Eureka 431A Optima Bagless Upright Vacuum
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
The air filter traps particles as the air travels through the vacuum cleaner. If the filter is clogged, the vacuum cleaner will not have proper suction. If your vacuum filter is clogged, refer to your owner`s manual for cleaning instructions.
To reset the thermostat, press the vacuum`s power button into off position and unplug the vacuum. Check the vacuum for potential causes of overheating, such as clogs or a full dust cup, and allow the vacuum to set and cool off for 30 minutes before turning it back on.
Push a broomstick through the hose to force any large clogs out. Take the end of the broomstick and feed it through the hose. Push the stick in slowly so you don`t accidentally break or puncture the hose. If there is a large clog in your hose, the broomstick will force it out from the other end.
Loose connections will cause your vacuum cleaner to lose suction. Make sure that the dust container, the hose, the tube and the brush are all attached properly. If the problem continues, your vacuum cleaner might have a technical problem. If you suspect this to be the case, contact an authorised service agent.
One of the easiest ways to increase vacuum cleaner suction is to empty the dust bag or container. Dust containers need to have enough space for airflow, otherwise, they could get clogged and have less suction power. Regularly check your dust compartment and empty or change it when it`s already 70-80% full.
Low compression, an intake leak or tight valves also can cause low vacuum at idle. If the vacuum reading fluctuates within the normal range-the gauge needle bounces around a lot-uneven compression (broken rings or leaking valves or head gasket in one or two cylinders) is a likely culprit.
A vacuum reading at idle that is much lower than normal might indicate leakage through the intake manifold gaskets, manifold to carburetor gaskets, vacuum brake booster or the vacuum modulator. Low readings could also be caused by very late valve timing or worn piston rings.
Durable – Vacuums made by Eureka are known to last for many years, maintaining the same level of quality cleaning power as the day they were first put into use.
Currently, the most common and simple method for patients, caregivers, and health professionals to unclog the drain tube is through stripping. Stripping involves squeezing one`s fingers along the length of the tube and pushing down any clots and debris into the suction bulb.
The suction power is to be measured at the end of the tube of a complete vacuum cleaner (i.e. with tube, hose and filters – but without nozzle). Some manufacturers show the results from measurements made at the suction of the actual vacuum cleaner.
Founded in 1909 in Detroit, Michigan Eureka vacuums have been in American`s homes for more than a century. Now we`re building on that experience with innovative cleaning technology to help you clean for years to come.
Clog located in the vacuum hose
Turn the unit on and feel the suction at the end of the hose handle. If there is no or low suction, then the clog is in the hose. You can remove the clog by running a long, stiff object through the hose, such as a butter knife, starting at the wall end.
Clog located in the vacuum hose
Turn the unit on and feel the suction at the end of the hose handle. If there is no or low suction, then the clog is in the hose. You can remove the clog by running a long, stiff object through the hose, such as a butter knife, starting at the wall end.
It is obtained by measuring how many inches up a tube the vacuum motor`s intake can pull up, or lift, the water. For the Water Lift test, there is no air moving through the motor. It is a sealed suction measurement to find the pure suction force of the motor.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
My Hoover vacuum is not vacuuming the carpets or floors. When I release the tube to use the smaller end the suction works perfect. So i believe the problem is in the rods on the floor or in the part that vacuums the floor! Can you tell me how to fix it , or where can I take it to get it fixed?
thanks
ANSWER : Ive just had the exact same problem. In the very back lower portion of the vacuum You will need to take it apart. I guarantee there is a clog. You might also check your belts to make sure they are still on track.
Read Full Q/A … : Eureka 431A Optima Bagless Upright Vacuum
I purchased a brand new Eureka Pet vacuum, sorry don’t know exact name but it the one that has the self cleaning duster on it. Last night I used the vacuum on my carpet, it was working fine until I accidently sucked up the corner of a scarf that was hanging off a couch. I shut the vacuum off, pulled out the scarf and and resumed vacuuming. Much to my dismay the suction on the vacuum had ceased. Can you tell me if there is a reset button on the vacuum? The vacuum does not appear to be damage
ANSWER : If the motor is running, there should be suction. Possible problems depend on whether it’s a canister or upright and are:
.A clog in the hose, UR or canister. Detach hose. Drop small coin in one end and lift hose causing it to roll out the other. If it does, no clog in hose. Drop same coin into hose opening on power head. If it rolls out, no clog in PN.
.Broken fan blades, UR. Needs to be taken to shop for repair/replacement.
.
.A reset button is for use if the motor isn’t running, so won’t have anything to do with the suction.
