Dyson Ball DC24 Bagless Upright Vacuum
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
Loss of suction in your DC25, like most other Dysons, is usually caused by one of four things: Blocked or damaged filters. Splits or tears in your hosing and seals. Blockages in your ducting or.
A clog is a common (perhaps the most common) reason that a Dyson unit loses suction. They have a number of choke points in the airflow paths. Some considerations follow: Hoses: because of their often rough inner surfaces and inevitable bends, hoses are prime locations for clogs.
It may be full, or the machine may simply perceive it as too full to continue working. Dyson vacuum cleaners require constant airflow through them to work, and a full bin can stop this from happening. Make sure there`s no dirt lodged in the top part of the bin.
Loose connections will cause your vacuum cleaner to lose suction. Make sure that the dust container, the hose, the tube and the brush are all attached properly. If the problem continues, your vacuum cleaner might have a technical problem. If you suspect this to be the case, contact an authorised service agent.
Vacuum cleaners are fairly simple machines. They need power to be transmitted to the vacuum to create a suction force that lifts debris. So, the usual areas that cause suction loss include the wrong height setting, stuck rollers, a faulty gasket, a broken vacuum belt, a filled bag, or a clogged hose.
The use of an extension cable is not recommended.
To reset the Brush bar press the Brush bar control button twice or switch the machine off and back on. Please note: In normal use, the Brush bar automatically turns off when the machine is upright and automatically turns on when the machine is in the vacuuming position.
It`s possible there`s a power consumption issue, with there just not being enough residual charge to run the machine. A new battery should fix this. My other thought is that it`s overheating. If too much power is pushed through the motor, which MAX power does, it could stop after a few seconds if it become hot.
A Dyson handheld that keeps cutting out is known as pulsing. A Dyson V7 pulsing problem can be very frustrating! A few reasons why your Dyson is pulsing are potential blockages or problems with the bin or filter.
One of the easiest ways to increase vacuum cleaner suction is to empty the dust bag or container. Dust containers need to have enough space for airflow, otherwise, they could get clogged and have less suction power. Regularly check your dust compartment and empty or change it when it`s already 70-80% full.
Vacuum means the absence of all matter including air. As there is no air in the vacuum, air pressure will be zero.
We have two possible ways of adjusting the pressure in a vacuum system: first, by changing the pumping speed (altering the speed of the pump or throttling by closing a valve); second, through admission of gas (opening a valve).
Clog located in the vacuum hose
Turn the unit on and feel the suction at the end of the hose handle. If there is no or low suction, then the clog is in the hose. You can remove the clog by running a long, stiff object through the hose, such as a butter knife, starting at the wall end.
Boil old suction cups to revive them.
Take the pot off of heat and drop your suction cups in for about 30 seconds. Take them out with a pair of tongs and pat them dry on a lint-free towel. Try to use the suction cups right after you dry so they`re still warm and flexible.
The most common problems found in vacuum cleaners are low suction force, excessive noise, burning smell, vacuum not turn on, and overheating. These issues can be fixed by either cleaning the device or replacing some parts of the device. At times, it is best to seek a professional to fix the cleaner effectively.
Depending on your Dyson model, you may be surprised by the amount of dust and debris you`ll find inside it. So, `detach the hose from the wand, then clean its insides using a cloth pushed inside with the help of a broomstick or anything similar. `
While surge protectors will protect most of your belongings, there are a few items that you shouldn`t plug into them. Vacuum cleaners draw a high current load, which can damage the surge protector. Never plug a space heater, air conditioner or electric motor into a surge protector.
And an extension cord with a retractable reel takes almost all of the cord headache out of the vacuuming equation. To use one, find as central of a location as you can, preferably in a spot that won`t cause you to wind around too much furniture, plug in your extension cord, and plug your vacuum cleaner into that.
Max or Boost modes are meant for powerful, intensive bursts of spot cleaning. Using them constantly speeds up degradation of the battery. If your machine has Eco mode, run time is maximized for a longer clean.
Yes you do still have to hold the trigger down. I am sure this is an energy management thing to make the battery last longer by not running constantly.
