Vacuums\015 Filters clean, bag not full, power point working\015
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
Overheated Motor
If your vacuum was working fine and then suddenly shut off, it may have overheated. Most vacuums are equipped with a thermal protector safety switch that won`t allow the motor to run when it becomes overheated. You will need to wait for 30 minutes to 2 hours, depending on your machine, to try again.
If your vacuum cleaner keeps turning off, this could be due to the following reasons: Blockages – check the hose and head for any obstructions. Filter – always check your filters, if these are clogged this could be causing the vacuum cleaner to work harder and lose suction power.
A strong odor from the shellac that coats the copper coil windings is an indicator that the motor is about to or has burnt out. If the motor is still running, even if it turns on and off by itself as it is heating and cooling, you can still run the motor until it gives up for good.
If your vacuum always trips the breaker, you most likely have an actual electrical problem. Signs that indicate your AFCI breaker is tripping due to an electrical problem include: Frayed cords. If your vacuum cords are old, frayed or deteriorating, it could be producing dangerous electrical arcing.
A thermal cut off is a heat-sensitive device that automatically disconnects the power to a vacuum`s motor when the operating temperature exceeds a safe value.
– Some vacuums have an in-line thermal fuse (often located between the switch lead and the motor coil). If the fuse is blown it will need to be replaced. – Check your home circuit breaker – it may have tripped. – Some vacuums have a brushroll on/off control.
The most common problem with a vacuum cleaner is also the easiest to remedy: clogs in the hose or attachments. Also the electrical cord, motor, switch, fan, brushes, and motor bearings can all need repair or replacement. The drive belt may need replacing; and the attachments, hoses, and filters may need unclogging.
There are varying degrees of quality and value when it comes to vacuums; if you paid a lot for the appliance, repairs are likely worth it, but we recommend that you don`t spend more than half of the original price for any repairs.
Vacuum System Failures:
Reduces or eliminates effectiveness of the turn coordinator, attitude indicator, and heading indicator. Discovered by a low indication on the vacuum gauge or unusual instrument indicators. When the primary air inlet is blocked, the backup inlet automatically opens due to pressure.
Problems can occur when overused or clogged filters cause the vacuum motor to overheat. This not only shortens the motor life but causes a loss of suction. In some cases, total motor burn out can occur.
Overloaded circuits, short circuits and ground faults are all legitimate reasons why your fuses blow on a regular basis or causes for your fuse box to trip out. Other causes could be a result or ageing or faulty wiring as well as power surges.
Overloaded Circuit
The most common cause of a blown fuse we see as experienced Electricians in Sheffield is when something draws too much power from the circuit. This is most often caused by either too many lights or from using too many plug-in appliances at once.
Once all of the checks have been done allow the cleaner to cool down which is usually around 45 minutes. Once its cooled down and plugged back in it should start to work again as the cut out is designed to automatically reset.
Yes, as long as there is no safety hazard associated with continuous operation. In fact, it may be necessary to do so to pump down the base pressure.
A thermal cut off is a heat-sensitive device that automatically disconnects the power to a vacuum`s motor when the operating temperature exceeds a safe value.
Besides getting jammed with dirt and debris, the major problem that cordless vacuums face is a weak battery or failing recharger. Some cordless vacuum batteries are easily replaced while others are not and require that the entire unit be replaced.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
Dirt devil vacuum cleaner–trouble vacuuming dirt and pet hair on carpeting –is the problem with the spinning brush which contacts the floor, not contacting the carpeting?? I thought (when I bought this vacuum) that the aforementioned brush was adjustable to various heights of carpeting. Sometimes, it seems like nothing is being vacuumed up –unless I have just put a new bag on the vacuum… Do I need or can I replace the spinning brush on the bottom of the vacuum so it kicks up and vacuums
ANSWER : Try replacing the belt. Rubber belts stretch out after about a year.
Read Full Q/A … : Vacuums
I purchased a brand new Eureka Pet vacuum, sorry don’t know exact name but it the one that has the self cleaning duster on it. Last night I used the vacuum on my carpet, it was working fine until I accidently sucked up the corner of a scarf that was hanging off a couch. I shut the vacuum off, pulled out the scarf and and resumed vacuuming. Much to my dismay the suction on the vacuum had ceased. Can you tell me if there is a reset button on the vacuum? The vacuum does not appear to be damage
ANSWER : If the motor is running, there should be suction. Possible problems depend on whether it’s a canister or upright and are:
.A clog in the hose, UR or canister. Detach hose. Drop small coin in one end and lift hose causing it to roll out the other. If it does, no clog in hose. Drop same coin into hose opening on power head. If it rolls out, no clog in PN.
.Broken fan blades, UR. Needs to be taken to shop for repair/replacement.
.
.A reset button is for use if the motor isn’t running, so won’t have anything to do with the suction.
.A clog in the hose, UR or canister. Detach hose. Drop small coin in one end and lift hose causing it to roll out the other. If it does, no clog in hose. Drop same coin into hose opening on power head. If it rolls out, no clog in PN.
