s and so on.
Dyson DC31 Animal Bagless Handheld Cyclonic Vacuum\015 It stops every 2 seconds and will not charge beyond red. I have tried another battery but no change.\015
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
One of the first things to do when your Dyson vacuum cleaner keeps starting and stopping is to empty the bin. It may be full, or the machine may simply perceive it as too full to continue working. Dyson vacuum cleaners require constant airflow through them to work, and a full bin can stop this from happening.
Hot environments speed up battery aging. So it`s best to avoid cleaning the car in hot weather or leaving your vacuum in rooms that experience direct sunlight for prolonged periods. The same goes for cold porches and garages in winter.
When your Dyson no longer powers on even after charging the most likely cause is a damaged battery. This means the battery will no longer hold a charge and will need to be replaced. Once a new battery is purchased you can learn how to replace it by visiting our battery replacement page here.
A clog is a common (perhaps the most common) reason that a Dyson unit loses suction. They have a number of choke points in the airflow paths. Some considerations follow: Hoses: because of their often rough inner surfaces and inevitable bends, hoses are prime locations for clogs.
Ensure the filter is clean and properly installed to stop your Dyson from pulsing. Additionally, try removing any blockages in the airway and check for any kinks in the hose. You also need to check the motor and suction setting to ensure the optimal functioning of the machine.
1 solid blue light will indicate the machine has a low level of charge. If the machine is cutting out/pulsating, this will indicate a blockage. Be careful not to pull the `ON` trigger while looking for blockages.
The Dyson V6 is designed so that you can store the unit on the charger. Storing the Dyson on the charger will not harm the battery and it is not necessary to use the unit until the battery is depleted.
If your vacuum cleaner has lost suction power, it`s time to empty the container. Vacuum cleaners come with various foam or mesh filters. These might get clogged over time if not cleaned or replaced properly. This will cause your vacuum to lose suction.
We recommend replacing your air purifier filter every 12 months. That`s because over time, filters can get clogged with pollutants, and even let unpleasant odors back into the room.
If your vacuum cleaner had a strong acrid burning smell before it lost power then the chances are the motor has failed which will require a motor replacement.
In many cases, you probably can repair a Dyson yourself, especially when it comes to common issues (see below). However, even if your machine needs some extra TLC by a Dyson expert, it can be worth getting it repaired.
Yes, replacing a Dyson V6 battery is possible with the proper tools and knowledge of the steps. Just make sure to get a screwdriver set with a rubber handle, which will make it easier to loosen the bolts.
The battery pack of the Dyson v6 Absolute provides 20 minutes of powerful, consistent suction on a 3.5-hour charge. It is easily removed and replaced.
Check the LED light to determine the battery level. A solid blue light indicates that the machine is in normal operating mode. A flashing blue light indicates that there is no power, and the battery needs to be charged for a minimum of 3.5 hours.
It can take up to four hours to fully charge your battery. Your battery has been designed to be left on charge. Your machine won`t operate or charge if the ambient temperature is below 5°C (41°F).
Wash filters in cold water only
(don`t use detergent or wash in a dishwasher or washing machine). Rinsing under the water supply then gently squeezing the water out of the filter. Repeat until the water runs clear.
It`s important to fully charge the vacuum before using it for the first time, and after every clean. This helps to improve the algorithm`s accuracy. The battery is designed to be left on charge permanently, and this will ensure that the vacuum is fully charged when it`s next used.
Dyson cordless vacuums
Heavy duty performance for big cleans on all floor types. Lightweight and versatile for everyday use.
Clog located in the vacuum hose
Turn the unit on and feel the suction at the end of the hose handle. If there is no or low suction, then the clog is in the hose. You can remove the clog by running a long, stiff object through the hose, such as a butter knife, starting at the wall end.
Eventually, the filters will be clogged and the air flow going through the machine will be dramatically reduced. If no more air is going through the product, the air won`t be cleaned anymore.
One of the easiest ways to increase vacuum cleaner suction is to empty the dust bag or container. Dust containers need to have enough space for airflow, otherwise, they could get clogged and have less suction power. Regularly check your dust compartment and empty or change it when it`s already 70-80% full.
