Kenmore Vacuums\015 My Kenmore Progressive Vacuum canister model 116.25812 was given to me because the canister motor doesn’t turn off unless unplugged. When I turn off the handle switch to the off position, the powerhead will power off but not the canister. I replaced the PCB but no help there. Any ideas? Is this normal??\015
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
Check service panel for tripped breakers/blown fuses. If breaker is tripped, reset it. If fuse is blown, replace it. If vacuum cleaner is plugged in, be sure power button is in the off position before resetting breaker/changing fuse.
Remove the brushroll and clean all hair, string, and lint from the brushroll bearings. If the vacuum cleaner brush still doesn`t spin after you clean the brushroll, consider replacing the brushroll.
Why won`t my power unit shut off? Make sure the unit is in the Auto mode and that there is not a hose plugged into a wall valve. Unplug the low volt wire at the side of the unit, if the unit continues to run, the relay in the pc board is faulty and the entire pc board needs to be replaced.
A Central Vacuum relay or contractor is an electrically operated switch assembly that allows the Central Vacuum to turn on or off by completing the circuit and sending power directly to the central vacuums motor.
This overload reset switch button (part number 8191505) is for vacuums. Overload reset switch button 8191505 resets the overload switch when you push it. Unplug the vacuum before installing this part. Wear work gloves to protect your hands.
If your vacuum cleaner has lost suction power, it`s time to empty the container. Vacuum cleaners come with various foam or mesh filters. These might get clogged over time if not cleaned or replaced properly. This will cause your vacuum to lose suction.
When a central vacuum continues to run without a hose plugged into a vacuum wall port then there is a short in the system. Be sure to unplug the central vacuum unit to stop the vacuum from running and then follow these steps to determine where the short is and what to do about it.
A vacuum cleaner can run continuously for 30 – 60 min each time. The vacuum cleaner has no suction power. For example, a hair cannot be sucked up.
While different factors affect how long a system lasts, many central vacuums can last 20-30 years, or even longer, depending on how often they are used.
Description. Actuator which pulls the throttle mechanism to obtain increased engine speed. The actuator is vacuum operated.
A canister vacuum consists of a wheeled body that is attached to a vacuum wand and power head via a flexible plastic hose. The canister portion of the vacuum contains the main motor, filter, and any dust bags; depending on the model, the power head may also contain a smaller motor.
The better the filtration, the fewer allergens escape back into your home. Bagged vacuums often have HEPA-rated bags, replaceable exhaust filters or both. Bagless canisters usually have permanent, washable filters, some with HEPA ratings.
Dump the Dust
If your vacuum has a disposable bag, remove and discard it. For vacuums that use a plastic canister, remove the bin and dump the contents in the trash. Disassemble as much of the dust cup as possible for easier and more thorough cleaning.
Firstly take it outside, as far away from the door and path as you can, or near or into the wheelie bin. Empty the contents into a plastic bag. Dispose in the outside bin. Use a soft brush of any kind and clean the cylinder casing inside and out.
How long do Kenmore vacuums last? A. It`s suggested that the typical vacuum can last up to an average of eight years. With proper maintenance, a Kenmore vacuum could last that long or longer.
Cause 2: Machine Needs To Be Reset
Unplug the washing machine and leave it unplugged for at least five minutes. Then, plug in the washing machine and try to use it, again.
– Some vacuums have an in-line thermal fuse (often located between the switch lead and the motor coil). If the fuse is blown it will need to be replaced. – Check your home circuit breaker – it may have tripped. – Some vacuums have a brushroll on/off control.
Factors may include having a bad motor, incompatible pump applications or poor ventilation. Constant overheating may indicate a malfunction.
The roller brush is the combination of a belt, a roller, and sometimes a small vacuum head motor. The roller spins, and the bristles attached to it sweep up debris that then gets sucked into the dirt container of the vacuum. The brush head also helps to pull dirt and debris out of carpets of various pile heights.
1. Motorized Brush Head. Sometimes called the “power nozzle,” this large attachment has a rotating brush to clean carpets more like an upright.
Check that the vacuum cleaner is plugged into a working power outlet and that fuses and breakers don`t need resetting. An activated thermal cut-out due to a blockage is the next most likely cause of the problem. Check for blockages in the hose and filters, and remove any obstructions that you find.
With excessive use and regular exposure to dust and dirt, the filters attached to the vacuum cleaner get grime on them. This dusty layer closes the way for air to pass through the channel. Thus, the machine puts a lot of effort and generates noise in excess to pass the air throughout the system.
Why won`t my power unit shut off? Make sure the unit is in the Auto mode and that there is not a hose plugged into a wall valve. Unplug the low volt wire at the side of the unit, if the unit continues to run, the relay in the pc board is faulty and the entire pc board needs to be replaced.
