Kenmore Vacuums\015 Need instruction manual for 116.25614504\015
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
Check service panel for tripped breakers/blown fuses. If breaker is tripped, reset it. If fuse is blown, replace it. If vacuum cleaner is plugged in, be sure power button is in the off position before resetting breaker/changing fuse.
A canister vacuum consists of a wheeled body that is attached to a vacuum wand and power head via a flexible plastic hose. The canister portion of the vacuum contains the main motor, filter, and any dust bags; depending on the model, the power head may also contain a smaller motor.
This overload reset switch button (part number 8191505) is for vacuums. Overload reset switch button 8191505 resets the overload switch when you push it. Unplug the vacuum before installing this part. Wear work gloves to protect your hands.
Wipe the inside of the canister with a dry microfiber cloth. Wash the canister in the sink with warm soapy water. Rinse away all soap suds. Let the canister dry completely before replacing it.
How long do Kenmore vacuums last? A. It`s suggested that the typical vacuum can last up to an average of eight years. With proper maintenance, a Kenmore vacuum could last that long or longer.
Vacuums: For the past decade, Kenmore`s flagship vacuums were made by Panasonic (less-expensive models came from TTI, Eureka, and PhoneMate). Now that Panasonic is winding down its North American small appliance business, upcoming Kenmore vacuums will be manufactured by a company called Cleva.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
I had the vacuum cleaner question about the canister and the wand/powerhead… the Kenmore Progressive Vacuum canister model 116.25812 and the canister not powering off without unplugging the vacuum. The solution I received that they both run on their own switch so it is normal makes sense. However, is there a power switch on the canister anywhere? The only way for the canister to be turned off is by unplugging it. Any ideas? One would think there would be a switch. I am new to fixya and hope
ANSWER : Hi. On some models, one switch controls all of the power. Your issue, which is no working switch is almost certainly a blown triac on the circuit board in the canister – kenmore part number KC86WBZRZ000
.Take it to your local vacuum repair shop and they should be able to fix it for a nominal fee.
Looks like a common fault with this particular model judging by the number of complaints on the web.
.Take it to your local vacuum repair shop and they should be able to fix it for a nominal fee.
Read Full Q/A … : Kenmore Vacuums
I do not have my users manual and have never vacuumed wet with this vacuum. How do I change it from a dry to wet vacuum.
Can’t find my manual and I need to use the shop vac for water in basement, do I have to change the filter or what
lost my user manual never used it to pick up water. need to know how to puit it in wet mode i want to clean the dirty water out of my pool.
Can’t find my manual and I need to use the shop vac for water in basement, do I have to change the filter or what
lost my user manual never used it to pick up water. need to know how to puit it in wet mode i want to clean the dirty water out of my pool.
ANSWER : .Vacuuming Liquids
.1. When picking up small amounts of liquid
.the filter may be left in place.
.2. When picking up large amounts of liquid
.we recommend that the filter be
.removed. If the filter is not removed, it
.will become saturated and misting
.may appear in the exhaust.
.3. After using the vac to pick up liquids,
.the filter must be dried to reduce the
.risk of possible mildew and damage to
.the filter.
.4. When the liquid in the drum reaches a
.predetermined level, the float mechanism
.will rise automatically to cut off
.airflow. When this happens, turn off
.the vac, unplug the power cord, and
.empty the drum. You will know that the
.float has risen because vac airflow
.ceases and the motor noise will
.become higher in pitch, due to
.increased motor speed.
.IMPORTANT: To reduce the risk of damage
.to the vac do not run motor with float
.in raised position
.1. When picking up small amounts of liquid
.the filter may be left in place.
.2. When picking up large amounts of liquid
.we recommend that the filter be
.removed. If the filter is not removed, it
.will become saturated and misting
.may appear in the exhaust.
.3. After using the vac to pick up liquids,
.the filter must be dried to reduce the
.risk of possible mildew and damage to
.the filter.
.4. When the liquid in the drum reaches a
.predetermined level, the float mechanism
.will rise automatically to cut off
.airflow. When this happens, turn off
.the vac, unplug the power cord, and
.empty the drum. You will know that the
.float has risen because vac airflow
.ceases and the motor noise will
.become higher in pitch, due to
.increased motor speed.
.IMPORTANT: To reduce the risk of damage
.to the vac do not run motor with float
.in raised position
Read Full Q/A … : Kenmore Vacuums
Dirt devil vacuum cleaner–trouble vacuuming dirt and pet hair on carpeting –is the problem with the spinning brush which contacts the floor, not contacting the carpeting?? I thought (when I bought this vacuum) that the aforementioned brush was adjustable to various heights of carpeting. Sometimes, it seems like nothing is being vacuumed up –unless I have just put a new bag on the vacuum… Do I need or can I replace the spinning brush on the bottom of the vacuum so it kicks up and vacuums
ANSWER : Try replacing the belt. Rubber belts stretch out after about a year.
