Bissell LiftOff Revolution Pet Vac 37602 Vacuum

How to Identify and Fix Common Vacuum Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :

A possible cause might be that the tank is not properly seated. To assure the tank is seated properly, pick it up and re-seat is so it sits snugly on the unit. If this doesn`t fix the problem, make sure the tank is assembled properly. To make sure they are both latched properly, pick the tank up by its handle.
Check your hose for any cracks or holes that can cause loss of suction. You may also have a clog in the lower hose. Pull down and at an angle to disconnect. A clog in the main hose could also be the problem.
There could be several factors as to why your BISSELL PowerFresh steam mop is not producing steam. First, check to make sure the unit is plugged in and is in a working outlet. Next, check to make sure there is water in the tank. It is very important to make sure you are ONLY using water to fill the tank.
Check the dirty water tank and make sure there are no clogs in the hose below it. Remove the filter and clean debris from both the screen and filter. Also empty the dirty water tank and leave the filter out to dry completely before replacing it.
check the cap of the water tank to make sure it is correctly and securely attached to the water tank. check your water tank to make sure it is securely and correctly fitted in to the body of the garment steamer – incorrect placement of the water tank can block water from feeding in to the body and boiler of the steamer.
There is condensation in the stand steamer`s hose

To solve this, lift your stand steamer`s head to straighten the hose vertically and hold your steamer in an upright position: This will allow any condensation and steam to flow again. After this, your stand steamer should steam again.

Always Uses Clean Water

With the CrossWave Cordless Max however, clean and dirty water is kept in separate tanks so you only add fresh water and cleaning solution to the floor. Dirty water and debris are kept in another tank for easy disposal.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

My steam cleaner wont pick up water i have checked everything and its fine but still isnt sucking up water
ANSWER : Well Sexy mama ..are there any on~board screens that require clearing? Pet hair clogging up vac wand end? Is there vacuum power for attachment hose? Also, check that the wand /attachment switch is to vacuum and not set for attachments. Good luck !

The Hoover Steamvac Widepath will NOT pick up water. The dispenser with cleaner DOES have water. The TANK that would receive the dirty water is NOT full. All tanks are on properly and the machine will still not pick up the used water. I found a tear in the interior hose leading to the receiving tank and repaired throughly with electrical tape. Still will not pick up the water. Any suggestions?
ANSWER : Sounds like a clogged air path (no vacuum action) from the floor pick-up to the collection tank. Take the tanks off and deal with the vacuum problem alone. The collection tank should have a air exit vent–is it clear? Check the interior hose that you repaired–is it clogged? Remove the bottom plate and inspect the air path from it. Because this machine deals with water, clogs can become like concrete! Hope this helps!

I have a Bissell Pro 2x carpet cleaner. The water heats properly as well as spraying the cleaning product. However, when I go to suction the water from the carpets, the 2 in 1 water tank bladder works properly but there is no dirty water outside the bladder. I have only used this carpet cleaner ~ 5 times and in the beginning I had to empty the suctioned water quite frequently as it was dirty and it could not not hold any more water. So I have done 1 room and all the dirt remains in the carpet
ANSWER : Check that the suction cone is not blocked. Check that the filter or hose to the bladder isn’t blocked as well.

Steam cleaner stopped sucking up water. Motor still running. It’s blowing hot air. I checked the seal on the water recovery tank and it appears ok.
ANSWER : Steam vac won’t **** up water

Water is not being discharged. I have filled the reservoir that holds the carpet cleaner fluid And I have filled the water container. I know how to use the cleaner, it has always worked, But now, no water is being discharged to the carpet. I turn it on, squeeze the trigger, but nothing comes out. The wheel that is suppose to spin (to indicate that water is being discharged) is not spinning. Everything else works. I.e. the suction works, and the hand held accessories work.
ANSWER : That means that the pump belt is worn and it needs to be replaced. You can get a replacement belt and view the manual here:

Bissell Pump Belt

Producing steam i just got the shark assembled the mv2010, then it is not doing anything, it vacuumed just fine, but when i put the steam pad on it wouldnt ever produce steam or do anything,it felt like the water was heating up but even after it sat for 20-30 minutes when i pull handle back towards me nothing happens, no lights no steam no nothing, so why wont it work

My filter queen just had the motor rebuilt last year and was basically a brand new unit when I got it back. It is not picking anything up now when I vacuum. The beater bar on the carpet attachment is turning fine and when I take all the attachments off the hose I can feel the suction being created like it should be picking up debris just fine. I have emptied the canister even when it did not have much in it; however, it still will not pick anything up off the carpet. It picks up debris tempo
ANSWER : It sounds as if you have a clog inside the “Power Nozzel”. They mention that there are “no user serviceable parts within the Majestic® Power Nozzle” My advice would be to see if you can see a clog with in reachable distance and try to remove the clog. One way to check for a clog which may work for you is to remove the attachment and shine a flashlight on one of of the attachment and look through the other side and see if you see light, if no light, most likely a clog. Past that you might void the warrenty if you try and open it up the Power Nozzel itself. You may want to ask a Phone service rep about clog removal.

My Bisssil cleaner will not pick up the water from the floor. I checked all the trouble shooter helps and evewrything is OK Checked all belts they are OK. It also will not pick up water with the hand held tools, seems as though the vacuum is not working
ANSWER :

Hi,

Here is a tip that will give you all the information you need to fix your Bissell Proheat Vacuum Problem.

Bissell Proheat Upright Wet/Dry Vacuum Problems

heatman101
.