Bissell 3576 CleanView II Bagless Upright Vacuum

How to Identify and Fix Common Vacuum Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :

Check to make sure the Vacuum Suction Knob is turned towards “Floor Suction.” Or there could be large debris clogging the brush roll rotation. Your dirt container may not be seated properly or may be full. Press the Tank Release button and remove.
If you find that your CleanView vacuum is hard to push, you may need to adjust the height adjustment dial. The highest setting should be used for high pile and most shag carpet.
The suction power indicator tells you when the air flow in your vacuum is reduced due to dirty filters or a clog in the hose. The suction power indicator will remain green until the airflow is reduced.
Related Articles. Suction generated by a fan motor powers a vacuum cleaner as it pulls dirt through a chamber or hose and then deposits the debris into a bag or a cup. Some vacuum cleaners have a rotating brush or a beater bar at the end of a nozzle to help agitate and sweep dirt into the suction chamber.
We have two possible ways of adjusting the pressure in a vacuum system: first, by changing the pumping speed (altering the speed of the pump or throttling by closing a valve); second, through admission of gas (opening a valve).
Loose connections will cause your vacuum cleaner to lose suction. Make sure that the dust container, the hose, the tube and the brush are all attached properly. If the problem continues, your vacuum cleaner might have a technical problem. If you suspect this to be the case, contact an authorised service agent.
In vacuum handling technology and other applications that operate in the rough vacuum range, the vacuum level is typically measured using direct-reading gauges. Direct-reading gauges can provide an accurate measurement from atmospheric pressure down to about 1 Torr and in some cases lower.
Suction pressure is always measured by the amount of pressure below atmospheric pressure e.g. a suction pressure of 100 mbar means 100 mbar below the atmospheric air pressire. Vacuum pressure is similar but should be referred to perfect vacuum e.g. a vacuum of 100 mbar means 100 mbar above a perfect vacuum.
So, the usual areas that cause suction loss include the wrong height setting, stuck rollers, a faulty gasket, a broken vacuum belt, a filled bag, or a clogged hose.
check for leaks or kinks in the tubing. ensure the filter is not wet (keep a backup filter with your supplies) ensure the float shut-off is not activated (if this is part of your suction machine) check for canister leaks and cracks.
If the filter isn`t clean, it can impact the performance of the vacuum. Dirty vacuum filters can restrict airflow so the suction won`t be as strong.
Positive-displacement pumps can operate with lower suction pressures or high suction lifts because they can create stronger vacuums. Suction lift will be greater if the pressure in a closed tank is greater than atmospheric pressure.
Overcharging leads to overfeeding the evaporator with refrigerant, which leads to higher suction pressure. Another possibility is having oversized EXV causes an overfeed to the evaporate, which increases your suction pressure.
There are two separate suctioning techniques, namely the closed and open system. Basic principles of suctioning are the same, and care should be incorporated during suctioning.
If the suction pressure is reduced then the following effect will happen: The refrigeration effect decreases from (h1 – h4) to. The work required by the compressor increases from (h2 – h1) to h`2 – h` Hence the COP decreases on reducing suction pressure.
To clean a foam filter, submerge it in water, squeeze it to allow the dirt to escape the foam, and allow it to air dry before putting it back in your vacuum. If you want the room to smell really nice next time you`re vacuuming, add a few drops of essential oil to the foam.
Again, due to the small particle size of baking soda or freshener product, these can clog the pores of your vacuum`s bag or HEPA filter. Or it can “cement” debris into the cyclones of your bagless vac! This can drastically reduce suction resulting in poor cleaning performance and cause clogs to form.
What is a Good Suction Power for a Vacuum Cleaner? An upright cordless vacuum cleaner should have at least 100 air watts to effectively clean a variety of floor surfaces, with the best Samsung vacuum cleaner reaching up to 210W*.
Locate the brush reset button on the lower back right of the vacuum. Press the button to reset the brushroll To ensure the brush has been reset, plug the vacuum back into the electrical outlet.
Max(4000 PA): It can deeply clean the place that needs cleaning, dust cleaning is up 80%, garbage collection is up 30%, and the cleaning times are up to 80 minutes.
Ultimately though, a suction force of 1000 Pa or more serves as the general rule-of-thumb benchmark for quality vacuuming performance. I did my research to compare the suction power of current vacuum cleaners, from robot vacuums to regular vacuums.
The Vacuum Gauge is a robust and compact device to measure pressure. One field of use of the Vacuum Gauge is, for example, the checking of the input/output of liquefied gas.
One “torr,” a unit named in honor of Torricelli, is equivalent to one millimeter of mercury, yielding the figure of 760 torr as normal atmospheric pressure at sea level. Torr as units of measure are typically used for vacuums in the 1 to 760 Torr range.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

My vacuum tools have very weak suction. – Bissell 3576 CleanView II Bagless Upright Vacuum
ANSWER : There is a foam ring filter in the bottom of the canister that collects the dirt. It screws off of the bottom on the canister. Take outside and shake it out. It fixed our suction problem.

