Euroflex Ez1 Monster Floor Steamer – Cleans & Sanitizes\015 The green light will go on when the steamer is ready. I can hear the steam. As soon as I start lowering the handle to clean, there is a click and the green light goes off then the monster stops steaming. It's very frustrating. This happens right away, before I have even cleaned anything.\015
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
First, check to make sure the unit is plugged in and is in a working outlet. Next, check to make sure there is water in the tank. It is very important to make sure you are ONLY using water to fill the tank. Other solutions may cause breakdown of the gasket and/or other parts of the machine.
I used baking soda to fix the problem. Mix water with a teaspoon of baking soda in a bowl, and then pour the mixture into the water tank (fill up to the brim). Then, turn on the steam and hold the steamer upside down, with the nozzle AWAY FROM YOU. Once the light turns green, turn on the steam.
If your machine turns off automatically again, unplug your machine and remove the nozzle. Hold the tab on the brush roll and spin the other end. Check the drive gear where the brush roll goes into the foot of the machine and remove any debris that may be wrapped in that area. Turn the gear by hand to see if it spins.
Except when you are descaling a steam mop, do NOT put anything other than water in the tank. Not only does this defeat the primary purpose of steam cleaning (in avoiding chemical cleaners), but you can possibly damage your steam cleaner. For many steamers, you may also be voiding your warranty in the process.
Always turn steamers and irons off when you have completed the work. (However, some steamers and irons contain an auto-off option, which will turn off the appliance after a certain amount of time has passed.)
Depending on how you use the steamer, and what pressure setting you choose, steam can last between 1 to 2.5 hours.
We have had some customers who have had their steam cleaners for 5-8 years and are still going strong. For less expensive models like the steam mops or handhelds, you should probably expect more like 3-6 years of consistent use.
Check to see if there is water in the water tank. If there isn`t, unscrew the water tank cap and use the filling flask to pour distilled water into the tank until it reaches the fill line. Replace the water tank cap and tighten. Power the device on, wait about 30 seconds for the water to heat up, and then try again.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
My ez1 Monster Floor Steamer – green light goes off when I lower the handle and stops steaming
ANSWER : It could be calcium deposits in the tank. Clean it with white vinegar. Good luck!
For some reason, our shark steam mop stop working. Usually after I plug the steam mop, the power light would light up then you would hear & see steam coming out of the mop’s head but all of
ANSWER : HEATING ELEMENTS BURNT OUT. WILL COST OVER $100. TOFIX. SHARK NOW HAS A NEW MODEL “SHARK 3” MUCH BETTER
I have a Roomba 560 (it’s still in warranty !!) and, after my summer vacation, it has a problem.
When I’m charging Roomba, the orange light blinks (and this is normal!) but this orange blinking continues forever…. the light doesn’t change to green.
If I detach Roomba from the charger, the light become green and it works normally until the light changes to red and I have to charge it again.
WHY, DURING THE CHARGING PHASE, THE LIGHT DOESN’T CHANGE FROM ORANGE-BLINKING TO GREEN?
HAVE I
ANSWER : The problem is not with the charger itself but it is with the battery inside the Roomba. It sunds like one or more of the cells has gone bad so its not holding the same charge as it did. I would recomend sending it in while the warranty is still valid so they will replace it. Your charger and the Roomba itself should be fine.
A few tips to keep the battery working longer:
Only charge the battery when it is drained all the way to zero. It will help keep the battery active.
Only charge the battery until it is full and then disconect it from the power source. It will keep it active longer plus it will help keep your electric bill down.
Press the power button on – good got a green light (new battery)
press the clean button – got a green light
iRobot runs for a couple of seconds and stops, then starts, then stops. After two or three times I now have a red light on for the Status.
All of the wheels seem to be clean. I used compressed air to clean the underside. But still have the start stop problem.
ANSWER : How many times does the red light blink before it pauses?
My dyson DC05 has been playing up for a while. The motorhead would start fine with green light on and after a few minutes would stop and light would go green. then the power would go on and off – seemed to only work when I had the handle a certain way. Now no power at all. is there a way that I can check if its the power in the handle section as thats the only way you can turn this machine on? Thanks in advance
ANSWER : As the wires that control the motorhead run all the way down the hose it is a break in the wires you will need to buy the hose assy sorry its not thesort of thing you strip down and repair
I broke the handle part of the shark steamer #53101. I don’t have the book to try to tell you the parts I need. Can you send me a picture or a copy of the steamer. It is purple. The above number may not be the correct one. It is broken in the center part. It has a little small circular piece that joins the two pieces which are broken. The beginning of the handle at the bottom of the steamer and the next session which has the steam release. The top of the handle is okay . It the middle and bottom
ANSWER : Hi,
Ann there are very few parts for these…
Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head…
Euro-Pro Shark Steam Mop Problem
Here also is a link to get any of the Shark Manuals that you need.
heatman101
I have an electrolux renaisence vacuum. the brush in the floor attachment turns but I have no suction. When I change to bare floor option on the handle the brush stops turning (correct) but I still have no suction. The lights on the handle showing –floor,carpet, high and low all work.
ANSWER : Sounds like you have a clog, either in the hose or the inlet by the brush roll.
I purchased a Euro-Pro Steamer Mop 9 months ago and the Mop had just quit steaming. The green light is on and it makes a steaming sound but it is not getting hot and does not shoot out any steam like it should. Does it have an element or something that has gone bad in such a short time???
ANSWER : Hi,
Yeah, element is bad…
Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head…
Euro-Pro Shark Steam Mop Problem
Here also is a link to get any of the Shark Manuals that you need.
heatman101
