is not picking up. I have cleaned the hoses and the bottom of the vaccum where the agitator is located. Still it is not picking up dirt. What can i do?
Vacuums

How to Identify and Fix Common Vacuum Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :

Blockage – when a vacuum cleaner becomes unusually loud, it is normally because of a blockage of some sort. This is a problem that is easily solved by turning off the cleaner, check for blockages in the pipes, and remove them. You can also check and empty the canister to remove any possible blockages there as well.
Check for a plugged hose:

Plugged vacuum hoses are sometimes the reason for a loss in suction. Hoses can get clogged with hair, dust bunnies, string, or anything else that can`t pass through the other end of the hose. Airways inside the machine should be looked at as well. Wherever there is an air passage, check it.

Sound enclosures, noise reduction blankets, sound curtain noise barriers, or sound barrier walls are a few options to consider when reviewing noise reduction materials. If the vacuum pump is indoors, a noise enclosure would be the recommended solution.
Hissing or Suction Noises

Another sign that a vacuum hose is leaking in your engine is strange sounds. Specifically, you may hear hissing, squealing, or suction. The volume of the noise depends on how bad the leak is. For example, if you have a minor vacuum leak, you may not hear the hissing at all.

Vacuum cleaners use an electric motor that spins a fan, sucking in air – and any small particles caught up in it – and pushing it out the other side, into a bag or a canister, to create the negative pressure.
Related Articles. Suction generated by a fan motor powers a vacuum cleaner as it pulls dirt through a chamber or hose and then deposits the debris into a bag or a cup. Some vacuum cleaners have a rotating brush or a beater bar at the end of a nozzle to help agitate and sweep dirt into the suction chamber.
Start the engine and spray

Scope out all the vacuum lines under the hood. Then start the engine and spray each connection with a light stream of water. If a connection sucks in the water, you`ve found your leak. A vacuum leak can cause a rough idle, high rpm, poor gas mileage and even trigger a check-engine light.

This means it is best to choose a vacuum cleaner with a noise output that is less than 70 dB. However, the noise levels of vacuum cleaners fall between 75dB to 85dB. Thus, continuous exposure to such noise levels affect a user`s health while also being a sign and source of inefficiencies in the equipment.
During the propagation of sound, the particles of the medium receive these vibrations and transfer them to the surrounding particles, allowing sound to travel. So what does happen to Sound in a Vacuum? In a vacuum, there are no (or very few) particles that can transfer and carry vibrations, so the sound cannot travel.
Hissing or Sucking Noises

Usually, when the leak isn`t too bad, you will hear hissing noises coming from the engine. This may also sound like whining sounds or whimpering sounds. For more severe vacuum leaks, the noise is sucking or suction, much like a vacuum cleaner.

Typically, a vacuum leak will cause situations like hard starting, rough idle, excessive fuel consumption, and engine codes. You might even be able to hear a leak – sometimes a whooshing or whistling sound can be heard with the engine running.
Again, due to the small particle size of baking soda or freshener product, these can clog the pores of your vacuum`s bag or HEPA filter. Or it can “cement” debris into the cyclones of your bagless vac! This can drastically reduce suction resulting in poor cleaning performance and cause clogs to form.
It is obtained by measuring how many inches up a tube the vacuum motor`s intake can pull up, or lift, the water. For the Water Lift test, there is no air moving through the motor. It is a sealed suction measurement to find the pure suction force of the motor.
check for leaks or kinks in the tubing. ensure the filter is not wet (keep a backup filter with your supplies) ensure the float shut-off is not activated (if this is part of your suction machine) check for canister leaks and cracks.
Vacuum suction pressure in adults is 120mmHg.

The lowest vacuum pressure is recommended to reduce the risk of hypoxia and tracheal mucosa injury. However, the pressure has to be strong enough to remove the secretion. Usually, it`s between 80 to 120 mmHg.

