Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
Your Vax carpet cleaner may not be picking up water because the machine has picked up too much grime, and has become blocked up. Check around the head of the carpet cleaner for anything obvious that might make the suction on the Vax weaker, or look for clumps of hair that could be caught in the bristles.
Clog located in the vacuum hose
Turn the unit on and feel the suction at the end of the hose handle. If there is no or low suction, then the clog is in the hose. You can remove the clog by running a long, stiff object through the hose, such as a butter knife, starting at the wall end.
Hold the end of the hose below the water level in the tank to prime. With a full tank of water and the Machine off and reclined press the clean shot button `on` Wait for the clean shot to run for a few seconds, this will reprime your machine.
Hold the end of the hose below the water level in the tank to prime. With a full tank of water and the Machine off and reclined press the clean shot button `on` Wait for the clean shot to run for a few seconds, this will reprime your machine.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
I do not have my users manual and have never vacuumed wet with this vacuum. How do I change it from a dry to wet vacuum.
Can’t find my manual and I need to use the shop vac for water in basement, do I have to change the filter or what
lost my user manual never used it to pick up water. need to know how to puit it in wet mode i want to clean the dirty water out of my pool.
Can’t find my manual and I need to use the shop vac for water in basement, do I have to change the filter or what
lost my user manual never used it to pick up water. need to know how to puit it in wet mode i want to clean the dirty water out of my pool.
ANSWER : .Vacuuming Liquids
.1. When picking up small amounts of liquid
.the filter may be left in place.
.2. When picking up large amounts of liquid
.we recommend that the filter be
.removed. If the filter is not removed, it
.will become saturated and misting
.may appear in the exhaust.
.3. After using the vac to pick up liquids,
.the filter must be dried to reduce the
.risk of possible mildew and damage to
.the filter.
.4. When the liquid in the drum reaches a
.predetermined level, the float mechanism
.will rise automatically to cut off
.airflow. When this happens, turn off
.the vac, unplug the power cord, and
.empty the drum. You will know that the
.float has risen because vac airflow
.ceases and the motor noise will
.become higher in pitch, due to
.increased motor speed.
.IMPORTANT: To reduce the risk of damage
.to the vac do not run motor with float
.in raised position
.1. When picking up small amounts of liquid
.the filter may be left in place.
.2. When picking up large amounts of liquid
.we recommend that the filter be
.removed. If the filter is not removed, it
.will become saturated and misting
.may appear in the exhaust.
.3. After using the vac to pick up liquids,
.the filter must be dried to reduce the
.risk of possible mildew and damage to
.the filter.
.4. When the liquid in the drum reaches a
.predetermined level, the float mechanism
.will rise automatically to cut off
.airflow. When this happens, turn off
.the vac, unplug the power cord, and
.empty the drum. You will know that the
.float has risen because vac airflow
.ceases and the motor noise will
.become higher in pitch, due to
.increased motor speed.
.IMPORTANT: To reduce the risk of damage
.to the vac do not run motor with float
.in raised position
Read Full Q/A … : Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum
The Hoover Steamvac Widepath will NOT pick up water. The dispenser with cleaner DOES have water. The TANK that would receive the dirty water is NOT full. All tanks are on properly and the machine will still not pick up the used water. I found a tear in the interior hose leading to the receiving tank and repaired throughly with electrical tape. Still will not pick up the water. Any suggestions?
ANSWER : Sounds like a clogged air path (no vacuum action) from the floor pick-up to the collection tank. Take the tanks off and deal with the vacuum problem alone. The collection tank should have a air exit vent–is it clear? Check the interior hose that you repaired–is it clogged? Remove the bottom plate and inspect the air path from it. Because this machine deals with water, clogs can become like concrete! Hope this helps!
Read Full Q/A … : Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum
No Water My Bissell rug shampooer does not eject water or saop whan I pull the saop trigger on the handle. I checked both filters and they are clean. Then, I removed the container that sucks up the water and pulled the saop trigger, water barely came out of the tubes. I tried to clean the rug in our family room and the rug was not wet when I finished, no water coming out to clean the rug. HELP HELP HELP!!! I live in Colorado is there a Bissell repair shop near Denver, HELP!!! Thanks Dominick ema
ANSWER : Does water squirt out of the hose nozzle, if it does, then check the heater inside the handle asm. Make sure that where the tubes hook up to it are not clogged. If water doesn’t squirt, check for the seal at the bottom of the tank, it needs to be on the tank, not in the hole, this is for the soap bottle also, there is a seal on the bottom of it as well. The flow indictor cap is leaking air or maybe is too tight. If you had the top cover off, make sure that the tubes are routed right so as not to get pinched when the cover is put back on, the smart mix knob should be in the water setting and that the piston is on the bottom of the smart mix knob. Pump is bad. Try running a mix of vinegar and water to see if that unclogs the lines. Is the top cover and the base tight together in the back, sometimes the top breaks loose and it will raise up and it can’t spray, just re-fasten it down.
.
.Bissel’s Number is: 1-800-237-7691, they can tell you were to get service in your area.
.
.Bissel’s Number is: 1-800-237-7691, they can tell you were to get service in your area.
Read Full Q/A … : Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum
I have the Bissell Proheat (7901) It will pick up water and the hand tool works fine. I noticed that the red indicator stopped spinning. Then I noticed no water was coming out. If I put down water using the hand tool, the vacunme will pick it up. When I called Bissell they had me do something with the indicator. When it didn’t work they said take it in for repair.
ANSWER : Hi,
Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.
Bissell Proheat Upright Wet/Dry Vacuum Problems
heatman101
Read Full Q/A … : Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum
We have a Bissell Proheat 2X (model 8920). The problem we are having is when water/soap is initially released (all settings) it continues to leak out the front water spray nozzles unit the water containers are empty. The vacuum works but can’t keep up with the continuous water leaking out. Do you have any idea what is sticking open to allow the continued release of water when the machine is running? Thanks Rick
ANSWER : Return it. It is faulty and should not do that. Mine does not. Does require changing water about evrery 10 minutes but one can see the filth in the water. Also re-clean with plain water over areas that were cleaned to remove all cleaner. Old cleaner in carpet to dirt is like a bug attracted to a bug zapper. It can be time consuming, but it will pay for itself and can do a great job if you pay attention when water or cleaner runs out, otherwise it will not clean properly!
Read Full Q/A … : Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum
I have a 5.5 hp craftsman 20 litre wet Dry vacum . I have lost the manual. & have 2 questions 1) how do I change to wet vacum from dry? Also could i use the wet mode with some water in it and let it run while I am sanding dry wall to catch the dust in the water in the container? Thanks
ANSWER : # 1 myou just take the bag out make sure ytou sponge filter is in place athe top and turn it on the power switch just turns on ,machine ther is no wet dry switch just an empty bagless cannister is all you need make sure the ball outlet in vacumn is working it stops water from overfilling cannister # 2 just use the proper bag and attachment to vacumn up the drywall dust a good building supply store has special sanding attachments for vacumn so you can sand and vacumn at the same time
Read Full Q/A … : Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum
ProHeat Turbo Deep Cleaner Upright Steam Vacuum: Hello, My Bissell Proheat is not spraying water, …
ANSWER : Most likely the pump belt is worn and needs to be replaced. Here is the belt you need:
Read Full Q/A … : Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum
9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum: I have a Bissell proheat 2x deepcleaner 9200 model…
ANSWER : Hi,
Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.
Bissell Proheat Upright Wet/Dry Vacuum Problems
heatman101.
.
.fkj
Read Full Q/A … : Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum
