Kirby G4 Bagged Upright Vacuum\015 .Kirby Lexan Fan .is broken and i need help to figure how to get at the fan so i can replace it the part cost $14 does anybody have any suggestions or web pages to help me with this problem .Thank you very much anyone for your help\015
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
Manufacturing Date: 1993 – 1997
– The Kirby G4 model featured a brand new 3-position handle locking mechanism as well as other improvements that made it easier to maneuver and function! It also included optional accessories and attachments to enhance the cleaning power and versatility of this specific model!
Factors may include having a bad motor, incompatible pump applications or poor ventilation. Constant overheating may indicate a malfunction.
Kirby vacuum cleaners are made of die cast aluminum where most other vacuums are made of plastic. This makes the Kirby vacuum more durable than other model on the market. This is why the average lifespan of a Kirby is over 30 years.
Kirby vacuum prices are higher than many vacuums found at big-box stores, but that`s because Kirby vacuums are made of durable materials that will last for years. Why replace an inexpensive vacuum over and over again when you can purchase a Kirby vacuum? This complete home cleaning system that will last for a lifetime.
The Kirby is built in America by employees dedicated to their craft.
If too much hair, string, or lint is caught in the brushroll, the brushroll can get stuck. If the brushroll is stuck, it will put too much strain on the belt and may cause the belt to break. Remove the brushroll and clean out any debris from the bearings. After replacing the brushroll, make sure that it turns freely.
If you`re smelling rubber, the belt has either burned out and snapped or the belt has become so stretched out that the roller is not moving and the vacuum belt is getting super heated from the motors RPM.
Q: It smells like the belt is burning. What is wrong? A:It is likely the belt isn`t turning freely on the brush roll. Flip out the belt lifter handle and turn it clockwise until the green arrows line up.
Check that the vacuum cleaner is plugged into a working power outlet and that fuses and breakers don`t need resetting. An activated thermal cut-out due to a blockage is the next most likely cause of the problem. Check for blockages in the hose and filters, and remove any obstructions that you find.
Vacuum cleaners are fairly simple machines. They need power to be transmitted to the vacuum to create a suction force that lifts debris. So, the usual areas that cause suction loss include the wrong height setting, stuck rollers, a faulty gasket, a broken vacuum belt, a filled bag, or a clogged hose.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
Kirby Lexan Fan is crack and need help to replace
ANSWER : Hello…
.Check out my online instructions…
.
.http://reviews.ebay.com/KIRBY-VACUUM-REPAIR-HOW-TO-REPLACE-THE-FAN-IMPELLER_W0QQugidZ10000000003711302
.
.Hope they help!
.Marci
.Check out my online instructions…
.
.http://reviews.ebay.com/KIRBY-VACUUM-REPAIR-HOW-TO-REPLACE-THE-FAN-IMPELLER_W0QQugidZ10000000003711302
.
.Hope they help!
.Marci
Read Full Q/A … : Kirby G4 Bagged Upright Vacuum
Kirby Vacuum Hi Bruce, In my opinion, yes the Kirby would be worth it, as long as you are not replacing the motor. The switch would be the most expensive part besides the motor that would need to be replaced. The switch costs USD 49.99, the cord is roughly $39.99, and the carbon brushes are $29.99. I can easily walk you through any of these repairs should you need help. Kirby’s are great vacuum cleaners, that usually last 30+ years. Brand new these machines sell in the US for $1600 or more,
ANSWER : You can get better prices from Goodvac.com
Read Full Q/A … : Kirby G4 Bagged Upright Vacuum
My older Dyson DC14 (the purple one) early model with a clutch on the beater bar belt needs a clutch replacement. The bar has been cleaned and there are no worn or damaged parts so I conclude that the clutch at the motor end of the belt needs to be replaced. I can find the part online but no instructions on how to disassemble the vacuum to get to and replace it. Dysons only advice is to give me the address and phone of the nearest service center. Can you help me?
ANSWER : Have a look at www.dysonmedic.com which has some very useful info on dismantling and repairing Dysons.
.
.Although this site doesnt actually cover the DC14 yet, the DC14 is very similar to the DC07 so as regards dissassembling the machine, and replacing the clutch, my experience is that the DC07 info will enable you to do the job.