.Broken fan blades, UR. Needs to be taken to shop for repair/replacement.
.
.A reset button is for use if the motor isn’t running, so won’t have anything to do with the suction.
Read Full Q/A … : Vacuums
The original belt on my upright Kenmore Progressive broke and I replaced it with the spare that was in the vacuum. The vacuum and spare belt are about 10 years old. Then the spare broke after one vacuuming session and there was a burning smell coming from the vacuum. I ordered new belts and replaced it with the new belt. It seems to be working fine with no smell. I checked the belt after I vacuumed the family room and although it was in tact, the belt was very hot. Is that normal? Should t
ANSWER : The belt heats up due to the friction, as well as being in contact with the shaft of a hot motor. It is normal.
Read Full Q/A … : Vacuums
Unbeknownst to me, someone took the bag out of my Kenmore Progressive vacuum and failed to replace it. I have been vacuuming without a bag for months, and today the vacuum stopped sucking. When I opened up the front to replace the bag, tons of dirt and dust came pouring out. I thoroughly cleaned the vacuum, put in a new bag, but still no sucking power. Just dust coming from the rear vents where one of the filters is. Is the vacuum ruined, or is it a simple solution of buying a new filter?
ANSWER : Sounds like you need to buy a new motor. All that grit and dust will ruin a motor and I’m surprised it lasted as long as it did.
.This is where a vacuum that won’t run without a bag would have been nice. (Aerus for one)
.This is where a vacuum that won’t run without a bag would have been nice. (Aerus for one)
Read Full Q/A … : Vacuums
Replacement Motor for a Miele S143 Vacuum Cleaner
ANSWER : Your vacuum should still be under warranty. If they dealer does not fix it for free call Miele directly.
Read Full Q/A … : Vacuums
My vacuum died. It won’t turn on. It is not the outlet. Is it a blown fuse? How do I replace the fuse? Where does it go? This vacuum is a little over 2 years old. My older Hoover WindTunnel STILL works and has never had this problem.
ANSWER : It’s probably the power switch. My switch was dicey for a couple years, finally gave out. Easy to replace.
.
.Remove the two screws just above the WARNING on the rear of the upper handle assembly, then slide the whole assembly to the rear of the vacuum.
.
.Remove the dust bag cover. You will see two holes just above the upper corners of the dust bag. Remove the screws from these recessed screw holes.
.
.Open the furniture cleaner cover and remove the cleaner attachment. Remove the single screw that was hidden behind the attachment. Then remove the attachment housing by pulling it towards the front of the vacuum.
.
.Inside you will see the rear of the power switch. Pull off the power wires (don’t worry, easy on/off male/female connectors, no soldering).
.
.The switch is held in by tension bars at the upper and lower rear of the switch. Firmly press down on one of both of the upper/lower tension bars, and push the switch through the housing from the rear of the switch.
.
.Replacement part number is 28161067, about $2.50. Shop will charge about $85 to repair it themselves.
.
.Remove the two screws just above the WARNING on the rear of the upper handle assembly, then slide the whole assembly to the rear of the vacuum.
.
.Remove the dust bag cover. You will see two holes just above the upper corners of the dust bag. Remove the screws from these recessed screw holes.
.
.Open the furniture cleaner cover and remove the cleaner attachment. Remove the single screw that was hidden behind the attachment. Then remove the attachment housing by pulling it towards the front of the vacuum.
.
.Inside you will see the rear of the power switch. Pull off the power wires (don’t worry, easy on/off male/female connectors, no soldering).
.
.The switch is held in by tension bars at the upper and lower rear of the switch. Firmly press down on one of both of the upper/lower tension bars, and push the switch through the housing from the rear of the switch.
.
.Replacement part number is 28161067, about $2.50. Shop will charge about $85 to repair it themselves.
Read Full Q/A … : Vacuums
Won’t start. My son was using the vacuum & Didn’t change the bag. The vacuum was making the full bag smell, but the light was’t on & it didn’t stop. I stopped him, changed the bag, checked the filter, closed the compartments & turned on the vacuum. Nothing happened. I checked to be sure that it was plugged in, that wasn’t the problem. I’ve let the vacuum “rest” for several days, It still won’t start. Any suggestions?
ANSWER : There is a reset button at the back of the powerhead. The user manual can be downloaded from the electrolux website, although I didn’t find it very useful. There was some info on how to change the powerhead drive belt.
Read Full Q/A … : Vacuums
I have a Kenmore canister vacuum – model 25614506. Some time ago, I was not able to turn the vacuum off with the on/off switch, but could still use the vacuum. Turned if off/on by pulling the plug. The other day when I went to plug it in, I heard a pop. Now the sweeper runs but the vacuum cleaner does not **** – no air flow. What could be the problem. The cleaner is only 4 years old.
ANSWER : The motor has an inline fuse
Read Full Q/A … : Vacuums
