Hoover SteamVac F5914-900 SpinScrub Upright Vacuum\015 Can someone give me a web site to print the owners manual for Hoover steamVac upright\015

How to Identify and Fix Common Vacuum Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :

Should the brush not rotate freely there may be debris tangled around the ends of the brush, carefully remove any obstructions or replace the brush with a new one. We recommend that you fit a new belt and brush once per year to keep your Reactive vacuum working efficiently.
A: Yes, you can just rinse your carpet with plain water when using the Hoover SmartWash Automatic Carpet Cleaner. Helpful?
To make a spray that will clean just about anything—countertops, the sink, light fixtures, and more—mix 13 ounces of hot water, ½ cup of white vinegar, 15 drops of grapefruit essential oil, 10 drops of lavender essential oil, and seven drops of lemon essential oil in a spray bottle, says Kimberly Button, a certified …
The key to cleaning your carpet efficiently is to work in straight, consistent lines. Squeeze the trigger on your carpet cleaner to release the water, and push forward a few feet. Then release the trigger, and pull back over the same line.
While carpet cleaners are designed to work optimally with carpet shampoos, they will also do the job with a laundry detergent. In fact, this is one of the safest substitutes you can use. Using laundry detergent in a carpet cleaner will provide you with effective results and you won`t even have to use a lot of it.
FAST DRY TIME: Tackle surface stains as they happen with Quick Clean Mode and enjoy dry carpets in 45 minutes.
Use the dust brush attachment – close the blind slats so they lie flat and vacuum. Reverse the blinds so that the slats are lying the other way and repeat. Repeat monthly or as needed. Use the upholstery attachment on mattresses and fabric surfaces.
The level you set your vacuum depends on the height of your carpet. For bare floors, use the lowest or bare floor setting, for short and medium pile carpets use a medium setting and finally, for plush carpets use the highest setting.
I boil the water and pour it in carefully—boiling hot. Most home cleaners do not use the power of boiling water, but I do. I have done this for 14 years now, and without any problem.
Clean your steam cleaner with water and empty it. Pour some water and add laundry detergent to it. Mix it well. Power on it and use it similarly to the way you use vacuum cleaners.
If the product is not making steam please check that there is water in the tank fitted at the top. If the product is not making steam please check that there is water in the tank fitted at the top. Pull the tank up and fill it up with water. Please do not add any cleaning solutions to the water in the tank.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Parts replacement We have a Hoover Steam Vac that has a broken part #10 in your picture or Part # 37271035. Does this part cover the whole top section of the Vac? Is it hard to replace? Where can you get the best prices on Hoover parts? I have been on Hoovers website and they don’t even recognize this Steam Vac. which is hard to believe they don’t even recognize their own unit? Thanks Ray
ANSWER : This the hood or top cover. There some screws on the bottom as well as on the top, then it comes off.

My Hoover steam vac spin scrub model 4060-900 brushes are not spinning and I have lost the manual. Any ideas. Thanks. [email protected]
ANSWER : The problem I found with one a neighbor was tossing out is the bearings in the part that drives the brushes were stuck. Lubing them up solved the problem, but took a bit of work to get into. This also provides a good chance to clean the crud out of bits that usually don’t get much attention. I found mine clogged with a fair amount of pet hair.

You’ll need a Phillips & Flat Screwdriver, some light machine (3-in-1) oil or Lithium (white) grease, and a lot of patience. Having a pan or something handy to keep all the little bits organized would help.

First remove both the soap & recovery tanks, they’ll just get in the way & are designed to be easily removed & replaced for filing/dumping. Be sure to fold the “wings” for the recovery tank in or they’ll foul removing the cover later (as will the brush speed button).

The tricky part is getting the Brush Speed knob off. It’s held on only by friction, but can be tough to pull for without breaking the plastic stick it’s pushed onto.

Remove the brushes. There are 4 blocks between the outer & next in rollers. Put the flat screwdriver between the gray & clear plastic, pushing gently toward the brushes. This pushes a wedge away far enough from a hole in the gray plastic to “unhook” the brush housing from the main body. Once all 4 are clear, the brush assembly should pull out easily.

Remove the 2 big screws in front of the brushes and the one at the back of.the clear plastic front of the vacuum bit. The small ones at the extreme front corners hold on the clear plastic front, and can be removed if you want to clean out the vacuum channel, but are not necessary to remove to remove the top.

Toward the back sides of the top are 2 slots that hold this part on. Once the front screws are removed & the front is loose, push the side in gently & you should be able to lift the back of the cover. Push in lift both side, the top should pop right off.

Now I have the top off, holding 2 black & 1 silver long screw. In the center-front of the new-exposed guts is a box with a round top & a cone at the front with 2 screws.

This is the Brush Motor Assembly, and it’s actually vacuum-powered. Remove the 2 screws holding down the from, then look for 2 large holes on the bottom of the unit behind the black “squirter bar”.

There’s very long screws at the bottom of these holes that also hold down the brush motor.Once the 2 bottoms screws have been fully loosened & the top-front screws removed, the brush motor should pull up easily.

On the right is a square port, in front the the brush speed stick (where the gray button pops onto). on the left is a gray & black hose, these should pull off easily, but may have some liquid in them.

