5 minutes.
Eureka 431A Optima Bagless Upright Vacuum
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
If your vacuum cleaner keeps turning off, this could be due to the following reasons: Blockages – check the hose and head for any obstructions. Filter – always check your filters, if these are clogged this could be causing the vacuum cleaner to work harder and lose suction power.
A damaged vacuum hose, clogged motor air filter or bad suction motor can cause the vacuum cleaner to shut off during use. A tripped overload on the vacuum suction motor can shut off the vacuum cleaner during use. If your vacuum has a reset button, push it; if the vacuum seems hot, let it cool off first.
To reset the thermostat, press the vacuum`s power button into off position and unplug the vacuum. Check the vacuum for potential causes of overheating, such as clogs or a full dust cup, and allow the vacuum to set and cool off for 30 minutes before turning it back on.
Inspect the belt to see if it is broken, stretched out, or out of place. If the drive belt is broken or stretched out, replace it. If the brushroll is sticking, it will cause too much friction and put too much strain on the belt. Remove the brushroll and clean all hair, string, and lint from the brushroll bearings.
A thermal cut off is a heat-sensitive device that automatically disconnects the power to a vacuum`s motor when the operating temperature exceeds a safe value.
Check For Clogs or Blocks In The Vacuum
Check the hoses, the filters, and throughout the vacuum, and clean out any blockages or clogs. Vacuums will likely also have a recommended cooldown time to ensure that the vacuum won`t overheat. You will need to wait for that time before you turn the vacuum back on.
A vacuum cleaner can run continuously for 30 – 60 min each time. The vacuum cleaner has no suction power. For example, a hair cannot be sucked up.
First, test the power switch for continuity to ensure that the brushroll motor is getting power. If the power switch has continuity, ensure that the motor turns freely and is clear of obstructions. If power is getting to the motor, and the motor turns freely, but the motor still won`t run the motor is likely defective.
Durable – Vacuums made by Eureka are known to last for many years, maintaining the same level of quality cleaning power as the day they were first put into use.
Check for a plugged hose:
Plugged vacuum hoses are sometimes the reason for a loss in suction. Hoses can get clogged with hair, dust bunnies, string, or anything else that can`t pass through the other end of the hose. Airways inside the machine should be looked at as well. Wherever there is an air passage, check it.
Founded in 1909 in Detroit, Michigan Eureka vacuums have been in American`s homes for more than a century. Now we`re building on that experience with innovative cleaning technology to help you clean for years to come.
A vacuum cleaner can run continuously for 30 – 60 min each time. The vacuum cleaner has no suction power. For example, a hair cannot be sucked up.
If you find that your machine is turning off intermittently, the filter in your vacuum is most likely full and covering the ventilation system. Remove the filter, then empty and wash it. Allow the filter to dry for at least 24 hours, or until it is completely dry.
A vacuum cleaner can run continuously for 30 – 60 min each time. The vacuum cleaner has no suction power. For example, a hair cannot be sucked up.
Problems can occur when overused or clogged filters cause the vacuum motor to overheat. This not only shortens the motor life but causes a loss of suction. In some cases, total motor burn out can occur.
Check Your Battery & Charger:
Batteries don`t last forever depending on age and use. You may need to buy a new battery if your Dyson vacuum is turning on and off after only a few minutes of use.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
I purchased a brand new Eureka Pet vacuum, sorry don’t know exact name but it the one that has the self cleaning duster on it. Last night I used the vacuum on my carpet, it was working fine until I accidently sucked up the corner of a scarf that was hanging off a couch. I shut the vacuum off, pulled out the scarf and and resumed vacuuming. Much to my dismay the suction on the vacuum had ceased. Can you tell me if there is a reset button on the vacuum? The vacuum does not appear to be damage
ANSWER : If the motor is running, there should be suction. Possible problems depend on whether it’s a canister or upright and are:
.A clog in the hose, UR or canister. Detach hose. Drop small coin in one end and lift hose causing it to roll out the other. If it does, no clog in hose. Drop same coin into hose opening on power head. If it rolls out, no clog in PN.
.Broken fan blades, UR. Needs to be taken to shop for repair/replacement.
.
.A reset button is for use if the motor isn’t running, so won’t have anything to do with the suction.
.A clog in the hose, UR or canister. Detach hose. Drop small coin in one end and lift hose causing it to roll out the other. If it does, no clog in hose. Drop same coin into hose opening on power head. If it rolls out, no clog in PN.
.Broken fan blades, UR. Needs to be taken to shop for repair/replacement.
.
.A reset button is for use if the motor isn’t running, so won’t have anything to do with the suction.
Read Full Q/A … : Eureka 431A Optima Bagless Upright Vacuum
Dirt devil vacuum cleaner–trouble vacuuming dirt and pet hair on carpeting –is the problem with the spinning brush which contacts the floor, not contacting the carpeting?? I thought (when I bought this vacuum) that the aforementioned brush was adjustable to various heights of carpeting. Sometimes, it seems like nothing is being vacuumed up –unless I have just put a new bag on the vacuum… Do I need or can I replace the spinning brush on the bottom of the vacuum so it kicks up and vacuums
ANSWER : Try replacing the belt. Rubber belts stretch out after about a year.
