Dyson DC17 Animal Bagless Upright Cyclonic Vacuum\015 Too often my DC17 suction hose doesn’t ****. The beater bar unit always works but when in the upright position sometimes the suction hose will work but many times it won’t. Sometimes there will be suction for a few minutes and then it slowly fades until there is no suction for the hose. Thoughts?\015

How to Identify and Fix Common Vacuum Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :

Unplug the vacuum and use the Dyson Ball Animal Hose Replacement Guide to remove the vacuum`s hose and check for clogs at the base of the hose. Next, check the hose itself. Feel along-side the hose to check for a blockage. If a blockage is present, use a tool to pull out the blockage.
Check for a plugged hose:

Plugged vacuum hoses are sometimes the reason for a loss in suction. Hoses can get clogged with hair, dust bunnies, string, or anything else that can`t pass through the other end of the hose. Airways inside the machine should be looked at as well. Wherever there is an air passage, check it.

Loss of suction in your DC25, like most other Dysons, is usually caused by one of four things: Blocked or damaged filters. Splits or tears in your hosing and seals. Blockages in your ducting or.
If the vacuum`s filter is full of debris, the vacuum may lose suction, causing the device to turn off automatically. Remove the filter by pulling out the purple knob labeled “filter” located at the top of the bin. Rinse the filter by running it underwater for 2 minutes.
It may be full, or the machine may simply perceive it as too full to continue working. Dyson vacuum cleaners require constant airflow through them to work, and a full bin can stop this from happening. Make sure there`s no dirt lodged in the top part of the bin.
Clog located in the vacuum hose

Turn the unit on and feel the suction at the end of the hose handle. If there is no or low suction, then the clog is in the hose. You can remove the clog by running a long, stiff object through the hose, such as a butter knife, starting at the wall end.

If your dyson vacuum isn`t turning on, don`t panic – there are a couple possible causes. It could simply be that the vacuum overheated and shut itself off. If that is the case, wait 24 hours and turn it back on. However, another problem with dysons are failed power switches.
To add any Dyson attachment to your hose, simply slide the opening over the end of the wand. Rotate the attachment as needed to adhere it to the end of the wand. You will not hear a click or anything since the attachment relies on the tension between the 2 openings to stay in place.
A Dyson vacuum cleaner has a lifespan of around 10 years. This is considerably longer than most other vacuums. So, if you`re looking for a high-quality vacuum cleaner that will last you for a long time, a Dyson could be a good choice. However, remember that Dyson vacuums are expensive.
The suction control slider is located at the front of the cleaner head. The ball located between the bin and the cleaner head.
Putting in the incorrect amount of oil, putting in the wrong type of oil, and oil contamination can all cause the pump to not reach full vacuum. For this reason, you must check the oil regularly to ensure that it is not only clean, but also properly filled.
Low compression, an intake leak or tight valves also can cause low vacuum at idle. If the vacuum reading fluctuates within the normal range-the gauge needle bounces around a lot-uneven compression (broken rings or leaking valves or head gasket in one or two cylinders) is a likely culprit.
Check the LED light to determine the battery level. A solid blue light indicates that the machine is in normal operating mode. A flashing blue light indicates that there is no power, and the battery needs to be charged for a minimum of 3.5 hours.
A Dyson handheld that keeps cutting out is known as pulsing. A Dyson V7 pulsing problem can be very frustrating! A few reasons why your Dyson is pulsing are potential blockages or problems with the bin or filter.
Generally, the vacuum hoses on your vehicle are made from rubber and are supposed to last for a lifetime. The rough conditions that exist under the hood of your vehicle usually lead to these rubber hoses becoming damaged over time.
The hard suction hose works to draft water from below the pump, which prevents collapsing under vacuum conditions. The soft sleeve hose transfers water between the fire engine and the water source; whether it be a hydrant, tanker, another engine, or a body of water.
North American Polyester Soft Suction Hose is used to transfer water from hydrant to pumper. MADE IN THE USA AND FULLY NFPA 1961 COMPLIANT. FEATURES OF NORTH AMERICAN POLYESTER SOFT SUCTION HOSE.
If there is a strong burning smell coming from the motor area of your Dyson DC14 or DC07 then it is most likely that your motor has burnt out.
Remove the hose and check there is no blockage in the pipe. Hint: If there is suction from the hose but not the main base, there may be a blockage in the base connecting tube or the beater bar may not be rotating. Inspect the base of the vacuum cleaner for blockages and ensure that the belts are not broken.
The Dyson DC17 is an upright cleaner launched in October 2006 in the US. Although visually similar to the DC14, it contains new technologies. The first upgrade is the use of Dyson`s Level 3 Root Cyclone. This system incorporates 11 cyclones to more efficiently filter sand and dust particles out of the airstream.
A clog is a common (perhaps the most common) reason that a Dyson unit loses suction. They have a number of choke points in the airflow paths. Some considerations follow: Hoses: because of their often rough inner surfaces and inevitable bends, hoses are prime locations for clogs.
Gravity and friction are the two main forces that make vacuum suction work. While gravity pulls molecules in the air toward the earth, creating an atmospheric pressure, the suction cup and vacuum pump cause a pressure difference, attaching both surfaces.
All vacuum cleaners operate based on air flowing from the opening at the cleaning head or tool, through the vacuum cleaner and the bag and/or filter system and then out the exhaust port. This airflow is created by the vacuum motor, which also may be referred to as the suction motor.
The two main indicators to determine vacuum power performance are water lift and airflow. The water lift is measured in mmH2O, mbar or kPa. It represents the suction force and is the reference parameter for vacuuming liquids and heavy materials. The airflow is measured in m3/h or in l/s.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

My DC17 suction hose doesn’t have any suction occasionally.
ANSWER : Check the seal on the filter is not broken,And check for any blockage at the bottom of the pickup pipe.