Problems can occur when overused or clogged filters cause the vacuum motor to overheat. This not only shortens the motor life but causes a loss of suction. In some cases, total motor burn out can occur.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
I had the vacuum cleaner question about the canister and the wand/powerhead… the Kenmore Progressive Vacuum canister model 116.25812 and the canister not powering off without unplugging the vacuum. The solution I received that they both run on their own switch so it is normal makes sense. However, is there a power switch on the canister anywhere? The only way for the canister to be turned off is by unplugging it. Any ideas? One would think there would be a switch. I am new to fixya and hope
ANSWER : Hi. On some models, one switch controls all of the power. Your issue, which is no working switch is almost certainly a blown triac on the circuit board in the canister – kenmore part number KC86WBZRZ000
.Take it to your local vacuum repair shop and they should be able to fix it for a nominal fee.
Looks like a common fault with this particular model judging by the number of complaints on the web.
.Take it to your local vacuum repair shop and they should be able to fix it for a nominal fee.
Read Full Q/A … : Kenmore Vacuums
My Kenmore Progressive Vacuum canister won’t turn off.
ANSWER : The two run on there separate switches. so notrhing is wrong with it
Read Full Q/A … : Kenmore Vacuums
Kenmore Progressive canister model 116.27514700
Problem: Vacuum motor won’t turn on. The power head operates, but nothing from the vacuum. Have checked all areas of airflow: hose, bag, motor filter and hepa filter. All are fine. Have checked and rechecked all electrical connections, all seem to be in working order. Vacuum hasn’t run for a week or so, so it’s not the thermal protector, unless it’s defective. Vacuum was running fine last week. Didn’t stop operating when using. Went to v
Problem: Vacuum motor won’t turn on. The power head operates, but nothing from the vacuum. Have checked all areas of airflow: hose, bag, motor filter and hepa filter. All are fine. Have checked and rechecked all electrical connections, all seem to be in working order. Vacuum hasn’t run for a week or so, so it’s not the thermal protector, unless it’s defective. Vacuum was running fine last week. Didn’t stop operating when using. Went to v
ANSWER : Hello! The culprit is the PCB Assembly;
Part # KC86WBZR3000…Cost is $6.99. I would remove and inspect for burnt components, or broken wires…Then clean connections both male/female using an eraser, toothbrush and alcohol…Using a bright light and a magnifying glass inspect solder joints for “bridges” or cold joints. If you detect a problem during this procedure (to the exclusion of burnt components) fix, reassemble, and test. If problem still persist: Order a new part.
Part # KC86WBZR3000…Cost is $6.99. I would remove and inspect for burnt components, or broken wires…Then clean connections both male/female using an eraser, toothbrush and alcohol…Using a bright light and a magnifying glass inspect solder joints for “bridges” or cold joints. If you detect a problem during this procedure (to the exclusion of burnt components) fix, reassemble, and test. If problem still persist: Order a new part.
if you have any question feel free to send a comment.
Guru……………..saailer
Read Full Q/A … : Kenmore Vacuums
Infinity Vaccum by Shark, model number NV31COS, will not start. The vacuum was running just fine until it grabbed the edge of a curtain. Turned it off to release the suction. Turned it back on and was working fine. About a minute later the vacuum was making an odd noise. Every 2 seconds or so it would “heave” (lack of a better word) then go away, then come back and so on. Turned the vacuum off and checked for blockage, none that could be seen or felt, and now the vacuum won’t turn. Any suggestio
ANSWER : Carpet brush won’t turn when vac on
Read Full Q/A … : Kenmore Vacuums
Kenmore 21875 One day it’s working fine. Next day, it won’t turn on. When I attach the hose to another vacuum cleaner, it runs. Is there a reset button on the canister? Could it be the receptacle is bad?
My Kenmore Progressive won’t turn on today either -but was fine last week. I cleaned the filters checked for blocked air, tried a different outlet and no luck. I’ll check the pins on the connections and see if one of them is not matching up or appears worn.
My Kenmore Progressive won’t turn on today either -but was fine last week. I cleaned the filters checked for blocked air, tried a different outlet and no luck. I’ll check the pins on the connections and see if one of them is not matching up or appears worn.
ANSWER : Give the prongs a wiggle and see if there is any play in them.Might just be a plug end.
Read Full Q/A … : Kenmore Vacuums
When we turn on the vacuum, the canister falls open. The clips holding the canister in place do not seem to hold the canister tightly which I’m sure that it did in the past. The clips do not look bent, but every time we turn on the vacuum the intense pressure blows the canister open only remaining attached the the rest of the vacuum by one clip
ANSWER : Check filter and make sure it is kept clean at regular intervals. Possibly worn out clip retainers on cannister side due to excessive pressure build up. Do not force closure unless pressure is back to normal. May crack cannister or damage unit beyond repair.
Read Full Q/A … : Kenmore Vacuums
25512/ 25513 Progressive Canister Vacuum: HI, we have a kenmore progressive canister vacuum …
ANSWER : Cord bad at male prongs, or fuse near motor blown.
Read Full Q/A … : Kenmore Vacuums
I have a Kenmore canister vacuum – model 25614506. Some time ago, I was not able to turn the vacuum off with the on/off switch, but could still use the vacuum. Turned if off/on by pulling the plug. The other day when I went to plug it in, I heard a pop. Now the sweeper runs but the vacuum cleaner does not **** – no air flow. What could be the problem. The cleaner is only 4 years old.
ANSWER : The motor has an inline fuse
Read Full Q/A … : Kenmore Vacuums
