Vacuums\015 I have a small vacuum that is bag-less, and I need to know if I can wash the filter or if I need to get a new one and where can I get a new filter at and what kind of filter can I get?....Where do I go to get a new filter and what is the name of the filter that I need to get?\015
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
One of the easiest ways to increase vacuum cleaner suction is to empty the dust bag or container. Dust containers need to have enough space for airflow, otherwise, they could get clogged and have less suction power. Regularly check your dust compartment and empty or change it when it`s already 70-80% full.
Vacuum cleaners use an electric motor that spins a fan, sucking in air – and any small particles caught up in it – and pushing it out the other side, into a bag or a canister, to create the negative pressure.
The most common problems found in vacuum cleaners are low suction force, excessive noise, burning smell, vacuum not turn on, and overheating. These issues can be fixed by either cleaning the device or replacing some parts of the device. At times, it is best to seek a professional to fix the cleaner effectively.
Therefore, the more airflow, the better the cleaning ability of the vacuum cleaner. Airflow is an excellent specification because it takes into account both the power of the vacuum motor, which creates suction, as well as the resistance of the bag and filter system that this air must pass through.
So, the usual areas that cause suction loss include the wrong height setting, stuck rollers, a faulty gasket, a broken vacuum belt, a filled bag, or a clogged hose.
Suction Power
The suction capacity indicates how powerful the vacuum cleaner is, and the air volume indicates how much air the vacuum cleaner is able to move. The suction power adds up the suction capacity and the air volume and indicates how much power the vacuum cleaner has.
Vacuum System Failures:
Occurs when the vacuum pump fails or when both intakes are blocked.
Low compression, an intake leak or tight valves also can cause low vacuum at idle. If the vacuum reading fluctuates within the normal range-the gauge needle bounces around a lot-uneven compression (broken rings or leaking valves or head gasket in one or two cylinders) is a likely culprit.
Factors like the amount of suction developed by the suction motor, the amount of resistance in the filtration system as it traps the dirt, the total amount of resistance in all air passages as well as the design of the cleaning nozzle will significantly affect the vacuum cleaner`s ability to pick up the dirt.
Any negative pressure significantly below standard atmospheric pressure (760 Torr/mmHg, 29.9 inHg or 14.7 PSI) is considered a vacuum.
A little bit of water can do wonders for boosting a suction cup`s grip. Using warm water, rinse the whole cup so it softens it up. Shake the drops of water off the cup quickly and then put it up on the wall.
Putting in the incorrect amount of oil, putting in the wrong type of oil, and oil contamination can all cause the pump to not reach full vacuum. For this reason, you must check the oil regularly to ensure that it is not only clean, but also properly filled.
An upright vacuum cleaner should be around 100 air watts and a cylinder vacuum cleaner needs to be about 220 air watts.
Basically, the higher you are, the less vacuum you can attain. Because free air is less dense at higher altitudes (i.e. lower atmospheric pressure) operation at these higher altitudes has the effect of reducing the capacity and maximum vacuum levels attainable.
The Roborock S5 offers 2000Pa of suction power. Pa is short for Pascal Pressure Unit. The higher the number, the higher the suction power. Could you imagine what 2000Pa means? It means that the Roborock S5 has enough suction to pick up AA batteries off your floor.
Air watts refer to the number of watts used by the vacuum cleaner to carry a unit of air through an opening or nozzle. The higher the air watts, the higher the suction power.
Vacuum is primarily measured by its absolute pressure. At room temperature and normal atmospheric pressure, one cubic foot (0.03 cubic m) of air contains approximately 7×1023 molecules moving in random directions and at speeds of around 1,000 miles per hour.
Stainless steel is the preferred material of construction and is used almost exclusively in ultra-high vacuum systems. Austenitic stainless steels 304 and 316 are commonly used while free machining 303 is avoided due to its much higher sulfur content.
If there is a clog in the vacuum, you won`t have good suction and the vacuum won`t work. The clog can be in the vacuum head, the hose or where the hose meets the actual vacuum.
What is a vacuum leak? A vacuum leak is a small hole in one or several parts of the system that allows the uncontrolled entry or exit of gas. The leak rate is dependent on several factors, including the size of the hole, gas type, and the pressure differential (between the inside and the outside of the system).
3) A closed throttle will create more vacuum than an open throttle. As the engine load increases, the throttle will open wider. This will allow for more air and fuel, create more power, and lower the manifold vacuum reading.
If all you hear from the vacuum unit is a click at the when you try to start the vacuum motor from inside the house, then the motor in the unit is dead and has to be replaced. A strong odor from the shellac, which coats the copper coil windings, is an indicator that the motor is about to or has burnt out.
