Kirby Ultimate G Bagged Upright Vacuum
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
Blockage – when a vacuum cleaner becomes unusually loud, it is normally because of a blockage of some sort. This is a problem that is easily solved by turning off the cleaner, check for blockages in the pipes, and remove them. You can also check and empty the canister to remove any possible blockages there as well.
If the cleaner becomes noisy or starts vibrating, it may be because some debris has got tangled around the brush roll or agitator situated in the bottom of the cleaner.
Check the nozzle, the front end of the vacuum. If the nozzle is blocked, the vacuum will be loud or noisy while cleaning.
Kirby vacuum cleaners are made of die cast aluminum where most other vacuums are made of plastic. This makes the Kirby vacuum more durable than other model on the market. This is why the average lifespan of a Kirby is over 30 years.
This means it is best to choose a vacuum cleaner with a noise output that is less than 70 dB. However, the noise levels of vacuum cleaners fall between 75dB to 85dB. Thus, continuous exposure to such noise levels affect a user`s health while also being a sign and source of inefficiencies in the equipment.
Sound enclosures, noise reduction blankets, sound curtain noise barriers, or sound barrier walls are a few options to consider when reviewing noise reduction materials. If the vacuum pump is indoors, a noise enclosure would be the recommended solution.
If your machine is making an abnormally loud noise it is likely due to the belt slipping or the brush roll being incorrectly installed, follow these steps to resolve: Turn off and unplug machine. Use a Phllips-head screwdriver to remove 3 screws, 2 in the belt cover and 1 on the brush roll mount. Remove belt cover.
If all you hear from the vacuum unit is a click at the when you try to start the vacuum motor from inside the house, then the motor in the unit is dead and has to be replaced. A strong odor from the shellac, which coats the copper coil windings, is an indicator that the motor is about to or has burnt out.
When your vacuum pump exhibits loud or atypical noise, then it may be close to failure. Throughout their use, ageing and accumulated wear cause a specific part in the pump to fail. Increased noise is often a sign that a pump requires maintenance and cleaning.
Second, can you vacuum too much? Believe it or not the answer is no. Now, if you vacuumed continually 24 hours a day, yes, that would be too much. Vacuuming every day, or even a few times a day, is not going to create any long term problems.
Sound enclosures, noise reduction blankets, sound curtain noise barriers, or sound barrier walls are a few options to consider when reviewing noise reduction materials. If the vacuum pump is indoors, a noise enclosure would be the recommended solution.
What should I do? If your vacuum cleaner whistles, this is usually a sign that your device can`t suck in sufficient air. Often, it`s the dust container or bag that`s full. Check these first and exchange them if necessary.
What should I do? If your vacuum cleaner whistles, this is usually a sign that your device can`t suck in sufficient air. Often, it`s the dust container or bag that`s full. Check these first and exchange them if necessary.
The majority of robot vacuums produce noise at a level between 70 and 80 dB, comparable to that of a garbage disposal or a noisy restaurant.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
Loud Noise My Kirby vacuum makes a very loud noise when it is turned on. It still works and picks up trash, but the noise is new.
ANSWER : I believe you will find the answer you seek by clicking on this link.
.
.http://reviews.ebay.com/COMMON-PROBLEMS-WITH-THE-KIRBY-VACUUM-TROUBLESHOOTING_W0QQugidZ10000000003800312
.
.Hope it helps…
.Marci
.
.http://reviews.ebay.com/COMMON-PROBLEMS-WITH-THE-KIRBY-VACUUM-TROUBLESHOOTING_W0QQugidZ10000000003800312
.