Read Full Q/A … : Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My Eureka/The Boss doesn’t seem to have the suction power it had. However, when I place my hand under the hose, it has good suction, then when I try to pull in a small particle, it doesn’t, unless I have the hose nozzle completely over the particle. The vac is 10 yrs. old. I cleaned everything. Someone said the belt. Would the belt matter if the hose doesn’t **** well? It is just old and worn out? It did shut off recently do to overheating. Help. Thanks. Lorraine
ANSWER : Doesn’t “The Boss” Vacuum have a filter? Perhaps your filter is clogged and not allowing it to work properly.

Read Full Q/A … : Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

No suction Hello – any help with this would be much appreciated!

I just changed the bag and filters. The machine runs, seems normal, but there is no suction. There is no blockage of the hose, as indicated by the fact that that little viewer window above where the hose connects to the unit is not showing the red portion that it shows when there is something blocking the hose (god, this is hard to describe!).

If I disconnect the hose and put my hand over the hole, I feel some suction. But

ANSWER : Well, it actually sounds like there is a blockage. Try removing your hose and dropping something through it, like a quqrter. If it comes through, no clog. If it is clogged, I believe that machine has a blower on the upper part of the cleaner (maybe in the bag compartment towards the top. You can take out the filter holder and plug the hose in there and run the unit . Does the blockage come out? If not, Try shaking the hose, or you can put a stiff wire in it to try to free it. Do not run water through it. If there is no blockage at all, then you will probably need to take it to a service center. But I am pretty confident that we are looking at a clog situation. Let me know if this fixesya! Thanks, Rene (vacuum Doctor)

Read Full Q/A … : Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

No Suction I get great suction in the hose, but when I plug the hose back into the unit, there is no suction and the air flow indicator line goes completely red. I've changed the bag and filters. I took the small panel off the back and made sure there is no clog, and took the hose off to make sure there was no clog there. Still no suction. Please help.
ANSWER : I about to say that’s always a clog of some sort that causes that

Read Full Q/A … : Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have a DC07 and the brush wasn’t rotating and I had no suction at the brush but perfect suction through the hose. I noticed a large build up of dog hair around the brush so I took off the cover plate and removed all the hair, cleaned inside the floor/brush housing and cleaned out the hose. I also cleaned the filter and removed the other air access cover and made sure that they were clear. I put everything back and the brush still doesn’t turn and there is still no suction through the bottom
ANSWER : Hi and welcome to FixYa. I am Kelly.
.
.Here is a link that can assist you in your quest for the missing suction:
.
.http://www.ehow.com/how_4779428_troubleshoot-dyson-vacuum.html
.
.Also Dyson has very good info on cleaning here:
.
.http://www.dyson.com/support/help.asp?article=38&product=DC07-SY-HEPA_US
. (you have to keep clicking next…)
.
.When you get to the part where it asks “is brush head turning?” that you say No. The site is a bit lethargic but should help you get going properly again
.
.Hopefully you find “Airway inspection” as part of your on-line step by step troubleshooting.
.
.If you still have the problem after following the steps above reply / post here and we can proceed from there.
.
. Kelly
.
.
.
.

Read Full Q/A … : Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Lost suction my DCO7 lost suction in the hose I started taking it apart and cleaning it and looking for clogs (probably more than I should have) and when I put it back together it has awesome suction in the hose but no suction in the base. It just pulls the pine needles up (christmas tree) but they never appear in the “bag” compartment and when I look they are just all gathered in a clump in the bottom by the brush.
ANSWER : Hi.
.
.Remove the sole plate turn the 3 plastic screws to unlock & lift off.
.
.Now remove the blockages that have accumilated from the oppening of short clear hose.
.Check you can turn brush roller & check belt.
.
.Now reassemble switch on pull handle back & look under machine is brush spinning ?
.
.If not check the knob on side of machine is in drive (D) position.
.
.http://dysonmanuals.llc.nu
.
.Chris..

Read Full Q/A … : Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Hose Problem The hose broke just above the cuff on the inlet end of the hose.  I found that the hose doesn’t thread into this cuff but appears to be heat bonded in some way. Can I get a replacement cuff or do I have to replace the hose?
ANSWER : Looks like you can just get the hose, part #38479-4, It should just screw into the adapter or it may be glued in.

Read Full Q/A … : Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I’m trying to figure out which dyson vacuum is better, the DC14 or DC17. from what i read, the DC17 is the newer model of the DC14, the DC17 added an extra motor for the brush, but from the dyson site, the DC17 has less suction power. it went from 250AW (dc14) to 220AW (dc17). is that a significant difference that i should be worried about?
ANSWER : Hi,

DC17 is much better than DC14. I always believe User’s review are much better than what Features Company usually Displays.

Read :-

http://www.epinions.com/review/Dyson_DC17_Animal_Vacuum/content_404790546052

4 Star by 161 People is a Remarkable Achievement.

Let me know, if needed further assistance.

Hope i helped you.

Thanks for using ‘ Fixya ‘ and have a nice day!!

Read Full Q/A … : Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Hi, my name is Mea Archer, owner of the vacuum cleaner blog, the niche website that I have developed to provide the most up-to-date news, reviews and the latest advice and information for all things vacuum cleaner related.