Dirt Devil CE6000 Featherlite Wet/Dry Vacuum
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
1. The dirt canister may need emptied or the bag/filter may need to be replaced – follow the instructions in your Owner`s Manual based on your power unit type. 2. The hose may be clogged.
The most common cause of loss of suction is that the filters have become blocked. They may require cleaning or replacing. Another cause could be that the vacuum cleaner hose is blocked.
One of the easiest ways to increase vacuum cleaner suction is to empty the dust bag or container. Dust containers need to have enough space for airflow, otherwise, they could get clogged and have less suction power. Regularly check your dust compartment and empty or change it when it`s already 70-80% full.
The suction power is to be measured at the end of the tube of a complete vacuum cleaner (i.e. with tube, hose and filters – but without nozzle). Some manufacturers show the results from measurements made at the suction of the actual vacuum cleaner.
Clog located in the vacuum hose
Turn the unit on and feel the suction at the end of the hose handle. If there is no or low suction, then the clog is in the hose. You can remove the clog by running a long, stiff object through the hose, such as a butter knife, starting at the wall end.
Replace filter every 3 to 6 months.
A possible cause might be that the tank is not properly seated. To assure the tank is seated properly, pick it up and re-seat is so it sits snugly on the unit. If this doesn`t fix the problem, make sure the tank is assembled properly. To make sure they are both latched properly, pick the tank up by its handle.
Suction is the air pressure differential between areas. Removing air from a space results in a pressure differential. Suction pressure is therefore limited by external air pressure. Even a perfect vacuum cannot suck with more pressure than is available in the surrounding environment.
All vacuum cleaners operate based on air flowing from the opening at the cleaning head or tool, through the vacuum cleaner and the bag and/or filter system and then out the exhaust port. This airflow is created by the vacuum motor, which also may be referred to as the suction motor.
Suction pressure should be kept at less than 200 mmHg in adults. It should be set at 80 mmHg to 120 mmHg in neonates. [3] The catheter size used for suction should be less than 50% of the internal diameter of the endotracheal tube.
The two main indicators to determine vacuum power performance are water lift and airflow. The water lift is measured in mmH2O, mbar or kPa. It represents the suction force and is the reference parameter for vacuuming liquids and heavy materials. The airflow is measured in m3/h or in l/s.
How Portable Suction Machines Work. Portable suction machines generate negative pressure, which is channeled through a special type of plastic connecting tube called a single-use catheter. The negative pressure creates a vacuum effect that pulls any blood, mucus, or similar secretions out of the throat.
– Some vacuums have an in-line thermal fuse (often located between the switch lead and the motor coil). If the fuse is blown it will need to be replaced. – Check your home circuit breaker – it may have tripped. – Some vacuums have a brushroll on/off control.
Loose connections will cause your vacuum cleaner to lose suction. Make sure that the dust container, the hose, the tube and the brush are all attached properly. If the problem continues, your vacuum cleaner might have a technical problem. If you suspect this to be the case, contact an authorised service agent.
If there is a clog in the vacuum, you won`t have good suction and the vacuum won`t work. The clog can be in the vacuum head, the hose or where the hose meets the actual vacuum.
Again, due to the small particle size of baking soda or freshener product, these can clog the pores of your vacuum`s bag or HEPA filter. Or it can “cement” debris into the cyclones of your bagless vac! This can drastically reduce suction resulting in poor cleaning performance and cause clogs to form.
Rinse the filter
Any fine dust remaining in the filter can usually be removed with a gentle rinse under a cold tap – hold the filter under the running water until the water runs clear. You shouldn`t need to use any detergent – just water.
Airflow Issues
If the device is clogged, or the dirt cup is full, this may cause the unit to overheat. Unplug the unit and allow it cool, empty the dirt cup and clean the filter.
If the filter isn`t clean, it can impact the performance of the vacuum. Dirty vacuum filters can restrict airflow so the suction won`t be as strong.
A good rule of thumb is to replace the main filter every 3 to 5 years or when you see vacuum performance drop to an unacceptable level.
