached properly. If the problem continues, your vacuum cleaner might have a technical problem. If you suspect this to be the case, contact an authorised service agent.
The most common reason for vacuum motors failing is overheating. Most `dry` vacuums have a flow-though motor. These motors use the air they have sucked up the dust with, to cool themselves. When there is a blockage, flow-though motors are unable to cool themselves due to the lack of airflow.
The most common problems found in vacuum cleaners are low suction force, excessive noise, burning smell, vacuum not turn on, and overheating. These issues can be fixed by either cleaning the device or replacing some parts of the device. At times, it is best to seek a professional to fix the cleaner effectively.
Overheated Motor
If your vacuum was working fine and then suddenly shut off, it may have overheated. Most vacuums are equipped with a thermal protector safety switch that won`t allow the motor to run when it becomes overheated. You will need to wait for 30 minutes to 2 hours, depending on your machine, to try again.
Putting in the incorrect amount of oil, putting in the wrong type of oil, and oil contamination can all cause the pump to not reach full vacuum. For this reason, you must check the oil regularly to ensure that it is not only clean, but also properly filled.
Start the engine and spray
Scope out all the vacuum lines under the hood. Then start the engine and spray each connection with a light stream of water. If a connection sucks in the water, you`ve found your leak. A vacuum leak can cause a rough idle, high rpm, poor gas mileage and even trigger a check-engine light.
A damaged vacuum hose, clogged motor air filter or bad suction motor can cause the vacuum cleaner to shut off during use. A tripped overload on the vacuum suction motor can shut off the vacuum cleaner during use. If your vacuum has a reset button, push it; if the vacuum seems hot, let it cool off first.
What is a Good Suction Power for a Vacuum Cleaner? An upright cordless vacuum cleaner should have at least 100 air watts to effectively clean a variety of floor surfaces, with the best Samsung vacuum cleaner reaching up to 210W*.
The basic formula F=PxA is used to calculate the force of the suction cup with: F is holding force (or the vacuum force of the suction cup) P is pressure. A is is the contact area (the size of the suction cup surface)
The most common problem with a vacuum cleaner is also the easiest to remedy: clogs in the hose or attachments. Also the electrical cord, motor, switch, fan, brushes, and motor bearings can all need repair or replacement.
The average life expectancy of a mid-range vacuum cleaner is about six years. You can fix or replace things like blocked filters, jammed brush rolls, frayed hoses, worn-out stick vac batteries and broken accessories yourself.
– Some vacuums have an in-line thermal fuse (often located between the switch lead and the motor coil). If the fuse is blown it will need to be replaced. – Check your home circuit breaker – it may have tripped. – Some vacuums have a brushroll on/off control.
Typically, a vacuum leak will cause situations like hard starting, rough idle, excessive fuel consumption, and engine codes. You might even be able to hear a leak – sometimes a whooshing or whistling sound can be heard with the engine running.
This overload reset switch button (part number 8191505) is for vacuums. Overload reset switch button 8191505 resets the overload switch when you push it. Unplug the vacuum before installing this part. Wear work gloves to protect your hands.
One of the most accurate methods of vacuum leak detection is the helium leak detector. A sensor is usually placed near the inlet to the vacuum pump to detect any increase in helium concentration in the air stream. Helium is then sprayed on any potential leak points in the system or piping.
If your Shark ION Robot R75 vacuum stops moving unexpectedly after a few minutes of normal movement, it may simply have low battery power. Check that the device is powered on and that the battery has a significant charge.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
The original belt on my upright Kenmore Progressive broke and I replaced it with the spare that was in the vacuum. The vacuum and spare belt are about 10 years old. Then the spare broke after one vacuuming session and there was a burning smell coming from the vacuum. I ordered new belts and replaced it with the new belt. It seems to be working fine with no smell. I checked the belt after I vacuumed the family room and although it was in tact, the belt was very hot. Is that normal? Should t
ANSWER : The belt heats up due to the friction, as well as being in contact with the shaft of a hot motor. It is normal.
Read Full Q/A … : Vacuums
I purchased a brand new Eureka Pet vacuum, sorry don’t know exact name but it the one that has the self cleaning duster on it. Last night I used the vacuum on my carpet, it was working fine until I accidently sucked up the corner of a scarf that was hanging off a couch. I shut the vacuum off, pulled out the scarf and and resumed vacuuming. Much to my dismay the suction on the vacuum had ceased. Can you tell me if there is a reset button on the vacuum? The vacuum does not appear to be damage
ANSWER : If the motor is running, there should be suction. Possible problems depend on whether it’s a canister or upright and are:
.A clog in the hose, UR or canister. Detach hose. Drop small coin in one end and lift hose causing it to roll out the other. If it does, no clog in hose. Drop same coin into hose opening on power head. If it rolls out, no clog in PN.