Pull out the brush motor & set it on a convenient spill-resistant work surface upside-down. You should see the square-hole drice for the brushes, a gray piece of plastic, & a cresent-shaped hole.

The port at the front & hole on bottom provide an air path for the vacuum to poll air through this assembly & spin the brushes. You should see 2 screws at the back of the motor & 2 more at the bottom of holes surrounded by the gray plastic. Remove all 4 screws.

You can now pull off the bottom cover with the gray plastic. Front to back you should see the brush drive gear, an intermidiate gear, ant one of the bearings for the fan that drives the whole thing. pulling out the bearing & gears to clean out this area & lube up the gears with some Lithium Grease helps, as well as making sure the bearing is well lubed with 3-in-1 oil and/or lithium grease.

The top is held on at this point with 4 platic clips. The top doesn’t need to be removed unless you *really* have to see the fan. The clips can be broken off if one is not careful, and there’s nothing in there to be lubed. Best to leave it as-is.

At the top of the driveshaft is a second sealed bearing. I couldn’t figure out how to get it out without braking it, lube this one in place. The bearings are supposed to be sealed, so removing the black “washer” from the bearing is done completely at your own risk. I just put some oil on there, spun it to work it in, then repeated with the white grease.

Replace the intermediate gear, the brush drive gear, then the lower sealed bearing in that order. You can spin the gears to ensure they’re spinning well. Mine was OK, but after a bit of use worked the grease in & the brushes really started spinning.

Keep in mind everything here except the screws is plastic, be creful to get a snug fit with the screws without overtightening. “Gorilla-ing” the screws will just break the plastic & make the whole adventure an exercise in frustration.

Reattach the bottom plate with all 4 screws, 2 in the holes in the gray plastic, 2 in the back.

Reattach the gray & balck hoses to the left side of the brush drive. They’re 2 different sizes, so there’s only 1 place the smaller hose will fit easily. Place the assembly back in the machine & replace the 2 screws in the front.

Flip the machine up so you can put the 2 really long screws back into the underside of the brush drive. There’s 2 guide slots on either side, make sure the brush with the indicator wheel on top goes into the big hole on the right. You may need to spin the brushes a bit to get the center squure stick to line up with the hole in the drive gear. The brushes should pop back in easily if everything’s lined up right.

Put the top cover on, making sure the Brush Speed stick & center screwhole line up, as well as the back sides snap into place.

Screw down the top, then flip the unit up so you can snap the bottom-front of the top over the gray wedges on the front, then screw into place.

Replace the Recovery Tank, fill & replace the solution tank, and test-drive.

Vanger Chevane.

Lost Manual for Hoover Steam Vac Model #5906-900
ANSWER : Visit www.hoover.co.uk
There you can pick after sales service,instruction manuals, etc. etc.
You will find your manual there.
I hope this helps

Beater brushes not turning on the wife’s Hoover Steam Vac model F5905-900. Found one prior ”solution” stating that it sounded like the belt was bad. That was my original thought, but on checking schematics and trying to find part numbers at Sears Parts Direct and at Hoover, it does not appear the F5905-900 steam vac HAS any belts to begin with. What’s next??
ANSWER : This one I can tell you about from personal experience with that generation Hoover Steam Vac. After using it about 7 or 8 times my brushes stopped turning also.

I disassembled it (kind of like disassembling a Chinese puzzle box) and found that the Turbine which develops the torque for the brushes simply has worn out. I replaced the part and it works fine now. Unfortunately unless you are familiar with that sort of repair it’s high on the difficulty side. When I took it to a local shop they wanted about $150 to repair it. That was more than half the price I paid for it. It’s simply not a very good design. Hoover wont’ talk about them yet they are still selling them.

The least expensive place to purchase a replacement part is at: http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=250648382497&rvr_id=&crlp=1_263602_263622&UA=%3F*F%3F&GUID=70355e091290a0aad3175ab7ff9f985a&itemid=250648382497&ff4=263602_263622.

The repair shop wanted to charge me $60 for the part.

It seems that the manufacturer is ignoring the problem and it’s a great claim for a class action suit against them.

Regards
Zashiban

I don’t know how to use my hoover steam vac on carpets, hard wood floor, my (tile floor), my upholstery. I’m spraying and yet I don’t see no suctions on neither of them. do you have a how to do step by step video that I can use in order to get the maximum result from my hoover steam vac.
ANSWER : Here is a link to the User Manual, in case that will hekp:
.
.http://www.hoover.com/pdfs/manuals/F5914900.pdf

Need manual for Hoover steam vac. F5910-900
ANSWER : For an appliance or any kind of electronic,
I would try http://userguides.50webs.com/

Need the manual for the F5918900 Hoover Steam Vac. Please tell me where I can print the Manual. I am in great need, I have lost the original. Your help is appreciated. Thanks
ANSWER : Go to Costco.com, they have the owners manual link on the description page….

Hoover u5781-900, motor shuts off (intermittent)when you shake vac or make jerky movements.If you move vac to up right position the vac starts right up.When you giggle vac, motor starts and stops no mater if you just started up or vac for ran for 45 min. Thanks Lucy C.
ANSWER : Lucy
.you have a bad connection somewhere in the unit
.this is a fire hazard and you should not use this until its been fixed
.could be a pinched wire or broken connections