Read Full Q/A … : Eureka 431A Optima Bagless Upright Vacuum
Have a Centralux Aerus about 5 years old. Don’t see a model number. There is suction but beater brush quit working. Was using for a few minutes, shut it off for a few minutes, turned it back on and suction only. Tried the reset button also. Tried the sidekick attachment and it works fine. There was no smell like something was hot. Belt is fine. Are there any fuses or anything else to try? This vacuum cleaner has not really been used that much, it is hard to believe the motor would need replaced
ANSWER : There probably is a loose wire in the handle near the switch or a wire off near the swivel elbow near the vac power head. With the right fastener tool to remove some screws you can fix it yourself
Read Full Q/A … : Eureka 431A Optima Bagless Upright Vacuum
My Dyson Animal has good suction and works fine for actually picking up dirt, but when I use the vacuum with the roller, I hear a grinding/rumbling noise. Its only when I use the vacuum with the brush rotating. It does not happen hen I shut the roller brush off. The belt is fine. I cannot figure out what is wrong as there are no clogs, debris, or foreign objects stuck in the brush or in the belt. The noise seems to be the only issue. The vacuum picks up fine. It just doesn’t sound right a
ANSWER : Trace the path of the suction into the tank and see if there is anything loose or ingested..Also, remove the brush and clean as best you can. Perhaps there is something caught in it. Lubricate where it makes sense with some WD40.
Read Full Q/A … : Eureka 431A Optima Bagless Upright Vacuum
Suction Problem I was vacuuming and stopped to empty the cannister. When I started vacuuming again – the suction wasn’t working properly. The vacuum was just pushing stuff around the floor. I cleaned the hair out the brush on the bottom and it still isn’t working. It was working fine before I emptied the tube 🙁 I can’t figure out what happened.Help!
ANSWER : Greetings from GoVacuum,
.
.I believe what may have happened is that your vacuum cleaner belt has either broken, or been stretched so far that ithe brushes are no longer spinning fast enough.
.
.Here’s what you should do to diagnose this problem.
.
.1. Take the suction hose out of the back of the vacuum (assuming that your vacuum has on-board tools), and see if you have any suction coming from the hose. If you do, this indicates your belt is bad.
.
.2. If you don’t have suction coming from the hose, then it may be something as simple as replacing the filters, to a clog in the vacuum, or to your motor going bad.
.
.In my professional opinion though I would say from what you stated that the belt is mostly likely going to be your issue. If you can provide me the model number of your vacuum cleaner, I can walk you through step by step on ow to replace the belt.
.
.I have posted a short YouTube video on a vacuum belt change, this is not for all vacuums, but it will give you some idea of how to change a belt;
.
.
.
.
.
.I believe what may have happened is that your vacuum cleaner belt has either broken, or been stretched so far that ithe brushes are no longer spinning fast enough.
.
.Here’s what you should do to diagnose this problem.
.
.1. Take the suction hose out of the back of the vacuum (assuming that your vacuum has on-board tools), and see if you have any suction coming from the hose. If you do, this indicates your belt is bad.
.
.2. If you don’t have suction coming from the hose, then it may be something as simple as replacing the filters, to a clog in the vacuum, or to your motor going bad.
.
.In my professional opinion though I would say from what you stated that the belt is mostly likely going to be your issue. If you can provide me the model number of your vacuum cleaner, I can walk you through step by step on ow to replace the belt.
.
.I have posted a short YouTube video on a vacuum belt change, this is not for all vacuums, but it will give you some idea of how to change a belt;
.
.
.
.
Thanks, and if you have questions about your particular model, please feel free to contact me at
.
.[email protected]
.1-866-468-2288
Read Full Q/A … : Eureka 431A Optima Bagless Upright Vacuum
Electrolux vacuum brush not turning problem:
was vacuuming and rug got caught auto shut off kicked off power to brush. instead of hitting red button to restart brush I disconnected brush to vacuum some hair in Conner. after i reconnected the brush and hit the red button but no power to brush. Light won’t even switch on. Hope you can help
ANSWER : Under the vacuum, there is a guard..remove the guard , either by 2 screws or by 2 clips..there is a belt under the guard..that is connected to the brush..the belt need to be replaced.
Read Full Q/A … : Eureka 431A Optima Bagless Upright Vacuum
Nothing inn the canister after using,suctione working,bottom roller working,no air leaks from hoses.Also when running awhile it shuts off by itself,have to wait awhile to use again
ANSWER : I’m not sure what vacuum you have, but that sounds like a blockage to me. Thermal shut off kicks in, shutting the motor down, to prevent damage from overheating. After waiting like 1 hour it probably comes back on. Make sure hose, filters, bag (if any) is clean. All “airways” of vacuums need to be clear of any blockages, since airflow is what makes vacuums work.
Read Full Q/A … : Eureka 431A Optima Bagless Upright Vacuum
The vacuum won’t start. I used it for about an hour and then turned it off and when I went to turn it back on ..there was no response. I cleaned every compartment on the machine and it’s still not working. I also tried using a different outlet in the house. I’ve waited 24 hours thinking maybe it might have been just the vacuum over heating, but it’s still not working.
ANSWER : I had the same problem and after removing the large round filter and cleaning it, (waiting 12 hrs to dry) it started….
Read Full Q/A … : Eureka 431A Optima Bagless Upright Vacuum
