Bissell SpotBot Robotic Wet/Dry Vacuum
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
A possible cause might be that the tank is not properly seated. To assure the tank is seated properly, pick it up and re-seat is so it sits snugly on the unit. If this doesn`t fix the problem, make sure the tank is assembled properly. To make sure they are both latched properly, pick the tank up by its handle.
Check your hose for any cracks or holes that can cause loss of suction. You may also have a clog in the lower hose. Pull down and at an angle to disconnect. A clog in the main hose could also be the problem.
Make sure the Clean Water Tank is seated correctly on the machine. If it isn`t, turn off and unplug your machine, remove and reseat the tank until it clicks into place. This is also a good time to check for cracks or leaks in the tank. If it`s damaged, a replacement can be ordered on BISSELL.com.
Check to see if your clean water tank is empty. The clean water tank also may not be seated properly. If this is the case, turn OFF your machine and re-seat the tank until it clicks into place. Also try priming the system by holding the spray trigger down for 10-15 seconds.
Clogged Automatic Cleaner
Unplug device, remove tanks and flip it over. Check the clear plastic floor nozzles for debris. If they are dirty, unscrew the two screws next to them to remove the nozzle and clean with warm water. Check the suction holes where the nozzles were for any debris and clean them out.
To remove the tank, lift up the dirty tank latch and pull the tank out. Dump out the dirty water and rinse out the tank. Dump out any remaining water/solution from the clean tank and rinse out before storing. Re-place the tank in the unit.
Just Hot Tap Water
You can always clean up most of the mess with hot tap water. Then come back later with the proper Bissell cleaner, if needed.
Bissell Crosswave Pet Pro All in One Wet Dry Vacuum Cleaner
A: Yes, you can leave clean formula/water in the tank when not in use.
A: Yes it can be used as a vacuum without water.
Your machine might not be fully primed. To prime the spinwave hold the spray button for 10 to 15 seconds to make sure the solution has flowed to the spray tips. You may not be holding down the spray button long enough, be sure you hold the button down until you have sprayed enough solution.
First, check to make sure the clean tank has water and/or the water & formula mixture in the tank. If your tank is empty, this could be the reason your machine is not spraying. You will need to fill your clean tank again. Reseat the tank and ensure it sits snug on the machine.
Remove the hose wand from the base, and check for a clog in the wand or base. Next, use a long, narrow object such as the crevice tool or a broomstick to clear away obstructions along the length of the hose.
Your dirty water tank may not be secured tightly. Check the rubber tab on the dirty water tank and press firmly on all edges to secure it tightly. The accessory hose door also needs to be closed securely. Check the door and make sure it is locked in place.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
I have a Hoover Platinum carpet cleaner, and it has stopped dispensing cleaning agent and water. This model has a separate tank for water and separate tank for shampoo dispensing. It also has a power hand unit that dispenses shampoo. All along the hand unit has continued to dispense shampoo. Symptom #1, the water tank seemed to be taking on shampoo, as it was getting sudsy. Symptom #2 – On wash mode, nothing would come out, on Rinse mode, sudsy water would come out. Later, symptom #3 – not
ANSWER : Somewhere on the outlet is a control tap thats driven by a rubber band and something is up with this control ,best advice here is put it in the boot of the car and take iot to a hoover dealer ,they will do it seconds for you
Read Full Q/A … : Bissell SpotBot Robotic Wet/Dry Vacuum
I have a bissell quickwash 1950-e. I bought it Jan. 2006, and have only used it 8-10 times, I live in a very hard water area, so I though if I put some vinegar in with the cleaning solution it would get rid of any hard water deposits, unfortunatly the solution went lumpy in the tank and stoped spraying out water, I have opened it, hose clean, sprayer not blocked, x at bottom of water container when depresed water trickles out, component that opens the x when water container placed, also ran wate
ANSWER : Hard to say what is causing your problem, replacing the cap and insert on the water tank may help, part #2041111, even tho it may trickle out water when depressed, they can still be bad. The other thing would be the rod not relesing the water like it should. The big draw back to this model is Bissell has obsoleted all of its parts and most are no longer available. Might be wiser to buy new.
Read Full Q/A … : Bissell SpotBot Robotic Wet/Dry Vacuum
I have a Bissell Pro 2x carpet cleaner. The water heats properly as well as spraying the cleaning product. However, when I go to suction the water from the carpets, the 2 in 1 water tank bladder works properly but there is no dirty water outside the bladder. I have only used this carpet cleaner ~ 5 times and in the beginning I had to empty the suctioned water quite frequently as it was dirty and it could not not hold any more water. So I have done 1 room and all the dirt remains in the carpet
ANSWER : Check that the suction cone is not blocked. Check that the filter or hose to the bladder isn’t blocked as well.
Read Full Q/A … : Bissell SpotBot Robotic Wet/Dry Vacuum
The Hoover Steamvac Widepath will NOT pick up water. The dispenser with cleaner DOES have water. The TANK that would receive the dirty water is NOT full. All tanks are on properly and the machine will still not pick up the used water. I found a tear in the interior hose leading to the receiving tank and repaired throughly with electrical tape. Still will not pick up the water. Any suggestions?
ANSWER : Sounds like a clogged air path (no vacuum action) from the floor pick-up to the collection tank. Take the tanks off and deal with the vacuum problem alone. The collection tank should have a air exit vent–is it clear? Check the interior hose that you repaired–is it clogged? Remove the bottom plate and inspect the air path from it. Because this machine deals with water, clogs can become like concrete! Hope this helps!
Read Full Q/A … : Bissell SpotBot Robotic Wet/Dry Vacuum
Water is not dispensing to clean carpet. Water
ANSWER : The problem is the heater is cloged you can drill it out to clean it
Read Full Q/A … : Bissell SpotBot Robotic Wet/Dry Vacuum
I have a Bissell Proheat 2XTurbo carpet cleaner. No water will come out when I squeeze the trigger. I have filled the solution tank and the water tank. I read the troubleshooting in the manual and have tried turning it off for a minute and restarting and nothing. I took out both tanks and reseated them and nothing. It has sat for over a year but did not have any water in the water tank. Some solution was left in the solution tank. How can I make the water come out? HELP!
ANSWER :
Call BISSELL Consumer Services.
.
1-800-237-7691
.
Mon-Fri: 8am to 10pm ET
.
Sat: 9am to 8pm ET
Read Full Q/A … : Bissell SpotBot Robotic Wet/Dry Vacuum
Cleaner will not dispense the water from the tank. It solution is dispensed but not the water from the blatter. It also picks up water from the carpet.
ANSWER : Check hose for a clog
Read Full Q/A … : Bissell SpotBot Robotic Wet/Dry Vacuum
The soap dispenser on my 2X is not dispensing.
I wrote with this initial problem and received a reply. We did everything recommended to find a clog. To begin with, we poked holes thru the little holes on the underside with a toothpick. Next we took the machine all apart as directed and cleaned out anything that had accumulated (such as pet hair). Eventually we emptied out the soap dispenser, filled it with a hot salt water solution and let it sit for 10 min. I ran three tanks of hot water
ANSWER : Hello,
The solution to your problem is already solved, since your soap dispenser is still under warrant,
What i will suggest is that you contact the company that supply you this product and explain everything to them, it is most likely they give you the solution to your problem or send someone to your aid, or can even replace the product for you.
Take care.
Read Full Q/A … : Bissell SpotBot Robotic Wet/Dry Vacuum