.A clog in the hose, UR or canister. Detach hose. Drop small coin in one end and lift hose causing it to roll out the other. If it does, no clog in hose. Drop same coin into hose opening on power head. If it rolls out, no clog in PN.
.Broken fan blades, UR. Needs to be taken to shop for repair/replacement.
.
.A reset button is for use if the motor isn’t running, so won’t have anything to do with the suction.
Read Full Q/A … : Eureka 431A Optima Bagless Upright Vacuum
Dirt devil vacuum cleaner–trouble vacuuming dirt and pet hair on carpeting –is the problem with the spinning brush which contacts the floor, not contacting the carpeting?? I thought (when I bought this vacuum) that the aforementioned brush was adjustable to various heights of carpeting. Sometimes, it seems like nothing is being vacuumed up –unless I have just put a new bag on the vacuum… Do I need or can I replace the spinning brush on the bottom of the vacuum so it kicks up and vacuums
ANSWER : Try replacing the belt. Rubber belts stretch out after about a year.
Read Full Q/A … : Eureka 431A Optima Bagless Upright Vacuum
My Eureka Optima vacuum doesn’t have any suction when on the floor option. How can I fix this?
ANSWER : It will as long as long as your accessory hose is properly inserted into the base. Otherwise the vacuum stays on the hose only.
Read Full Q/A … : Eureka 431A Optima Bagless Upright Vacuum
I have a Eureka Boss Power Plus and the beater bar is rolling, the belt is turning, but after vacuuming up around the litter box (not a lot of litter), when I turn the vacuum off, the litter, or even household dirt, falls out. When I hold the vacuum back to turn it off so that it doesn’t fall on the floor, it’s sitting in the cubby where the wheels are. The bag is empty, the hose is not plugged, the hose is securely fitted on both ends of the unit. This vacuum was purchased in July and is being
ANSWER : Even though the brush is spinning, you probably need to replace the belt
because it is stretched. It is probably slipping on the beater bar. This is normal and you shouldn’t be alarmed. There is nothing wrong with your vacuum. 🙂
because it is stretched. It is probably slipping on the beater bar. This is normal and you shouldn’t be alarmed. There is nothing wrong with your vacuum. 🙂Jim
Read Full Q/A … : Eureka 431A Optima Bagless Upright Vacuum
I purchased a Eureka C4910 last year and have a question that I am hoping you can answer.
There are two motor actions with this vacuum, 1) the vacuum suction, and 2) the beater bar. The action of the beater bar is that motor is supposed to automatically shut off when the handle is in the complete vertical position assuming the vacuum is stationary, but then turn on when the handle is tilted toward the floor, assuming the vacuum is moving back and forth.
The beater bar motor turn-on mechan
ANSWER : Good day!
Normally when the motor is easily moved back and forth means that it have a proper lubrication,proper alignment and no clogs.
When the motor and the belt is OK the problem could be on electrical wiring and switch.
If found electrical switch burned out you need to replaced it because when the switch is burn the contact of that switch is open even you turn it ON.that’s why the motor is not function because the voltage is not pass through the circuit because of open switch.You need to replaced it.
And check some fuses if any and other burned electrical wire.Replaced it also.
Thank you and don’t forget to rate my answer.
Read Full Q/A … : Eureka 431A Optima Bagless Upright Vacuum
No Suction I have the Eureka Upright Vacuum. I have no suction when doing regular vacuuming but it seems to have function with just the hose. Also, the height adjustment doesn’t seem to work at all. The vacuum has only be usede 3 times. Thanks
ANSWER : Is your brush roller turning? unplug the vacuum and see if you can turn the brushroller by hand.if it turns real freely the the belt is broke ,if its real hard to turn then something is caught up around the bearings on the ends of the roller.my suggestion is if your having that much trouble withit take it back and tell them you want a new one.if they want to keep your buisness they will give you a new one
Read Full Q/A … : Eureka 431A Optima Bagless Upright Vacuum
Need Kirby Generation 3 Vacuum cleaner manual. Vacuum is not picking up dirt from floor. Seems to have enough suction to inflate the bag, but when you check the suction under the vacuum, there seems to be extremely litle suction.
ANSWER : If your brush roll is turning and your bag is not overly full, then the only other thing it can be is a clog where the bag connects to the vacuum. Turn the plastic part out away from vacuum and lift off to see if you have something clogging it. It would have to be something big, but not so big that it could not get past the fan. As a rule of thumb, KIRBY never clogs. I suspect that your belt is stretched out and your brush roll is not turning while on the carpet so the brush roll is just in the way rather than brushing your carpet to pick up dirt.
Read Full Q/A … : Eureka 431A Optima Bagless Upright Vacuum