The most common cause of vacuum pump failure occurs due to broken belts, electrical problems inside the unit, or vacuum hoses that fail.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
I have the same problem as steve967 The dyson dc16 is fully charged, runs well for 5-10 seconds and shuts down. I wait for a second or 2 and it runs again for 5-10 seconds. This will continue for numerous cycles, until I am finished cleaning. I have cleaned all the filters, and the power is good, The system will just not stay on. It is just over 2 years old. A friend of mine had the same problem with his Dyson DC16 after just a couple of months and has replaced his Dyson with a Black N De
ANSWER : Dear Michael_Stad,
I am going to sound like a broken record but here is my same answer to another person with the same problem.
I have I had the same problem with my Dyson DC16, where it only runs for a few.seconds at a time with each trigger pull. My husband called Dyson.(Canada) and without hassle they shipped us a replacement part which I.just received this morning. The replacement part sent to us is: DC16.Main Body with Rating Plate. It is also under warranty for 1 year. The.great customer service makes up for the flaw in the machine. Also,.Dyson is aware of the problem. Hope this helps.
Read Full Q/A … : Dyson DC31 Animal Bagless Handheld Cyclonic Vacuum
Hi, this is our third Dyson DC-16.. the Trigger was shorting out on the first two.. Now we have the third one for about a year.. on charge when not using it.. don’t use it every day, but for quick pickups only.. Just how long should the battery last? I was sent a new charger, didn’t help.. it just won’t hold the charge even tho two green lights are solid, but one red light does show up..
ANSWER : How are you charging your battery? Every battery has a memory. If you dont let it die the first come times then charge to full the battery will assume 40% is 100%.
Read Full Q/A … : Dyson DC31 Animal Bagless Handheld Cyclonic Vacuum
My DC 16 will only run for a second each trigger pull. The battery is fully charged, it has plenty of suction, just wont run for more than a second. I cleaned the filters.
ANSWER : I had the same problem with my Dyson DC16, where it only runs for a few seconds at a time with each trigger pull. My husband called Dyson (Canada) and without hassle they shipped us a replacement part which I just received this morning. The replacement part sent to us is: DC16 Main Body with Rating Plate. It is also under warranty for 1 year. The great customer service makes up for the flaw in the machine. Also, Dyson is aware of the problem. Hope this helps.
Read Full Q/A … : Dyson DC31 Animal Bagless Handheld Cyclonic Vacuum
This is embarassing, but I have just looked at the Dyson DC07 manual and at my Dyson for about 20 minutes, and I can’t for the life of me find the wand release button on my actual Dyson…..the manual pictures don’t look like the parts on my Dyson….I don’t have a hose with a wand release button….the hose just goes straight up inside the handle….Can someone help me? Thanks 🙂
ANSWER : Hi the wand release button is located directly above the the Cylinder release button. The wand release button looks like the picture below. In order to releease the wand you must firstly make sure the Electrical cable is not wrapped up for storage. So unwrap the electrical cable. then find the item as in the picture. Press this button in and at the same time lift the wand. This will realease the wand from the spine of the Dyson. 
Read Full Q/A … : Dyson DC31 Animal Bagless Handheld Cyclonic Vacuum
My Dyson DC31 runs for a few seconds then cuts out and won’t work at all. It is fully charged. We bought it just over 2 years ago and it has worked perfectly until now. It is clean and has no apparent blockages. Please can you help?
ANSWER : Hi Jean, it’s Jack at Dyson.
I’m sorry to hear you’re having difficulty with your DC31. If it cuts out in use when it’s fully charged, we’d need to take you through some quick diagnostic checks when you have the machine at hand. This will help our experts determine what may be causing the issue.
Please give our customer Helpline a call on 0800 298 0298 (UK), or 1-866-693-9766 (US). We’ll look forward to hearing from you.
Best wishes,
Jack
Dyson Online Customer Support
www.dyson.com
Read Full Q/A … : Dyson DC31 Animal Bagless Handheld Cyclonic Vacuum
My handheld dyson won’t charge but when I hold the trigger the lights come on?
ANSWER : Hi Lynora,
I am sorry to hear you are having difficulty with your DC16. Based on the details you provided we would appreciate the opportunity to trouble shoot with you over the phone to determine the best solution.
Please call us at 1-866-693-9766 US or 0800 298 0298 UK. We look forward to speaking with you.
Best wishes,
Jessica
I am sorry to hear you are having difficulty with your DC16. Based on the details you provided we would appreciate the opportunity to trouble shoot with you over the phone to determine the best solution.
Please call us at 1-866-693-9766 US or 0800 298 0298 UK. We look forward to speaking with you.
