Vacuums
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
A manual sweeper is used to clean floors, just like a vacuum cleaner. It houses a set of rollers which, when pushed along the floor, rotate and sweep dirt into an integrated container.
Dust before vacuuming
We recommend dusting before vacuuming, this is because dust particles usually get moved around the room when you dust, meaning all your hard work will go to waste. A top tip is to wait at least 2 hours after dusting to get the vacuum out.
Push harder than you pull.
Many people naturally exert more force when they`re pulling their vacuums back than when they`re pushing them forward, but this can leave dirt on the floor. Vacuums are designed to be pushed forward at a rate of about 12 inches per second and pulled back at a rate of 6 inches per second.
Manual Vacuum Pump is a handy accessory for vacuum packing all Status vacuum containers, jug, universal lids, and bottle stoppers. A few pulls will extract the air and create vacuum. Use it at home, on your travels, on holiday, and on your weekend retreats.
A central vacuum system (sometimes called a whole-house vacuum system) is a cleaning device installed throughout a building. Located in the garage or basement, a canister receives dust and debris sucked by the force of a motor from wall outlets, which are located for the homeowner`s convenience.
We have two possible ways of adjusting the pressure in a vacuum system: first, by changing the pumping speed (altering the speed of the pump or throttling by closing a valve); second, through admission of gas (opening a valve).
The vacuum forming process works by heating a plastic sheet, forming it into a shaped vacuum forming tool using vacuum, cooling the plastic sheet until it sets hard & then removing the part from the tool.
Empty the vacuum cleaner, discard the contents in the outside trash and use an anti-bacterial wipe to clean the vacuum. Let it dry thoroughly. If your manufacturer says your vacuum cannister is washable, wash it out with warm, soapy water and then rinse it and let it dry.
The dust that enters the air can settle in the smallest or most awkward-to-access places, which is why most cleaning professionals always recommend that you dust before you vacuum to help you capture as much as possible. Dusting first is essential if it has been a considerable time since you last dusted.
Take your time. Vacuuming slowly will allow your machine to suck up more dirt and dust, and ultimately get your rugs and carpets much cleaner. Slow vacuuming allows the brush to agitate the carpet properly and suck up the unclean bits that emerge.
“We would recommend vacuuming at least once or twice a week—and more often if we have pets—with the right tools to remove dust quickly and effectively,” Patel advises.
The time allowed for decay depends upon the size of the system, but generally, 10 minutes minimum with 1 minute added per ton is a good guideline. The moral of the story is this: A proper evacuation may take 15 minutes, 15 hours, or 15 days, it simply takes what it takes.
Simply put, vacuum pumps are mechanical devices that enable the removal of air and gas molecules from a sealed area to create an area devoid of air and/or gas. Generally, their purpose is to clean and seal.
Vacuum pumps are simply compressors that take in gas at a pressure lower than atmospheric pressure, compress it, and discharge the gas at atmospheric pressure. Since gas at low pressures has a large volume, vacuum pumps tend to be bulky.
Start on the far edge of your carpet or rug and push the vacuum forward in a straight line. This movement lifts the nap (or fibers) of the floor covering to reveal any dirt or debris hidden underneath. Then pull the machine back slowly toward you to collect all that debris.
Vacuum regulators control the pressure within a system in a more efficient fashion than more traditional single-valve seats. The spring-loaded diaphragm mechanism throttles the air flow from either a pump or external ambient air source in order to better regulate internal pressure.
All vacuum cleaners operate based on air flowing from the opening at the cleaning head or tool, through the vacuum cleaner and the bag and/or filter system and then out the exhaust port. This airflow is created by the vacuum motor, which also may be referred to as the suction motor.
Replace the Brush Belt
If the vacuum is still hard to push, tilt it back far enough that you can inspect the moving brush while the vacuum is running. Be careful to avoid getting too close to the moving parts. If you see that the brush is not turning, that means you will need to replace the brush belt.
Vacuum uses the surrounding atmosphere to create work force by pulling on, rather than pushing, a work piece.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
Dirt devil vacuum cleaner–trouble vacuuming dirt and pet hair on carpeting –is the problem with the spinning brush which contacts the floor, not contacting the carpeting?? I thought (when I bought this vacuum) that the aforementioned brush was adjustable to various heights of carpeting. Sometimes, it seems like nothing is being vacuumed up –unless I have just put a new bag on the vacuum… Do I need or can I replace the spinning brush on the bottom of the vacuum so it kicks up and vacuums
ANSWER : Try replacing the belt. Rubber belts stretch out after about a year.