.Hope it helps…
.Marci
Read Full Q/A … : Kirby Ultimate G Bagged Upright Vacuum
Infinity Vaccum by Shark, model number NV31COS, will not start. The vacuum was running just fine until it grabbed the edge of a curtain. Turned it off to release the suction. Turned it back on and was working fine. About a minute later the vacuum was making an odd noise. Every 2 seconds or so it would “heave” (lack of a better word) then go away, then come back and so on. Turned the vacuum off and checked for blockage, none that could be seen or felt, and now the vacuum won’t turn. Any suggestio
ANSWER : Carpet brush won’t turn when vac on
Read Full Q/A … : Kirby Ultimate G Bagged Upright Vacuum
Hi folks,
my beam vacuum makes a very loud roaring noise quite often.
the problem started when i was vacuuming up a quantity of vermiculite from my chimney.
i think i overloaded the vacuum i think and it made this loud roaring noise.
the vacuum tends to make thos noise when i am hoovering after 5 minutes or so.
any ideas?.
thanks in advance Tom….
my beam vacuum makes a very loud roaring noise quite often.
the problem started when i was vacuuming up a quantity of vermiculite from my chimney.
i think i overloaded the vacuum i think and it made this loud roaring noise.
the vacuum tends to make thos noise when i am hoovering after 5 minutes or so.
any ideas?.
thanks in advance Tom….
ANSWER : If the filter bag is bad and didn’t trap all of the dust, then it got into your motor, so you may have a problem with your motor now.
Read Full Q/A … : Kirby Ultimate G Bagged Upright Vacuum
Electrolux Epic 6500SR Full Bag sensor working, Does not Reset properly
ANSWER : The problem was a sticking switch that was not being reset. The vacuum on/off switch mechanism is comprised of two switches. One is the main switch that turns the vacuum on and off. The second is a shut off switch that gets tripped when the full bag sensor is engaged. This second switch is supposed to get reset when you push the on/off switch on the outside of the machine. The full bag shutoff switch was stiff and it, therefore, was taking a couple of presses of the on/off switch to move the shutoff switch back into the running position.
Read Full Q/A … : Kirby Ultimate G Bagged Upright Vacuum
Rainbow Vacuum, about 5 yrs old (bought new, no issues prior) – my 6yr old tipped it on it’s side while water was in basin. Now when I turn the power on, it makes a very loud sound in the motor and you can feel the vibration on the floor. The suction still works and basin still catches dirt – the noise is just so loud and I’m not sure if I should continue use or how to fix -?
ANSWER : Although a wet/dry vacuum, it cannot tolerate water in the motor. Water will cause the motor to short out, which will cause the motor to act/sound like yours does now, if it continues working at all.
.To prevent additional problems, the vacuum needs to be taken to an authorized Rexair dealer for cleaning and repair. Expect at the very least to pay for a new motor and installation.
.Problems like this are why I don’t care for any wet/dry vacuums, especially spendy ones.
.Oh, you should definitely discontinue use, and don’t attempt repairs on your own. Special tools are needed, and if bolts and screw are rusted, breakage may result.
.To prevent additional problems, the vacuum needs to be taken to an authorized Rexair dealer for cleaning and repair. Expect at the very least to pay for a new motor and installation.
.Problems like this are why I don’t care for any wet/dry vacuums, especially spendy ones.
.Oh, you should definitely discontinue use, and don’t attempt repairs on your own. Special tools are needed, and if bolts and screw are rusted, breakage may result.
Read Full Q/A … : Kirby Ultimate G Bagged Upright Vacuum
I replaced the belt on my Dirt Devil Featherlite Bagless Vacuum and the brush roller rubs and makes a very loud noise when turned on. I have gone exactly by the manual instructions and made sure the belt and end caps were on correctly, but the bristles still rub the back and it makes a very loud noise. Without the brush roller in the vacuum, it sounds and runs normal. What could the problem be?
ANSWER : Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=561283
.Generic problem for all Vacuums
.I replaced the belt on
.Posted by piggytail on May 01, 2008
.I replaced the belt on my Dirt Devil Featherlite Bagless Vacuum and the brush roller rubs and makes a very loud noise when turned on. I have gone exactly by the manual instructions and made sure the belt and end caps were on correctly, but the bristles still rub the back and it makes a very loud noise. Without the brush roller in the vacuum, it sounds and runs normal. What could the problem be?
.
.Hello,
.I would advise you to ALWAYS to FIRST UNPLUG YOUR VACUUM before beginning any service procedure.