.Broken fan blades, UR. Needs to be taken to shop for repair/replacement.
.
.A reset button is for use if the motor isn’t running, so won’t have anything to do with the suction.
.A clog in the hose, UR or canister. Detach hose. Drop small coin in one end and lift hose causing it to roll out the other. If it does, no clog in hose. Drop same coin into hose opening on power head. If it rolls out, no clog in PN.
.Broken fan blades, UR. Needs to be taken to shop for repair/replacement.
.
.A reset button is for use if the motor isn’t running, so won’t have anything to do with the suction.
Read Full Q/A … : Vacuums
Unbeknownst to me, someone took the bag out of my Kenmore Progressive vacuum and failed to replace it. I have been vacuuming without a bag for months, and today the vacuum stopped sucking. When I opened up the front to replace the bag, tons of dirt and dust came pouring out. I thoroughly cleaned the vacuum, put in a new bag, but still no sucking power. Just dust coming from the rear vents where one of the filters is. Is the vacuum ruined, or is it a simple solution of buying a new filter?
ANSWER : Sounds like you need to buy a new motor. All that grit and dust will ruin a motor and I’m surprised it lasted as long as it did.
.This is where a vacuum that won’t run without a bag would have been nice. (Aerus for one)
.This is where a vacuum that won’t run without a bag would have been nice. (Aerus for one)
Read Full Q/A … : Vacuums
Dirt devil vacuum cleaner–trouble vacuuming dirt and pet hair on carpeting –is the problem with the spinning brush which contacts the floor, not contacting the carpeting?? I thought (when I bought this vacuum) that the aforementioned brush was adjustable to various heights of carpeting. Sometimes, it seems like nothing is being vacuumed up –unless I have just put a new bag on the vacuum… Do I need or can I replace the spinning brush on the bottom of the vacuum so it kicks up and vacuums
ANSWER : Try replacing the belt. Rubber belts stretch out after about a year.
Read Full Q/A … : Vacuums
My home has a central vacuum system hook-up but no vacuum installed. My friend upgraded his central system and gave me his Eureka Mega Boss central vacuum system and the accessories, including the pow
ANSWER : The power head requires 120 Volts. Some hoses have a receptacle in the handle for the power head plug, and the hose has a cord at the wall inlet end that plugs into a receptacle. Some hoses have a plug at the wall inlet end that plugs into a 120Volt receptacle built into the inlet. The hose plugs into this receptacle when you push the hose into the inlet. The power for this built-in receptacle is wired with line voltage when the system is installed.
Read Full Q/A … : Vacuums
I have a Kirby G4 Vacuum Cleaner – MOdel G4 D. I have never had any problems or repairs done to it in the past ten plus years that I’ve had it. This is an upright vacuum. I was vacuuming the carpet floor and was not having any trouble at all. I switched the vacuum off and moved it into a different room. When I tried to turn on the vacuum, it would not turn on. I checked with different outlets, used both front attachment and hose attachment. Checked the front part of the motor/ spiral case. This
ANSWER : Hello,
.My educated guess is that it’s either the switch or the power cord. Here are a couple of guides to help with diagnosis and repair…
.
.http://reviews.ebay.com/COMMON-PROBLEMS-WITH-THE-KIRBY-VACUUM-TROUBLESHOOTING_W0QQugidZ10000000003800312
.
.http://reviews.ebay.com/REPLACING-THE-POWER-SWITCH-ON-ANY-KIRBY-G-SERIES-VACUUM_W0QQugidZ10000000003752018
.
.Hope this helps!!
.Marci
.My educated guess is that it’s either the switch or the power cord. Here are a couple of guides to help with diagnosis and repair…
.
.http://reviews.ebay.com/COMMON-PROBLEMS-WITH-THE-KIRBY-VACUUM-TROUBLESHOOTING_W0QQugidZ10000000003800312
.
.http://reviews.ebay.com/REPLACING-THE-POWER-SWITCH-ON-ANY-KIRBY-G-SERIES-VACUUM_W0QQugidZ10000000003752018
.
.Hope this helps!!
.Marci
Read Full Q/A … : Vacuums
Power cord can not find replacement power cord for power brush attachment on kenmore canister vacuum, model #2491290 power brush attachment model # 5491290. i can not even find those model #’s anywhere online, not even partsdirect.com. any help would be great. thanks, david
ANSWER : Call 1-800-948-1358 ask for Buck mon.-fri. 9am-5pm est sat.9am-1pm est
Read Full Q/A … : Vacuums
I have a tank style vacuum. When I vacuum with the power head it dims and slows down when I push the power head back and forth, but it powers back up louder when I stop pushing it If i remove the powerhead from the hose the vacuum works fine.
ANSWER : Most likely the belt. Thats the cheapest so try it first
Read Full Q/A … : Vacuums