Read Full Q/A … : Vacuums
I purchased a brand new Eureka Pet vacuum, sorry don’t know exact name but it the one that has the self cleaning duster on it. Last night I used the vacuum on my carpet, it was working fine until I accidently sucked up the corner of a scarf that was hanging off a couch. I shut the vacuum off, pulled out the scarf and and resumed vacuuming. Much to my dismay the suction on the vacuum had ceased. Can you tell me if there is a reset button on the vacuum? The vacuum does not appear to be damage
ANSWER : If the motor is running, there should be suction. Possible problems depend on whether it’s a canister or upright and are:
.A clog in the hose, UR or canister. Detach hose. Drop small coin in one end and lift hose causing it to roll out the other. If it does, no clog in hose. Drop same coin into hose opening on power head. If it rolls out, no clog in PN.
.Broken fan blades, UR. Needs to be taken to shop for repair/replacement.
.
.A reset button is for use if the motor isn’t running, so won’t have anything to do with the suction.
.A clog in the hose, UR or canister. Detach hose. Drop small coin in one end and lift hose causing it to roll out the other. If it does, no clog in hose. Drop same coin into hose opening on power head. If it rolls out, no clog in PN.
.Broken fan blades, UR. Needs to be taken to shop for repair/replacement.
.
.A reset button is for use if the motor isn’t running, so won’t have anything to do with the suction.
Read Full Q/A … : Vacuums
Kenmore Progressive canister model 116.27514700
Problem: Vacuum motor won’t turn on. The power head operates, but nothing from the vacuum. Have checked all areas of airflow: hose, bag, motor filter and hepa filter. All are fine. Have checked and rechecked all electrical connections, all seem to be in working order. Vacuum hasn’t run for a week or so, so it’s not the thermal protector, unless it’s defective. Vacuum was running fine last week. Didn’t stop operating when using. Went to v
Problem: Vacuum motor won’t turn on. The power head operates, but nothing from the vacuum. Have checked all areas of airflow: hose, bag, motor filter and hepa filter. All are fine. Have checked and rechecked all electrical connections, all seem to be in working order. Vacuum hasn’t run for a week or so, so it’s not the thermal protector, unless it’s defective. Vacuum was running fine last week. Didn’t stop operating when using. Went to v
ANSWER : Hello! The culprit is the PCB Assembly;
Part # KC86WBZR3000…Cost is $6.99. I would remove and inspect for burnt components, or broken wires…Then clean connections both male/female using an eraser, toothbrush and alcohol…Using a bright light and a magnifying glass inspect solder joints for “bridges” or cold joints. If you detect a problem during this procedure (to the exclusion of burnt components) fix, reassemble, and test. If problem still persist: Order a new part.
Part # KC86WBZR3000…Cost is $6.99. I would remove and inspect for burnt components, or broken wires…Then clean connections both male/female using an eraser, toothbrush and alcohol…Using a bright light and a magnifying glass inspect solder joints for “bridges” or cold joints. If you detect a problem during this procedure (to the exclusion of burnt components) fix, reassemble, and test. If problem still persist: Order a new part.
if you have any question feel free to send a comment.
Guru……………..saailer
Read Full Q/A … : Vacuums
I need a parts manuel and a owners manuel – Eureka Altima Upright Vacuum Model 2996AVS Vacuum
ANSWER : Go to eureka.com and look for your model and find the manual you can download it
Read Full Q/A … : Vacuums
I do not have my users manual and have never vacuumed wet with this vacuum. How do I change it from a dry to wet vacuum.
Can’t find my manual and I need to use the shop vac for water in basement, do I have to change the filter or what
lost my user manual never used it to pick up water. need to know how to puit it in wet mode i want to clean the dirty water out of my pool.
Can’t find my manual and I need to use the shop vac for water in basement, do I have to change the filter or what
lost my user manual never used it to pick up water. need to know how to puit it in wet mode i want to clean the dirty water out of my pool.
ANSWER : .Vacuuming Liquids
.1. When picking up small amounts of liquid
.the filter may be left in place.
.2. When picking up large amounts of liquid
.we recommend that the filter be
.removed. If the filter is not removed, it
.will become saturated and misting
.may appear in the exhaust.