Read Full Q/A … : Bissell 3576 CleanView II Bagless Upright Vacuum

Something lodged in my bissell upright – Bissell 3576 CleanView II Bagless Upright Vacuum
ANSWER : Hey, you may want to have a BISSELL Authorized Service Center inspect your vacuum.

Here’s a quick link to locating one in your area:.

http://www.bissell.com/service-centers/?cid=ccsocial

Read Full Q/A … : Bissell 3576 CleanView II Bagless Upright Vacuum

I purchased a brand new Eureka Pet vacuum, sorry don’t know exact name but it the one that has the self cleaning duster on it. Last night I used the vacuum on my carpet, it was working fine until I accidently sucked up the corner of a scarf that was hanging off a couch. I shut the vacuum off, pulled out the scarf and and resumed vacuuming. Much to my dismay the suction on the vacuum had ceased. Can you tell me if there is a reset button on the vacuum? The vacuum does not appear to be damage
ANSWER : If the motor is running, there should be suction. Possible problems depend on whether it’s a canister or upright and are:
.A clog in the hose, UR or canister. Detach hose. Drop small coin in one end and lift hose causing it to roll out the other. If it does, no clog in hose. Drop same coin into hose opening on power head. If it rolls out, no clog in PN.
.Broken fan blades, UR. Needs to be taken to shop for repair/replacement.
.
.A reset button is for use if the motor isn’t running, so won’t have anything to do with the suction.

Read Full Q/A … : Bissell 3576 CleanView II Bagless Upright Vacuum

Why do the belts keep breaking – Bissell 3576 CleanView II Bagless Upright Vacuum
ANSWER : Hi there,...

Well the problem happens due to the belt If the belt not installed correctly, the rubber belt will grate against one of the components in the roller brush housing. The friction of the belt against the housing produces a pungent burning odor. To correct this you need a right belt, each vacuum cleaner manufacturer produces specific belts for specific machines. An incompatible belt installed on the vacuum cleaner will cause the belt to break or burn.

Good Luck!!

Thanks for using FixYa!!

Read Full Q/A … : Bissell 3576 CleanView II Bagless Upright Vacuum

Power is on (light works) but no motor – Bissell 3576 CleanView II Bagless Upright Vacuum
ANSWER : Hi Marjorie! I know how frustrating this must be. You may want to have your vacuum inspected by one of our Authorized Service Centers.

Here’s a quick link to help you locate one in your area:.

http://www.bissell.com/service-centers/?cid=ccsocial

Read Full Q/A … : Bissell 3576 CleanView II Bagless Upright Vacuum

Bissell vacuum roller will not spin – Bissell CleanView II Plus Upright Bagless VacuumVacuum
ANSWER : HI,
.Most of the time if the roller will not turn it is because the belt is either strecthed too far and is loose or it is completely broken…
.Check and replace the belt before doing anything else.
.
.heatman101

Read Full Q/A … : Bissell 3576 CleanView II Bagless Upright Vacuum

Dirt devil vacuum cleaner–trouble vacuuming dirt and pet hair on carpeting –is the problem with the spinning brush which contacts the floor,  not contacting the carpeting??  I thought (when I bought this vacuum) that the aforementioned brush was adjustable to various heights of carpeting.  Sometimes, it seems like nothing is being vacuumed up –unless I have just put a new bag on the vacuum… Do I need or can I replace the spinning brush on the bottom of the vacuum so it kicks up and vacuums
ANSWER : Try replacing the belt. Rubber belts stretch out after about a year.

Read Full Q/A … : Bissell 3576 CleanView II Bagless Upright Vacuum

Bissell cleanview vacuum poor suction
ANSWER : The next thing that you need to do is replace the belt. Even if it’s not cracked or worn, many times it’s too loose, and it won’t turn to rotor efficiently.
.
.Believe it or not, just replacing the belt may be all that you need to do!

Read Full Q/A … : Bissell 3576 CleanView II Bagless Upright Vacuum

Hi, my name is Mea Archer, owner of the vacuum cleaner blog, the niche website that I have developed to provide the most up-to-date news, reviews and the latest advice and information for all things vacuum cleaner related.