Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
How to use a vacuum cleaner: 7 easy steps
- Step 1: Dust your furniture using a duster. …
- Step 2: Make way for your vacuum cleaner. …
- Step 3: Check the vacuum bag if it`s full. …
- Step 4: Use the recommended nozzle for optimal use. …
- Step 5: Slowly vacuum the area. …
- Step 6: Don`t cut corners. …
- Step 7: Empty the vacuum bag if needed.
Vacuuming should always be followed by wet mopping to eliminate any bonded soils. Wet mopping should also be used on an as-needed basis to clean up spills. Floors are burnished on an interim basis for deeper cleaning.
They are majorly used to remove dirt and dust from upholstery, carpets, velveteen furniture and floors made of hardwood and many varieties of floors, including laminated floors. They are also used to clean cars and stairs.
Yet, the unfortunate truth is that you should never use shampoo or soap to clean your carpet. By using shampoo on carpet, you`re doing damage to the carpet`s fiber. And shampoo leaves a residue that can cause irritation to you and your family members.
Laundry Detergents aren`t Formulated for Carpet Cleaning
Cleaning solutions are specifically formulated to clean and not damage the machines they`re used in and the material they`re treating. Laundry soap is designed to be used in washing machines to clean clothing.
While carpet cleaners are designed to work optimally with carpet shampoos, they will also do the job with a laundry detergent. In fact, this is one of the safest substitutes you can use. Using laundry detergent in a carpet cleaner will provide you with effective results and you won`t even have to use a lot of it.
The nozzle cleaning function works by rinsing the spray nozzle with water before and after a wash cycle. The nozzle will oscillate back and forth when the sterilization function is activated, ensuring that the full length of the nozzle is thoroughly cleaned with water.
The best way to clean carpet is to skip putting the shampoo into the carpet shampooer and fill it with plain old water instead. Cleaning with water will not only get your carpet clean, but will also keep it cleaner longer.
Mix Rug Doctor Carpet Cleaner with hot tap water in a clean bucket according to product label directions. Water should not be so hot as to scald or burn skin. The tank capacity is 9 litres.
A steam cleaner uses actual steam to clean various types of surfaces, and this steam can damage carpet fibers and remove the protection. A carpet cleaner is designed to force a mixture of hot water and cleaning solution into the carpet to clean deep down.
A good rule of thumb is to have your carpet professionally steam cleaned at least once a year, twice if you seem to track a lot of dirt in. This way you get a good, deep cleaning and don`t let the dirt build up. Vacuum once or twice a week to keep it clean in between your steam cleaning sessions.
Steam cleaning your carpets isn`t a complicated task to do yourself. There are those who consider going for a carpet cleaning service to get this done, but you should know that you can do it yourself as well. As soon as you are done vacuuming and dusting your carpet, the final step is steam cleaning.
Most carpets typically need 6-10 hours to dry completely. However, it could take up to 24 hours to dry depending on the time of year your carpets are cleaned, and the air circulation, humidity and temperature in your home.
Anything with fabric or upholstery needs frequent vacuuming. Dust settles deep into the fibers, holding onto pollutants, bacteria, and unwanted smells. Plan to vacuum carpet and area rugs at least twice per week, even if they don`t look dirty.
Dust before vacuuming
We recommend dusting before vacuuming, this is because dust particles usually get moved around the room when you dust, meaning all your hard work will go to waste. A top tip is to wait at least 2 hours after dusting to get the vacuum out.
Vacuum (spelled like so), means a complete lack of matter, or a device used for sucking up dirt or particles, or to use that device for cleaning. Vaccum and vacume are misspellings of vacuum.
For the electrical appliance that cleans surfaces through suction, North Americans tend to use vacuum cleaner, or just vacuum, and Britons tend to use hoover. Both words also function as verbs, inflected vacuumed, vacuuming, hoovered, and hoovering. By metaphorical extension, hoover also means to consume completely.
The motor in your vacuum cleaner is essentially safe from damage, however, when it is exposed to conditions other than what it was designed for, it can fail. The most common reason for vacuum motors failing is overheating.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
I do not have my users manual and have never vacuumed wet with this vacuum. How do I change it from a dry to wet vacuum.
Can’t find my manual and I need to use the shop vac for water in basement, do I have to change the filter or what
lost my user manual never used it to pick up water. need to know how to puit it in wet mode i want to clean the dirty water out of my pool.