.
.Although this site doesnt actually cover the DC14 yet, the DC14 is very similar to the DC07 so as regards dissassembling the machine, and replacing the clutch, my experience is that the DC07 info will enable you to do the job.
Read Full Q/A … : Kirby G4 Bagged Upright Vacuum
KIRBY G4 FAN ASSEMBLY ORDER
ANSWER : First put the gasket on the spacer, thin end to to out, push it down all the way on the motor shaft, then put the nylon washer on, then the fan, metal washer and then the pulley, just snug it, (don’t tighten too much just beyond hand tightening). Put the casing, top and handle back on.
Read Full Q/A … : Kirby G4 Bagged Upright Vacuum
I need to replace the fan and am not sure Kirby G 4 A
ANSWER : Greetings from GoVacuum,
.
.We’ve shot a video showing you detailed instructions on how to replace the fan on a Kirby Generation vacuum cleaner. The video is in two parts below. If this video was helpful to you, please be sure to rate this Solution by clicking the four Thumbs Up icons in the top right hand corner of this Solution;
.
.Changing the Fan On a Kirby Generation Video, Part 1:
..Kirby Fan Change Video Part 2;
.
.
.
.
.We’ve shot a video showing you detailed instructions on how to replace the fan on a Kirby Generation vacuum cleaner. The video is in two parts below. If this video was helpful to you, please be sure to rate this Solution by clicking the four Thumbs Up icons in the top right hand corner of this Solution;
.
.Changing the Fan On a Kirby Generation Video, Part 1:
..Kirby Fan Change Video Part 2;
.
.
.
.
.Thanks,
.
.Chris Jones
.GoVacuum.com
Read Full Q/A … : Kirby G4 Bagged Upright Vacuum
Need to replace the suction hose, need help reattaching
ANSWER : You need to purchase a new hose – you can search for it online (DC07 External hose) or you can simply call the Dyson helpline and order it through them.
Read Full Q/A … : Kirby G4 Bagged Upright Vacuum
My wall ceiling fan’s control unit UC 9051T failed. Light switch button does not work. If I replace it with some generic universal unit, do I need to replace transducer located in the fan housing also, or all of them are compatible? Thanks in advance. M
ANSWER : First, you didn’t say you checked that the bulb worked. Is that burned out?
.
.If bulb is ok, you will have to make sure the switch is matched with the fan (ususally a set of 4, 6 or 8 micro-switches have to be set the same in both switch and fan to be on same frequency of communication – even if you have an exact US 9051T controller).
.
.A whole new fan is not too expensive ($100) and may be best route if you use the fan alot and it is over 7 years old – just an option.
.
.Also, just because the light doen’t work doesn’t mean it is the switch transmitter that is broken, it could also be the receiver. Call the company on the website below – they will either tell you how to check or you can send everything to them and they will check for you.
.
.http://www.eceilingfans.com/
.
.Sorry for making it so difficult – I hope it is just your bulb.
.
.-Mark
.
.If bulb is ok, you will have to make sure the switch is matched with the fan (ususally a set of 4, 6 or 8 micro-switches have to be set the same in both switch and fan to be on same frequency of communication – even if you have an exact US 9051T controller).
.
.A whole new fan is not too expensive ($100) and may be best route if you use the fan alot and it is over 7 years old – just an option.
.
.Also, just because the light doen’t work doesn’t mean it is the switch transmitter that is broken, it could also be the receiver. Call the company on the website below – they will either tell you how to check or you can send everything to them and they will check for you.
.
.http://www.eceilingfans.com/
.
.Sorry for making it so difficult – I hope it is just your bulb.
.
.-Mark
Read Full Q/A … : Kirby G4 Bagged Upright Vacuum
How do I replace the drive belt on a kirby G4? Actually the belt is already replaced I just need to know how to reattach that front part back onto the main vacuum. HELP
ANSWER : Greetings from GoVacuum,
.
.Here’s a video we shot showing you in detail how to install a belt properly, and how to reattach the head properly. I hope this helps you;
.
.
.
.Here’s a video we shot showing you in detail how to install a belt properly, and how to reattach the head properly. I hope this helps you;
.
.
Read Full Q/A … : Kirby G4 Bagged Upright Vacuum