The level you set your vacuum depends on the height of your carpet. For bare floors, use the lowest or bare floor setting, for short and medium pile carpets use a medium setting and finally, for plush carpets use the highest setting.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
Dirt devil vacuum cleaner–trouble vacuuming dirt and pet hair on carpeting –is the problem with the spinning brush which contacts the floor, not contacting the carpeting?? I thought (when I bought this vacuum) that the aforementioned brush was adjustable to various heights of carpeting. Sometimes, it seems like nothing is being vacuumed up –unless I have just put a new bag on the vacuum… Do I need or can I replace the spinning brush on the bottom of the vacuum so it kicks up and vacuums
ANSWER : Try replacing the belt. Rubber belts stretch out after about a year.
Read Full Q/A … : Vacuums
I purchased a brand new Eureka Pet vacuum, sorry don’t know exact name but it the one that has the self cleaning duster on it. Last night I used the vacuum on my carpet, it was working fine until I accidently sucked up the corner of a scarf that was hanging off a couch. I shut the vacuum off, pulled out the scarf and and resumed vacuuming. Much to my dismay the suction on the vacuum had ceased. Can you tell me if there is a reset button on the vacuum? The vacuum does not appear to be damage
ANSWER : If the motor is running, there should be suction. Possible problems depend on whether it’s a canister or upright and are:
.A clog in the hose, UR or canister. Detach hose. Drop small coin in one end and lift hose causing it to roll out the other. If it does, no clog in hose. Drop same coin into hose opening on power head. If it rolls out, no clog in PN.
.Broken fan blades, UR. Needs to be taken to shop for repair/replacement.
.
.A reset button is for use if the motor isn’t running, so won’t have anything to do with the suction.
.A clog in the hose, UR or canister. Detach hose. Drop small coin in one end and lift hose causing it to roll out the other. If it does, no clog in hose. Drop same coin into hose opening on power head. If it rolls out, no clog in PN.
.Broken fan blades, UR. Needs to be taken to shop for repair/replacement.
.
.A reset button is for use if the motor isn’t running, so won’t have anything to do with the suction.
Read Full Q/A … : Vacuums
I have an Ecectrolux Epic canister vacuum. As soon as it starts sucking, the vacuum cuts off. I put a new filter and bag in, but it doesn’t seem to help. If I open the front where the bag goes, take the bag out and depress the safety button the vacuum will run. Need some help or direction.
Thank you
Thank you
ANSWER : Try this.
.Disconnect hose. Turn machine on and place hand over intake. If it shuts off immediately, first try turning dial on top of machine so largest dot matches up with arrow. Turn on and place hand over intake again. If it still shuts off immediately, the “control valve assembly” is worn or broken and needs replaced. Don’t try this yourself.
.Take your complete machine to the nearest authorized Aerus Electrolux shop, or call and ask someone to pick it up. There’s no extra fee for this, or delivery upon repair.
.The repair/replacement should include a complete cleaning of your vacuum in the labor, but ask the service manager to be sure.
.The shop nearest you can be found by typing your zip code into the indicated space on the site listed below.
.
.http://www.aerushome.com/storelocator/
.Disconnect hose. Turn machine on and place hand over intake. If it shuts off immediately, first try turning dial on top of machine so largest dot matches up with arrow. Turn on and place hand over intake again. If it still shuts off immediately, the “control valve assembly” is worn or broken and needs replaced. Don’t try this yourself.
.Take your complete machine to the nearest authorized Aerus Electrolux shop, or call and ask someone to pick it up. There’s no extra fee for this, or delivery upon repair.
.The repair/replacement should include a complete cleaning of your vacuum in the labor, but ask the service manager to be sure.
.The shop nearest you can be found by typing your zip code into the indicated space on the site listed below.
.
.http://www.aerushome.com/storelocator/
Read Full Q/A … : Vacuums
I have a kenmore progressive direct drive handi mate jr. upright vacuum. My daughter used it last night to vacuum up some cat litter that had spilled on the floor. I went to use it today and it turned on for a second and then stopped working. I have hit the reset button but it will not turn on. Help this vacuum is only 2 years old Is there anything that I need to reset or do so that the vacuum will work again?
ANSWER : Its probably clogged up with cat litter.might have gotten into the motor.your motor has a motor guard inside if it. when it overheats it will shut down till it cools off.you need to clean all th cat liter out of it.and clean the filters.with a direct drive you might want to take it in to a repairman to sevice. its not a shop vac i advise you not to pick up things like cat liter
Read Full Q/A … : Vacuums
I do not have my users manual and have never vacuumed wet with this vacuum. How do I change it from a dry to wet vacuum.