Can’t find my manual and I need to use the shop vac for water in basement, do I have to change the filter or what
lost my user manual never used it to pick up water. need to know how to puit it in wet mode i want to clean the dirty water out of my pool.
ANSWER : .Vacuuming Liquids
.1. When picking up small amounts of liquid
.the filter may be left in place.
.2. When picking up large amounts of liquid
.we recommend that the filter be
.removed. If the filter is not removed, it
.will become saturated and misting
.may appear in the exhaust.
.3. After using the vac to pick up liquids,
.the filter must be dried to reduce the
.risk of possible mildew and damage to
.the filter.
.4. When the liquid in the drum reaches a
.predetermined level, the float mechanism
.will rise automatically to cut off
.airflow. When this happens, turn off
.the vac, unplug the power cord, and
.empty the drum. You will know that the
.float has risen because vac airflow
.ceases and the motor noise will
.become higher in pitch, due to
.increased motor speed.
.IMPORTANT: To reduce the risk of damage
.to the vac do not run motor with float
.in raised position
.1. When picking up small amounts of liquid
.the filter may be left in place.
.2. When picking up large amounts of liquid
.we recommend that the filter be
.removed. If the filter is not removed, it
.will become saturated and misting
.may appear in the exhaust.
.3. After using the vac to pick up liquids,
.the filter must be dried to reduce the
.risk of possible mildew and damage to
.the filter.
.4. When the liquid in the drum reaches a
.predetermined level, the float mechanism
.will rise automatically to cut off
.airflow. When this happens, turn off
.the vac, unplug the power cord, and
.empty the drum. You will know that the
.float has risen because vac airflow
.ceases and the motor noise will
.become higher in pitch, due to
.increased motor speed.
.IMPORTANT: To reduce the risk of damage
.to the vac do not run motor with float
.in raised position
Read Full Q/A … : Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
Dirt devil vacuum cleaner–trouble vacuuming dirt and pet hair on carpeting –is the problem with the spinning brush which contacts the floor, not contacting the carpeting?? I thought (when I bought this vacuum) that the aforementioned brush was adjustable to various heights of carpeting. Sometimes, it seems like nothing is being vacuumed up –unless I have just put a new bag on the vacuum… Do I need or can I replace the spinning brush on the bottom of the vacuum so it kicks up and vacuums
ANSWER : Try replacing the belt. Rubber belts stretch out after about a year.
Read Full Q/A … : Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
I need the manual for Hoover steam vacuum – Hoover F7431-900 SteamVac Vacuum
ANSWER : Go to your local vac. shop,they can get you one.
Read Full Q/A … : Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
I purchased a brand new Eureka Pet vacuum, sorry don’t know exact name but it the one that has the self cleaning duster on it. Last night I used the vacuum on my carpet, it was working fine until I accidently sucked up the corner of a scarf that was hanging off a couch. I shut the vacuum off, pulled out the scarf and and resumed vacuuming. Much to my dismay the suction on the vacuum had ceased. Can you tell me if there is a reset button on the vacuum? The vacuum does not appear to be damage
ANSWER : If the motor is running, there should be suction. Possible problems depend on whether it’s a canister or upright and are:
.A clog in the hose, UR or canister. Detach hose. Drop small coin in one end and lift hose causing it to roll out the other. If it does, no clog in hose. Drop same coin into hose opening on power head. If it rolls out, no clog in PN.
.Broken fan blades, UR. Needs to be taken to shop for repair/replacement.
.
.A reset button is for use if the motor isn’t running, so won’t have anything to do with the suction.
.A clog in the hose, UR or canister. Detach hose. Drop small coin in one end and lift hose causing it to roll out the other. If it does, no clog in hose. Drop same coin into hose opening on power head. If it rolls out, no clog in PN.
.Broken fan blades, UR. Needs to be taken to shop for repair/replacement.
.
.A reset button is for use if the motor isn’t running, so won’t have anything to do with the suction.
Read Full Q/A … : Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
SteamVac F5914-900 SpinScrub Upright Vacuum: Is it ok to use the hoover steamvac on tile floors…
ANSWER : Yes, your Steam VAc will work on tile floors. You’ll want to remove the rotating brushes and install the Bare Floor Tool attachment – Hoover part number 48417003
Read Full Q/A … : Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
I do not have my users manual and have never vacuumed wet with this vacuum. How do I change it from a dry to wet vacuum.