.3. After using the vac to pick up liquids,
.the filter must be dried to reduce the
.risk of possible mildew and damage to
.the filter.
.4. When the liquid in the drum reaches a
.predetermined level, the float mechanism
.will rise automatically to cut off
.airflow. When this happens, turn off
.the vac, unplug the power cord, and
.empty the drum. You will know that the
.float has risen because vac airflow
.ceases and the motor noise will
.become higher in pitch, due to
.increased motor speed.
.IMPORTANT: To reduce the risk of damage
.to the vac do not run motor with float
.in raised position
.1. When picking up small amounts of liquid
.the filter may be left in place.
.2. When picking up large amounts of liquid
.we recommend that the filter be
.removed. If the filter is not removed, it
.will become saturated and misting
.may appear in the exhaust.
.3. After using the vac to pick up liquids,
.the filter must be dried to reduce the
.risk of possible mildew and damage to
.the filter.
.4. When the liquid in the drum reaches a
.predetermined level, the float mechanism
.will rise automatically to cut off
.airflow. When this happens, turn off
.the vac, unplug the power cord, and
.empty the drum. You will know that the
.float has risen because vac airflow
.ceases and the motor noise will
.become higher in pitch, due to
.increased motor speed.
.IMPORTANT: To reduce the risk of damage
.to the vac do not run motor with float
.in raised position
Read Full Q/A … : Vacuums
I have a Kirby G4 Vacuum Cleaner – MOdel G4 D. I have never had any problems or repairs done to it in the past ten plus years that I’ve had it. This is an upright vacuum. I was vacuuming the carpet floor and was not having any trouble at all. I switched the vacuum off and moved it into a different room. When I tried to turn on the vacuum, it would not turn on. I checked with different outlets, used both front attachment and hose attachment. Checked the front part of the motor/ spiral case. This
ANSWER : Hello,
.My educated guess is that it’s either the switch or the power cord. Here are a couple of guides to help with diagnosis and repair…
.
.http://reviews.ebay.com/COMMON-PROBLEMS-WITH-THE-KIRBY-VACUUM-TROUBLESHOOTING_W0QQugidZ10000000003800312
.
.http://reviews.ebay.com/REPLACING-THE-POWER-SWITCH-ON-ANY-KIRBY-G-SERIES-VACUUM_W0QQugidZ10000000003752018
.
.Hope this helps!!
.Marci
.My educated guess is that it’s either the switch or the power cord. Here are a couple of guides to help with diagnosis and repair…
.
.http://reviews.ebay.com/COMMON-PROBLEMS-WITH-THE-KIRBY-VACUUM-TROUBLESHOOTING_W0QQugidZ10000000003800312
.
.http://reviews.ebay.com/REPLACING-THE-POWER-SWITCH-ON-ANY-KIRBY-G-SERIES-VACUUM_W0QQugidZ10000000003752018
.
.Hope this helps!!
.Marci
Read Full Q/A … : Vacuums
Unbeknownst to me, someone took the bag out of my Kenmore Progressive vacuum and failed to replace it. I have been vacuuming without a bag for months, and today the vacuum stopped sucking. When I opened up the front to replace the bag, tons of dirt and dust came pouring out. I thoroughly cleaned the vacuum, put in a new bag, but still no sucking power. Just dust coming from the rear vents where one of the filters is. Is the vacuum ruined, or is it a simple solution of buying a new filter?
ANSWER : Sounds like you need to buy a new motor. All that grit and dust will ruin a motor and I’m surprised it lasted as long as it did.
.This is where a vacuum that won’t run without a bag would have been nice. (Aerus for one)
.This is where a vacuum that won’t run without a bag would have been nice. (Aerus for one)
Read Full Q/A … : Vacuums
I have a kenmore progressive direct drive handi mate jr. upright vacuum. My daughter used it last night to vacuum up some cat litter that had spilled on the floor. I went to use it today and it turned on for a second and then stopped working. I have hit the reset button but it will not turn on. Help this vacuum is only 2 years old Is there anything that I need to reset or do so that the vacuum will work again?
ANSWER : Its probably clogged up with cat litter.might have gotten into the motor.your motor has a motor guard inside if it. when it overheats it will shut down till it cools off.you need to clean all th cat liter out of it.and clean the filters.with a direct drive you might want to take it in to a repairman to sevice. its not a shop vac i advise you not to pick up things like cat liter
Read Full Q/A … : Vacuums