Dirt Devil is here for you to get rid all of your dirt and dog hair before your friends get to the door. The brand has introduced numerous technologies and features to its products, such as cyclonic filtration, HEPA filters, and powerful motors.
Your dirty water tank may not be secured tightly. Check the rubber tab on the dirty water tank and press firmly on all edges to secure it tightly. The accessory hose door also needs to be closed securely. Check the door and make sure it is locked in place.
Most carpet cleaning pros say they use a range of 100-400 psi for regular carpeting, but some use a psi as high as 500 for standard jobs. For more delicate fabrics, such as thinning cotton or nylon, you may need to go as low as 50 psi.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
I have a Bissell Pro 2x carpet cleaner. The water heats properly as well as spraying the cleaning product. However, when I go to suction the water from the carpets, the 2 in 1 water tank bladder works properly but there is no dirty water outside the bladder. I have only used this carpet cleaner ~ 5 times and in the beginning I had to empty the suctioned water quite frequently as it was dirty and it could not not hold any more water. So I have done 1 room and all the dirt remains in the carpet
ANSWER : Check that the suction cone is not blocked. Check that the filter or hose to the bladder isn’t blocked as well.
Read Full Q/A … : Dirt Devil CE6000 Featherlite Wet/Dry Vacuum
I have a Bissel 9300-C 0714 BC Carpet Shampooer. It was working great and all of a sudden it stopped working. It still sucks up dirty water but it does not spray water onto the carpet. I can get it to spray water through the smallest hand attatchment but not through the large hand held piece on the base of the machine. I really hope you can help me, I am a dog groomer and I really need my machine to work properly. I can get it to spray water out of the smallest hand attatchment but
that’s all t
that’s all t
ANSWER : The spray jet has become clogged from the soap…. just clean it out. same thing happened to my attachment.
Read Full Q/A … : Dirt Devil CE6000 Featherlite Wet/Dry Vacuum
Have a Bissell Proheat2 will not spray water from the carpet power head but sprays from tools setting Does anyone know how to get water to spray or clean out water
ANSWER : I had this problem. It was small pieces of debris that got into the solution lines and clogged all the nozzles. There is a nozzle for the handheld attachments, one on the front of the machine for spraying spots and two nozzles underneath just behind the rotating brushes.
.
.It was a royal pain disconnecting the clear rubber hoses inside the machine and blowing out the nozzles and the hoses with compressed air. If you are mechanically challenged I’d suggest you take the machine to a vacuum/steam cleaner repair facility.
.
.I’m not sure how the debris got into the solution system, but it may have been when the dirty water tank was emptied some of the dirty water entered the internal, clean water bladder.
.
.A note to Bissell engineers: This issue can be prevented if you simply add an easily accessable solution and/or water filter that the customers can remove, clean and reinstall. Just a suggestion.
.
.It was a royal pain disconnecting the clear rubber hoses inside the machine and blowing out the nozzles and the hoses with compressed air. If you are mechanically challenged I’d suggest you take the machine to a vacuum/steam cleaner repair facility.
.
.I’m not sure how the debris got into the solution system, but it may have been when the dirty water tank was emptied some of the dirty water entered the internal, clean water bladder.
.
.A note to Bissell engineers: This issue can be prevented if you simply add an easily accessable solution and/or water filter that the customers can remove, clean and reinstall. Just a suggestion.
Read Full Q/A … : Dirt Devil CE6000 Featherlite Wet/Dry Vacuum
I have a Bissell Proheat 2XTurbo carpet cleaner. No water will come out when I squeeze the trigger. I have filled the solution tank and the water tank. I read the troubleshooting in the manual and have tried turning it off for a minute and restarting and nothing. I took out both tanks and reseated them and nothing. It has sat for over a year but did not have any water in the water tank. Some solution was left in the solution tank. How can I make the water come out? HELP!
ANSWER :
Call BISSELL Consumer Services.
.
1-800-237-7691
.
Mon-Fri: 8am to 10pm ET
.
Sat: 9am to 8pm ET
Read Full Q/A … : Dirt Devil CE6000 Featherlite Wet/Dry Vacuum
I do not have my users manual and have never vacuumed wet with this vacuum. How do I change it from a dry to wet vacuum.