Can’t find my manual and I need to use the shop vac for water in basement, do I have to change the filter or what
Can’t find my manual and I need to use the shop vac for water in basement, do I have to change the filter or what
ANSWER : No – simply remove the filter. That is the only step necessary!!
.
.Hope your cleanup goes well!!
.
.Thanks for using FixYa – a FixYa rating is appreciated!!
.
.Hope your cleanup goes well!!
.
.Thanks for using FixYa – a FixYa rating is appreciated!!
Read Full Q/A … : Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
How do you turn it on lost manual – Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
ANSWER : Here is a link to the manual:
.http://www.hoover.com/pdfs/manuals/F5914900.pdf
.
.http://www.hoover.com/pdfs/manuals/F5914900.pdf
.
Read Full Q/A … : Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
Hoover SteamVac F7222-900 steamvac
Brushes do not spin.
Looked at filter as per manual instructions but it was free of lint.
Need to fix it, help please?
Vacuum was used less than 10/12 times
Brushes do not spin.
Looked at filter as per manual instructions but it was free of lint.
Need to fix it, help please?
Vacuum was used less than 10/12 times
ANSWER : Solution for Hoover SteamVac (F7452-900) brushes not spinning
.Uses the turbine model and same solution would be similar. Root cause is simply the main gear attached to turbine becomes stuck. This problem should not happen as often as I see other people also having this problem. Must be a poor design on Hoover’s part. It takes about 30 minutes and a Phillips screw driver and wrench. Pretty easy, just have to remember what screws went where.
.Remove brushes, and front suction cover
.On the bottom of the machine:
.Remove the 4 screws behind brushes which attach the top faceplate
.Remove the 2 screws from base in the sunken holes
.Remove the two long silver screws from base which connect all the way to turbine assembly
.Stand machine upright
.Remove the floor select switch handle
.Remove 1 screw near the center beside the intake hole
.Remove the 2 screws over the rear wheels
.Remove faceplate cover, the front will need to be gently pried over the clear plastic part, be careful about the upright disengaging lever under faceplate, move it under the metal wire
.Remove the 2 screws in the front of the turbine assembly
.Remove the 2 hoses on either side
.Disengage the bar on the floor selector switch
.Pull out the turbine assembly
.Remove the 4 screws and 3 clips to separate the assembly
.Remove the filter (which is most likely clean since, cleaning this is the manufactures only solution)
.Remove the large white gear and with a wrench remove ball bearing
.Remove other large white gear
.Note that the metal gear attached to turbine will not move (this was my problem), with a wrench gently grab metal gear and twist free. Spin turbine to make sure it moves freely.
Put everything back together again and you should be good to go.
.Uses the turbine model and same solution would be similar. Root cause is simply the main gear attached to turbine becomes stuck. This problem should not happen as often as I see other people also having this problem. Must be a poor design on Hoover’s part. It takes about 30 minutes and a Phillips screw driver and wrench. Pretty easy, just have to remember what screws went where.
.Remove brushes, and front suction cover
.On the bottom of the machine:
.Remove the 4 screws behind brushes which attach the top faceplate
.Remove the 2 screws from base in the sunken holes
.Remove the two long silver screws from base which connect all the way to turbine assembly
.Stand machine upright
.Remove the floor select switch handle
.Remove 1 screw near the center beside the intake hole
.Remove the 2 screws over the rear wheels
.Remove faceplate cover, the front will need to be gently pried over the clear plastic part, be careful about the upright disengaging lever under faceplate, move it under the metal wire
.Remove the 2 screws in the front of the turbine assembly
.Remove the 2 hoses on either side
.Disengage the bar on the floor selector switch
.Pull out the turbine assembly
.Remove the 4 screws and 3 clips to separate the assembly
.Remove the filter (which is most likely clean since, cleaning this is the manufactures only solution)
.Remove the large white gear and with a wrench remove ball bearing
.Remove other large white gear
.Note that the metal gear attached to turbine will not move (this was my problem), with a wrench gently grab metal gear and twist free. Spin turbine to make sure it moves freely.
Put everything back together again and you should be good to go.
Read Full Q/A … : Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