If the filter isn`t clean, it can impact the performance of the vacuum. Dirty vacuum filters can restrict airflow so the suction won`t be as strong.
How long do Kenmore vacuums last? A. It`s suggested that the typical vacuum can last up to an average of eight years. With proper maintenance, a Kenmore vacuum could last that long or longer.
Self-propelled vacuums are powered by an electric motor that drives the brush roll. These machines are very useful for people with limited mobility as they can easily maneuver around furniture and other obstacles. Browse the top-ranked list of self-propelled vacuums below along with associated reviews and opinions.
If all you hear from the vacuum unit is a click at the when you try to start the vacuum motor from inside the house, then the motor in the unit is dead and has to be replaced. A strong odor from the shellac, which coats the copper coil windings, is an indicator that the motor is about to or has burnt out.
Generally, the vacuum hoses on your vehicle are made from rubber and are supposed to last for a lifetime. The rough conditions that exist under the hood of your vehicle usually lead to these rubber hoses becoming damaged over time.
If all you hear from the vacuum unit is a click at the when you try to start the vacuum motor from inside the house, then the motor in the unit is dead and has to be replaced. A strong odor from the shellac, which coats the copper coil windings, is an indicator that the motor is about to or has burnt out.
If all you hear from the vacuum unit is a click at the when you try to start the vacuum motor from inside the house, then the motor in the unit is dead and has to be replaced. A strong odor from the shellac, which coats the copper coil windings, is an indicator that the motor is about to or has burnt out.
Vacuum cleaner motors can sometimes start making noises of either a dull or piercing kind. Dull sounds can be caused by hair or pieces of string getting wrapped around the impeller, preventing the motor from turning properly. Piercing noises are normally associated with worn motor bearings.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Bad Motor I have purchased two of the Kenmore direct drive beltless systems with Progressive systems. The first died after a year, the vacuum motor start making a grinding noies. I pulled the side HEPA filter and could see a fine coating of graphite like dust. Took it to a vacuum repair shop. They said the brushes were going and thus the motor was shot. I liked the vacuum and bought a second, 1 year later the motor is making a slight noise that and removing the HEPA filter I find a slight metall
ANSWER : That dust is from the carbon brushes on the motor. You may need to check them, and also clean out the motor compartment. A slight noise could be a motor bearing starting to go. Does the smell like rubber or electrical. If rubber, then the belt has stretched and needs to replaced. If electrical, then something is causing the motor to run hot, like a clogged filter, or it could be a motor going bad.

Read Full Q/A … : Vacuums

I HAVE A BISSELL PROHEAT CARPET CLEANER I DISSEMBLY IT TO CLEAN IT. I DON’T KNOW IF I PUT THE HOSES BACK IN THE RIGHT LOCATION BECAUSE AFTER I PUT IT BACK TOGETHER IT’S LEAKING WATER ALL OVER THE FLOOR BUT IT WILL RECOVER THE WATER FROM THE FLOOR AND THE SOLUTION WON’T SPARY OUT I THINK THE HOSES ARE NOT IN THEIR RIGHT LOCATION TO STOP THE FLOW WHEN IT’S NOT SUPPOSE TO BE COMING OUT CONSTANTLY HELP PLEASE IS THEIR A HOSE DIAGRAM FOR THE HOSES INSIDE THE CARPET CLEANER
ANSWER : Hi,

Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.

Bissell Proheat Upright Wet/Dry Vacuum Problems

heatman101 .
.dygj

Read Full Q/A … : Vacuums

I HAVE A BISSELL PROHEAT CARPET CLEANER 7920 I DISSEMBLY IT TO CLEAN IT. I DON’T KNOW IF I PUT THE HOSES BACK IN THE RIGHT LOCATION BECAUSE AFTER I PUT IT BACK TOGETHER IT’S LEAKING WATER ALL OVER THE FLOOR BUT IT WILL RECOVER THE WATER FROM THE FLOOR AND THE SOLUTION WON’T SPARY OUT I THINK THE HOSES ARE NOT IN THEIR RIGHT LOCATION TO STOP THE FLOW WHEN IT’S NOT SUPPOSE TO BE COMING OUT CONSTANTLY HELP PLEASE IS THEIR A HOSE DIAGRAM FOR THE HOSES INSIDE THE CARPET CLEANER
ANSWER : Hi,

Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.