Can’t find my manual and I need to use the shop vac for water in basement, do I have to change the filter or what
lost my user manual never used it to pick up water. need to know how to puit it in wet mode i want to clean the dirty water out of my pool.
Can’t find my manual and I need to use the shop vac for water in basement, do I have to change the filter or what
lost my user manual never used it to pick up water. need to know how to puit it in wet mode i want to clean the dirty water out of my pool.
ANSWER : .Vacuuming Liquids
.1. When picking up small amounts of liquid
.the filter may be left in place.
.2. When picking up large amounts of liquid
.we recommend that the filter be
.removed. If the filter is not removed, it
.will become saturated and misting
.may appear in the exhaust.
.3. After using the vac to pick up liquids,
.the filter must be dried to reduce the
.risk of possible mildew and damage to
.the filter.
.4. When the liquid in the drum reaches a
.predetermined level, the float mechanism
.will rise automatically to cut off
.airflow. When this happens, turn off
.the vac, unplug the power cord, and
.empty the drum. You will know that the
.float has risen because vac airflow
.ceases and the motor noise will
.become higher in pitch, due to
.increased motor speed.
.IMPORTANT: To reduce the risk of damage
.to the vac do not run motor with float
.in raised position
.1. When picking up small amounts of liquid
.the filter may be left in place.
.2. When picking up large amounts of liquid
.we recommend that the filter be
.removed. If the filter is not removed, it
.will become saturated and misting
.may appear in the exhaust.
.3. After using the vac to pick up liquids,
.the filter must be dried to reduce the
.risk of possible mildew and damage to
.the filter.
.4. When the liquid in the drum reaches a
.predetermined level, the float mechanism
.will rise automatically to cut off
.airflow. When this happens, turn off
.the vac, unplug the power cord, and
.empty the drum. You will know that the
.float has risen because vac airflow
.ceases and the motor noise will
.become higher in pitch, due to
.increased motor speed.
.IMPORTANT: To reduce the risk of damage
.to the vac do not run motor with float
.in raised position
Read Full Q/A … : Dirt Devil CE6000 Featherlite Wet/Dry Vacuum
I have a bissell quickwash 1950-e. I bought it Jan. 2006, and have only used it 8-10 times, I live in a very hard water area, so I though if I put some vinegar in with the cleaning solution it would get rid of any hard water deposits, unfortunatly the solution went lumpy in the tank and stoped spraying out water, I have opened it, hose clean, sprayer not blocked, x at bottom of water container when depresed water trickles out, component that opens the x when water container placed, also ran wate
ANSWER : Hard to say what is causing your problem, replacing the cap and insert on the water tank may help, part #2041111, even tho it may trickle out water when depressed, they can still be bad. The other thing would be the rod not relesing the water like it should. The big draw back to this model is Bissell has obsoleted all of its parts and most are no longer available. Might be wiser to buy new.
Read Full Q/A … : Dirt Devil CE6000 Featherlite Wet/Dry Vacuum
I have the Bissell 2x proheat. There is no water being sucked up from the bladder and the cleaning solution is not being sucked in either in order to get to the carpet. On water rinse the carpet gets wet but I’m not seeing any water going through the clear front piece. I live in Harvest Alabama. Where can I take it to get fixed if it needs it?
ANSWER : Hi,
Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.
Bissell Proheat Upright Wet/Dry Vacuum Problems
heatman101 .
.retqwe
Read Full Q/A … : Dirt Devil CE6000 Featherlite Wet/Dry Vacuum
Sucks but does not spray water. Everything seems to be turning and working. My dog was sick and it sucked up the stain after I sprayed the stain by hand. But it does not rinse or spray liquid any kind onto the carpet to shampoo it.
ANSWER : Have you checked the nosel were the water come out for blockages ?. try dismatal it and clean though with water cold.
.
.more advice contact your manaual
.
.more advice contact your manaual
Read Full Q/A … : Dirt Devil CE6000 Featherlite Wet/Dry Vacuum