Read Full Q/A … : Kenmore Vacuums
I purchased a brand new Eureka Pet vacuum, sorry don’t know exact name but it the one that has the self cleaning duster on it. Last night I used the vacuum on my carpet, it was working fine until I accidently sucked up the corner of a scarf that was hanging off a couch. I shut the vacuum off, pulled out the scarf and and resumed vacuuming. Much to my dismay the suction on the vacuum had ceased. Can you tell me if there is a reset button on the vacuum? The vacuum does not appear to be damage
ANSWER : If the motor is running, there should be suction. Possible problems depend on whether it’s a canister or upright and are:
.A clog in the hose, UR or canister. Detach hose. Drop small coin in one end and lift hose causing it to roll out the other. If it does, no clog in hose. Drop same coin into hose opening on power head. If it rolls out, no clog in PN.
.Broken fan blades, UR. Needs to be taken to shop for repair/replacement.
.
.A reset button is for use if the motor isn’t running, so won’t have anything to do with the suction.
.A clog in the hose, UR or canister. Detach hose. Drop small coin in one end and lift hose causing it to roll out the other. If it does, no clog in hose. Drop same coin into hose opening on power head. If it rolls out, no clog in PN.
.Broken fan blades, UR. Needs to be taken to shop for repair/replacement.
.
.A reset button is for use if the motor isn’t running, so won’t have anything to do with the suction.
Read Full Q/A … : Kenmore Vacuums
When we turn on the vacuum, the canister falls open. The clips holding the canister in place do not seem to hold the canister tightly which I’m sure that it did in the past. The clips do not look bent, but every time we turn on the vacuum the intense pressure blows the canister open only remaining attached the the rest of the vacuum by one clip
ANSWER : Check filter and make sure it is kept clean at regular intervals. Possibly worn out clip retainers on cannister side due to excessive pressure build up. Do not force closure unless pressure is back to normal. May crack cannister or damage unit beyond repair.
Read Full Q/A … : Kenmore Vacuums
I do not have my users manual and have never vacuumed wet with this vacuum. How do I change it from a dry to wet vacuum.
Can’t find my manual and I need to use the shop vac for water in basement, do I have to change the filter or what
Can’t find my manual and I need to use the shop vac for water in basement, do I have to change the filter or what
ANSWER : No – simply remove the filter. That is the only step necessary!!
.
.Hope your cleanup goes well!!
.
.Thanks for using FixYa – a FixYa rating is appreciated!!
.
.Hope your cleanup goes well!!
.
.Thanks for using FixYa – a FixYa rating is appreciated!!
Read Full Q/A … : Kenmore Vacuums
I was given a Kenmore progressive hepa filter 22313 Bagged Canister Vacuum recently, but don’t have the manual.
We used it once to vacuum the house and it worked beautifully. Then we used it 5-6 days later and it started whining and getting hot.
What year was this vacuum manufactured? Where can I download an owners manual??
Help!
ANSWER : Http://www.managemylife.com/mmh/owner_manuals/5461/KENMORE-Vacuum-Canister-L0809572
Read Full Q/A … : Kenmore Vacuums
I have an Ecectrolux Epic canister vacuum. As soon as it starts sucking, the vacuum cuts off. I put a new filter and bag in, but it doesn’t seem to help. If I open the front where the bag goes, take the bag out and depress the safety button the vacuum will run. Need some help or direction.
Thank you
Thank you
ANSWER : Try this.
.Disconnect hose. Turn machine on and place hand over intake. If it shuts off immediately, first try turning dial on top of machine so largest dot matches up with arrow. Turn on and place hand over intake again. If it still shuts off immediately, the “control valve assembly” is worn or broken and needs replaced. Don’t try this yourself.
.Take your complete machine to the nearest authorized Aerus Electrolux shop, or call and ask someone to pick it up. There’s no extra fee for this, or delivery upon repair.
.The repair/replacement should include a complete cleaning of your vacuum in the labor, but ask the service manager to be sure.
.The shop nearest you can be found by typing your zip code into the indicated space on the site listed below.
.
.http://www.aerushome.com/storelocator/
.Disconnect hose. Turn machine on and place hand over intake. If it shuts off immediately, first try turning dial on top of machine so largest dot matches up with arrow. Turn on and place hand over intake again. If it still shuts off immediately, the “control valve assembly” is worn or broken and needs replaced. Don’t try this yourself.
.Take your complete machine to the nearest authorized Aerus Electrolux shop, or call and ask someone to pick it up. There’s no extra fee for this, or delivery upon repair.
.The repair/replacement should include a complete cleaning of your vacuum in the labor, but ask the service manager to be sure.
.The shop nearest you can be found by typing your zip code into the indicated space on the site listed below.
.
.http://www.aerushome.com/storelocator/
Read Full Q/A … : Kenmore Vacuums