Best wishes,
Jessica
Read Full Q/A … : Dyson DC31 Animal Bagless Handheld Cyclonic Vacuum
The motor running the beater bar on ny Electrolux canister vacuum cleaner runs intermittently. It runs about 2 minutes and then cuts off and automatically starts again after a 1 to 2 minute interval. I have tried taking it apart and removing the dust and grit in the beater bar attachment but with no change in operation. What would you suggest?
ANSWER : Check all the wiring connections to make sure they’re tight.
.1/2. Wiring to power nozzle motor or reset switch is loose.
.1. Cord from power nozzle to upper wand. If the plastic portion of the wand is cracked near the cord connection, or the connections are blackened, they need replaced.
.2. Wiring connection from hose handle to upper wand. Check for cracks and discoloration as in 1 above. Replace if necessary.
.3. Hose connection to vacuum. Not likely, but possible.
.4. There could very well be a break in the hose wiring.
.You may need to take your vacuum, with hose and power nozzle, to an authorized Aerus Electrux service shop. They can try a new hoze to see if that’s the problem. If there is a break in the wiring, the hose is probably worn in other areas as well, and should be replaced.
.1/2. Wiring to power nozzle motor or reset switch is loose.
.1. Cord from power nozzle to upper wand. If the plastic portion of the wand is cracked near the cord connection, or the connections are blackened, they need replaced.
.2. Wiring connection from hose handle to upper wand. Check for cracks and discoloration as in 1 above. Replace if necessary.
.3. Hose connection to vacuum. Not likely, but possible.
.4. There could very well be a break in the hose wiring.
.You may need to take your vacuum, with hose and power nozzle, to an authorized Aerus Electrux service shop. They can try a new hoze to see if that’s the problem. If there is a break in the wiring, the hose is probably worn in other areas as well, and should be replaced.
Read Full Q/A … : Dyson DC31 Animal Bagless Handheld Cyclonic Vacuum
On the DC07, the entire cyclone assembly must be removed to empty the dust, debris, etc. collected when vacuuming. On the top of the cyclone is a “trigger” that you lift with your finger to release the bottom catch, which allows a clear flap to open on the “clear bin,” thus letting all the debris fall out. My problem is when you lift the finger trigger, it does not release the catch on the bottom. Since the catch won’t release, I cannot remove the entire clear bin either from the cyclone.Any sug
ANSWER : Beofre you go to the extent of buying a replacement canister, you can remove the top and using a straightened coat hanger type thing open that bottom lid. Then maybe you can clean the rim and possibly add some silicone spry to loosen things up. Here’s how to get inside In this order: 1) Remove the canister 2) remove the three star screws at the top of the canister. It’ll take a bit of pressure to pull the top up, there’s a rubber seal. When you pull it up there will be a rod running down into the canister, leave it be, just pull up the top high enough to clear out any debris. 3) Use a straightened coat hanger and with a flashlight to guide you, reach down with it and push it into that hole down at the bottom center of the canister. That will pop the lid open. Clean the canister & lid rims, maybe add some silicone. At this point you might as well clean the canister too. OPTIONAL-> ***leave the bottom lid open*** and follow the rest of these steps 4) Put the top back on aligning the screws, when you lower it make sure the bottom of the rod engages with the hole at the bottom center of the canister, this is why you left the bottom lid open. Put the three star screws back in. 4) Turn the canister upside down, lid open, and keeping in mind this is thin plastic, gently tug upwards on the four fins that surround the bottom rubber seal. This part is held in by friction, so work your way around the four fins gently pulling until you work the ring they’re connected to free. This will give you access to the inside of the canister. 5) remove the round perforated section by tugging upwards on it, set it aside with the fin part. 6) Take the canister to a laundry tub or large sink and holding it bottom up fill it with hot/warm water. Grasping the center section shake it vigorously and turn it upside down while shaking and a bunch of sh*t will come out. Repeat several times. 7) Dry thoroughly, you might use a hairdryer held to the center tube, but only if you can switch off the heat and use air only. Make sure its 200% dry, water will kill your machine 8) clean and replace the round perforated section 9) replace the fin section, I’d suggest pulling the round rubber part off of the fin part and setting it in place on the canister first, then follow with the plastic fin part. If you don’t do it this way the rubber won’t seat properly and the bottom lid won’t close. 10) Close the lid, replace the canister, and staaaaaart suckin like it’s brand new.
Read Full Q/A … : Dyson DC31 Animal Bagless Handheld Cyclonic Vacuum