Bissell Proheat Upright Wet/Dry Vacuum Problems

heatman101 .
.dfjddj

Read Full Q/A … : Vacuums

I have a DC07 and the brush wasn’t rotating and I had no suction at the brush but perfect suction through the hose. I noticed a large build up of dog hair around the brush so I took off the cover plate and removed all the hair, cleaned inside the floor/brush housing and cleaned out the hose. I also cleaned the filter and removed the other air access cover and made sure that they were clear. I put everything back and the brush still doesn’t turn and there is still no suction through the bottom
ANSWER : Hi and welcome to FixYa. I am Kelly.
.
.Here is a link that can assist you in your quest for the missing suction:
.
.http://www.ehow.com/how_4779428_troubleshoot-dyson-vacuum.html
.
.Also Dyson has very good info on cleaning here:
.
.http://www.dyson.com/support/help.asp?article=38&product=DC07-SY-HEPA_US
. (you have to keep clicking next…)
.
.When you get to the part where it asks “is brush head turning?” that you say No. The site is a bit lethargic but should help you get going properly again
.
.Hopefully you find “Airway inspection” as part of your on-line step by step troubleshooting.
.
.If you still have the problem after following the steps above reply / post here and we can proceed from there.
.
. Kelly
.
.
.
.

Read Full Q/A … : Vacuums

HEPA Filter My vacuum came with a sponge over the filter and the directions said I could wash the filter. Do the directions mean to wash the black sponge or the actual filter? Is the sponge part of the filter or is it trash? Filter F27 Dirt Devil Purpose Cleaner for Pets Upright Bagless Vacuum Model #1LY2108-000
ANSWER : Http://geeksquad.fixya.com/ThreadView.aspx?prdid=618630&thid=730623
.HEPA Filter
.Posted by jenski66 on Jul 02, 2008
.My vacuum came with a sponge over the filter and the directions said I could wash the filter. Do the directions mean to wash the black sponge or the actual filter? Is the sponge part of the filter or is it trash?
Filter F27
Dirt Devil Purpose Cleaner for Pets
Upright Bagless Vacuum
Model #1LY2108-000

.
.Hello,
I would advise you to ALWAYS to FIRST UNPLUG YOUR VACUUM before beginning any service procedure. Typically the top filter of which is the sponge is washable but the HEPA filter is not, it can be brushed off and vacuum off with another vacuum, but the best filtration is to replace the HEPA filter and to wash the sponge filter, if the sponge filter get to bad then replace the sponge filter as well. Or, you can check with your local vacuum cleaner dealer in your area or to contact the manufacturer’s website and or phone #. So if you need further assistance, please feel free to contact your local vacuum cleaner dealer in your area or in the yellow pages, or contact the factory phone number or website to further assist you with your questions.

.http://royalvacuums.com/ Customer Service 1-800-321-1134
.Hours are: 8:00 AM to 7:00 PM (EST)
.Thanks, Don the Vac Man
Go Ahead. Use Us.

Read Full Q/A … : Vacuums

My dyson d14 animal keeps cutting in and out. When it’s on, the hole above where the filter is, keeps making a loud suction noise and it won’t clean up hair and dirt.
ANSWER : Vacuum Cleaners require AIr-Flow. Your machine is not getting any air-flow. The noise you hear is a valve opening up to prevent your machine from overheating and burning out the motor.
You probably have an obstruction somewhere in the machine. Dysons are kind of known for that in the vacuum cleaner world.
Check all air channels and clean them out. If that fixes the problem you still might have issues that caused it to clog up.

I posted the part second because it takes 24 hours to complete it.
Be sure you wash your Washable Pre-filter. It needs to dry for 24 hours. Never put it back in the machine wet.

Once it is completely dry reinstall the pre-filter and your machine should be back to normal operating functions.

Let me know f this helps.

Read Full Q/A … : Vacuums

I have the upright kenmore progressive with direct drive and the filter canister stops bringing in air and picking up when hose is put into vaccum, when you remove hose and use as an attachment it starts again
ANSWER : Check the hose after the brushes. With this problem there is normally a clog in between where you disconnect the hose (to use attachment) and the brushes that clean the carpet.

Read Full Q/A … : Vacuums

We have the Kenmore progressive direct drive (bagless) and have had it for about 3 years. We have taken good care of it, and paid quite a bit for it hoping that it would last for a good long time. It has started making a noise that seems to be an overflow air type of noise coming out of a bottom air outlet opening for when the air flow is blocked. We have looked into clogs, changed filters, and the whole works, to no avail! Quite Frustrating since I love this purple vacuum! The machine started
ANSWER : There has to be a clog or block somewhere – if the motor works, it should work did you try a wire coat hanger to go up in further where you cannot see?

Bets regards
Ck

Read Full Q/A … : Vacuums