Can’t find my manual and I need to use the shop vac for water in basement, do I have to change the filter or what
lost my user manual never used it to pick up water. need to know how to puit it in wet mode i want to clean the dirty water out of my pool.
Can’t find my manual and I need to use the shop vac for water in basement, do I have to change the filter or what
lost my user manual never used it to pick up water. need to know how to puit it in wet mode i want to clean the dirty water out of my pool.
ANSWER : .Vacuuming Liquids
.1. When picking up small amounts of liquid
.the filter may be left in place.
.2. When picking up large amounts of liquid
.we recommend that the filter be
.removed. If the filter is not removed, it
.will become saturated and misting
.may appear in the exhaust.
.3. After using the vac to pick up liquids,
.the filter must be dried to reduce the
.risk of possible mildew and damage to
.the filter.
.4. When the liquid in the drum reaches a
.predetermined level, the float mechanism
.will rise automatically to cut off
.airflow. When this happens, turn off
.the vac, unplug the power cord, and
.empty the drum. You will know that the
.float has risen because vac airflow
.ceases and the motor noise will
.become higher in pitch, due to
.increased motor speed.
.IMPORTANT: To reduce the risk of damage
.to the vac do not run motor with float
.in raised position
.1. When picking up small amounts of liquid
.the filter may be left in place.
.2. When picking up large amounts of liquid
.we recommend that the filter be
.removed. If the filter is not removed, it
.will become saturated and misting
.may appear in the exhaust.
.3. After using the vac to pick up liquids,
.the filter must be dried to reduce the
.risk of possible mildew and damage to
.the filter.
.4. When the liquid in the drum reaches a
.predetermined level, the float mechanism
.will rise automatically to cut off
.airflow. When this happens, turn off
.the vac, unplug the power cord, and
.empty the drum. You will know that the
.float has risen because vac airflow
.ceases and the motor noise will
.become higher in pitch, due to
.increased motor speed.
.IMPORTANT: To reduce the risk of damage
.to the vac do not run motor with float
.in raised position
Read Full Q/A … : Vacuums
I have a Kirby G4 Vacuum Cleaner – MOdel G4 D. I have never had any problems or repairs done to it in the past ten plus years that I’ve had it. This is an upright vacuum. I was vacuuming the carpet floor and was not having any trouble at all. I switched the vacuum off and moved it into a different room. When I tried to turn on the vacuum, it would not turn on. I checked with different outlets, used both front attachment and hose attachment. Checked the front part of the motor/ spiral case. This
ANSWER : Hello,
.My educated guess is that it’s either the switch or the power cord. Here are a couple of guides to help with diagnosis and repair…
.
.http://reviews.ebay.com/COMMON-PROBLEMS-WITH-THE-KIRBY-VACUUM-TROUBLESHOOTING_W0QQugidZ10000000003800312
.
.http://reviews.ebay.com/REPLACING-THE-POWER-SWITCH-ON-ANY-KIRBY-G-SERIES-VACUUM_W0QQugidZ10000000003752018
.
.Hope this helps!!
.Marci
.My educated guess is that it’s either the switch or the power cord. Here are a couple of guides to help with diagnosis and repair…
.
.http://reviews.ebay.com/COMMON-PROBLEMS-WITH-THE-KIRBY-VACUUM-TROUBLESHOOTING_W0QQugidZ10000000003800312
.
.http://reviews.ebay.com/REPLACING-THE-POWER-SWITCH-ON-ANY-KIRBY-G-SERIES-VACUUM_W0QQugidZ10000000003752018
.
.Hope this helps!!
.Marci
Read Full Q/A … : Vacuums
Suction problem I have a Hoover Widepath Fold Away, 12 amp motor vacuum cleaner and the problem I am having is every time I vacuum, the vacuum gets clogged up with carpet. I am probably only able to do one stroke then it gets clogged and I have to stop and unclog it or it spits it out on the carpet. This is very frustrating and I don’t get much vacuuming done. Please can you help me. Thank you. Gwen email is [email protected]
ANSWER : Get rid of the carpet its shredding and falling apart.no sence in vacuuming old rotten carpet.or try using a vacuum without a brush roller and just suction
Read Full Q/A … : Vacuums
OUR DYSON 07 SWEEPER HAS VERY LITTLE Vacuum, have cleaned all filters and hoses, on line troubleshooting has said to check soleplate being on correctly, we have done this, still does not have good vacuum, belts are covered by a housing, the video that shows the changing of the belt is not the same, I need to know how to remove the cover to check both belts and any help in gaining the vacuum
ANSWER : This video shows you everything you need to know
Read Full Q/A … : Vacuums