Replace the Brush Belt
If the vacuum is still hard to push, tilt it back far enough that you can inspect the moving brush while the vacuum is running. Be careful to avoid getting too close to the moving parts. If you see that the brush is not turning, that means you will need to replace the brush belt.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
Poor Suction Heya! So I just picked up a used Dyson, but when I vacuum with it, the suction is pretty weak and it spits all kinds of stuff out the back and into my feet. When I pull the hose I have good suction, but in regular mode it hardly picks up anything. The brushes are spinning, and it eventually will clean an area if I go over it again and again. Maybe a clog somewhere? Please tell me that Dysons have better suction than my $50 Dirt Devil! Thanks!
ANSWER : I recently bought a second hand Dyson DC07. Its suction was poor. I removed all the un-clipable pipe bits and to remove any blockage but it all looked clear. The Final Sponge and hepper filter did have a lot of dust in it and the rotating brush was full of hair but nothing bad.
.
.I eventual gave in to curiosity and removed the three screws in the top or the yellow removable dust collection tube and cyclone bit to see what was in there. The mechanism to release the flap at the bottom of the collection tube does not allow you to remove the lid completely but it does open far enough to get inside. I found the whole top section of the yellow plastic bit blocked by a big plug of compacted dust and a champagne cork. If you are willing to take the risk and have a torx 15 screwdriver handy it that part may be blocked. It did get a bit messy.
.
.If I was going to attempt the same procedure I’d remove the dust collection unit from the vacuum cleaner as I did before, but leave the clear tube attached and the emptying flap firmly closed to reduce the mess from the dust falling out the bottom while cleaning the top part.
.
.I eventual gave in to curiosity and removed the three screws in the top or the yellow removable dust collection tube and cyclone bit to see what was in there. The mechanism to release the flap at the bottom of the collection tube does not allow you to remove the lid completely but it does open far enough to get inside. I found the whole top section of the yellow plastic bit blocked by a big plug of compacted dust and a champagne cork. If you are willing to take the risk and have a torx 15 screwdriver handy it that part may be blocked. It did get a bit messy.
.
.If I was going to attempt the same procedure I’d remove the dust collection unit from the vacuum cleaner as I did before, but leave the clear tube attached and the emptying flap firmly closed to reduce the mess from the dust falling out the bottom while cleaning the top part.
Read Full Q/A … : Dyson Ball DC24 Bagless Upright Vacuum
No suction Hello – any help with this would be much appreciated!
I just changed the bag and filters. The machine runs, seems normal, but there is no suction. There is no blockage of the hose, as indicated by the fact that that little viewer window above where the hose connects to the unit is not showing the red portion that it shows when there is something blocking the hose (god, this is hard to describe!).
If I disconnect the hose and put my hand over the hole, I feel some suction. But
ANSWER : Well, it actually sounds like there is a blockage. Try removing your hose and dropping something through it, like a quqrter. If it comes through, no clog. If it is clogged, I believe that machine has a blower on the upper part of the cleaner (maybe in the bag compartment towards the top. You can take out the filter holder and plug the hose in there and run the unit . Does the blockage come out? If not, Try shaking the hose, or you can put a stiff wire in it to try to free it. Do not run water through it. If there is no blockage at all, then you will probably need to take it to a service center. But I am pretty confident that we are looking at a clog situation. Let me know if this fixesya! Thanks, Rene (vacuum Doctor)
Read Full Q/A … : Dyson Ball DC24 Bagless Upright Vacuum
No Suction I get great suction in the hose, but when I plug the hose back into the unit, there is no suction and the air flow indicator line goes completely red. I've changed the bag and filters. I took the small panel off the back and made sure there is no clog, and took the hose off to make sure there was no clog there. Still no suction. Please help.
ANSWER : I about to say that’s always a clog of some sort that causes that
Read Full Q/A … : Dyson Ball DC24 Bagless Upright Vacuum
No suction Just received my refurb. dyson animal bagless. Finally figured out how to get it all together, turned it on and there is no suction coming up thru the beater bar. The hair is just collecting around the bar and not going up into the canister. It appears all the suction is going thru the open red end of the attachment hose, which has a vented cover piece. Am I missing a piece or is there a switch to turn of the attachment suction?