.The Royal Dirt Devil Featherlite Bagless Vacuum has just bushings in the ends of the brushroll and not bearings and once the bushings are bad I suggest that you replace the brushroll in the vacuum and put a new belt on the vacuum as well. There is no way to repair the bushing s in order to it to work properly. The suggested belt change is every 4 to 6 months and to store the extra belts in a Ziploc bag in the refrigerator to keep them fresh. Suggest looking at a local vac dealer. So if you need further assistance, please feel free to contact your local vacuum cleaner dealer in your area or in the yellow pages, or contact the factory phone number or website to further assist you with your questions.
.http://www.royalvacuums.com
.Customer Service
.For help with a model that is not working, if you want to check an order, if you need help finding a part or service center or have any other comment, complaint or question that is not a technical question about this web site use the link above. You can also call our Customer Service department between 8AM and 7PM EST Monday through Friday at (800) 321-1134.
.www.A-1Vacuum.com 1-800-657-1874 If you cannot find a local dealer near you they can ship you the parts UPS.
.Don – The Vac Man
.Go Ahead. Use Us.
.
.Generic problem for all Vacuums
.I replaced the belt on
.Posted by piggytail on May 01, 2008
.I replaced the belt on my Dirt Devil Featherlite Bagless Vacuum and the brush roller rubs and makes a very loud noise when turned on. I have gone exactly by the manual instructions and made sure the belt and end caps were on correctly, but the bristles still rub the back and it makes a very loud noise. Without the brush roller in the vacuum, it sounds and runs normal. What could the problem be?
.
.Hello,
.I would advise you to ALWAYS to FIRST UNPLUG YOUR VACUUM before beginning any service procedure.
.The Royal Dirt Devil Featherlite Bagless Vacuum has just bushings in the ends of the brushroll and not bearings and once the bushings are bad I suggest that you replace the brushroll in the vacuum and put a new belt on the vacuum as well. There is no way to repair the bushing s in order to it to work properly. The suggested belt change is every 4 to 6 months and to store the extra belts in a Ziploc bag in the refrigerator to keep them fresh. Suggest looking at a local vac dealer. So if you need further assistance, please feel free to contact your local vacuum cleaner dealer in your area or in the yellow pages, or contact the factory phone number or website to further assist you with your questions.
.http://www.royalvacuums.com
.Customer Service
.For help with a model that is not working, if you want to check an order, if you need help finding a part or service center or have any other comment, complaint or question that is not a technical question about this web site use the link above. You can also call our Customer Service department between 8AM and 7PM EST Monday through Friday at (800) 321-1134.
.www.A-1Vacuum.com 1-800-657-1874 If you cannot find a local dealer near you they can ship you the parts UPS.
.Don – The Vac Man
.Go Ahead. Use Us.
.
Read Full Q/A … : Kirby Ultimate G Bagged Upright Vacuum
Terrible noise My dyson was working great then started making this horrible noise. I cleaned the bar but noise is still there. I discovered the beater bar went around three passes then froze and started horrible noise again. my husband got the bar turning but after 2 swipes vacuuming it did it again. Can it be fixed or is it time to retire it and buy a new one. Wendy Kiser
ANSWER : That noise is the clutch. A very expensive part and very hard to replace. When a problem with the clutch happens it’s generally not worth the time and money to replace.
I suggest getting a different type of vacuum, maybe a Miele or Sebo. With the money spent on one of those vacuums, you wont have problems like you would with a Dyson. And the cleaning power is so much more powerful than what any Dyson can offer.
Read Full Q/A … : Kirby Ultimate G Bagged Upright Vacuum
I have the eureka capture vacuum and it works great; however, it has recently started making an extremely high pitched sound when I use it. It is still vacuuming but the noise is so loud it hurts my head and I can only vacuum for a few minutes at a time before I have to turn it off. What is wrong with it???
ANSWER : Dust is getting past the dust cup filter, to the motor. Call Eureka customer service. 1-800-282-2886.
Read Full Q/A … : Kirby Ultimate G Bagged Upright Vacuum