ANSWER : So the red hose isn’t connected to a part on the vaccum so like it is connected to the connester but not to an opening just above the beater bar, this is the only idea i can supply you with. good luck, maybe i got lucky and helped you out.
Read Full Q/A … : Dyson Ball DC24 Bagless Upright Vacuum
My dyson seems to have lost its suction therefore is not picking up anything yet i have found that when my dyson is standing upright it has a little more suction but nothing like how it use to work. This has only happend in the last 2 weeks. I sanded a floor & though the sander picked up majority of the dust i did use the dyson to pick up the excess and it is since then that my dyson has not been working to its full potential.
ANSWER : Hi there,
.
.Sorry to hear you’re having a problem with your DC07. You should be able to resolve the issue by following these simple steps: http://www.dyson.co.uk/support/help.asp?article=1940&product=DC07-SY
.
.If you’re still experiencing difficulties, please get in touch with us, free, on 08002980298 (UK), or 1866MYDYSON (US), so we can run through some checks over the phone.
.
.Kind regards,
.
.Jack
.Dyson Customer Service
.
.Sorry to hear you’re having a problem with your DC07. You should be able to resolve the issue by following these simple steps: http://www.dyson.co.uk/support/help.asp?article=1940&product=DC07-SY
.
.If you’re still experiencing difficulties, please get in touch with us, free, on 08002980298 (UK), or 1866MYDYSON (US), so we can run through some checks over the phone.
.
.Kind regards,
.
.Jack
.Dyson Customer Service
Read Full Q/A … : Dyson Ball DC24 Bagless Upright Vacuum
This is embarassing, but I have just looked at the Dyson DC07 manual and at my Dyson for about 20 minutes, and I can’t for the life of me find the wand release button on my actual Dyson…..the manual pictures don’t look like the parts on my Dyson….I don’t have a hose with a wand release button….the hose just goes straight up inside the handle….Can someone help me? Thanks 🙂
ANSWER : Hi the wand release button is located directly above the the Cylinder release button. The wand release button looks like the picture below. In order to releease the wand you must firstly make sure the Electrical cable is not wrapped up for storage. So unwrap the electrical cable. then find the item as in the picture. Press this button in and at the same time lift the wand. This will realease the wand from the spine of the Dyson. 
Read Full Q/A … : Dyson Ball DC24 Bagless Upright Vacuum
Lost suction my DCO7 lost suction in the hose I started taking it apart and cleaning it and looking for clogs (probably more than I should have) and when I put it back together it has awesome suction in the hose but no suction in the base. It just pulls the pine needles up (christmas tree) but they never appear in the “bag” compartment and when I look they are just all gathered in a clump in the bottom by the brush.
ANSWER : Hi.
.
.Remove the sole plate turn the 3 plastic screws to unlock & lift off.
.
.Now remove the blockages that have accumilated from the oppening of short clear hose.
.Check you can turn brush roller & check belt.
.
.Now reassemble switch on pull handle back & look under machine is brush spinning ?
.
.If not check the knob on side of machine is in drive (D) position.
.
.http://dysonmanuals.llc.nu
.
.Chris..
.
.Remove the sole plate turn the 3 plastic screws to unlock & lift off.
.
.Now remove the blockages that have accumilated from the oppening of short clear hose.
.Check you can turn brush roller & check belt.
.
.Now reassemble switch on pull handle back & look under machine is brush spinning ?
.
.If not check the knob on side of machine is in drive (D) position.
.
.http://dysonmanuals.llc.nu
.
.Chris..
Read Full Q/A … : Dyson Ball DC24 Bagless Upright Vacuum
My DC17 suction hose doesn’t have any suction occasionally.
ANSWER : Check the seal on the filter is not broken,And check for any blockage at the bottom of the pickup pipe.
Read Full Q/A … : Dyson Ball DC24 Bagless Upright Vacuum
